Security screws - Import export

Sleeve 1.4305. Ball 1.4034. Spring 1.4310. LONG-LOK thread lock, Nylon.

iglidur® flange bearing d1 [mm]: With this design it is possible to use the iglidur® high-performance bearings where housing bores with no precise tolerances are possible. When to use iglidur® flange bearings? When you want a screw flanged bearing When a clip bearing solution is not satisfactory as a sheet metal feedthrough When there is a housing with very rough tolerances When the tight fit of a press-fit bearing is not sufficient as an axial securing When not to use them? When an additional angle compensation is required igubal® flange bearing When a screw connection is not possible iglidur® clip bearing When a large guide length is necessary iglidur® G General features With this design it is possible to use the iglidur® high-performance bearings where housing bores with no precise tolerances are possible. The design enables high loads with minimum demand on the precision of the housing. iglidur® maintenance-free flange bearings are available in four materials - iglidur® G, iglidur® J, iglidur® X and iglidur® A180. Thus, with this design, a very wide range of applications - from the universal bearing through the highest wear resistance or temperature resistance (up to +250°C) up to FDA-compliant bearing solutions - can be covered. Installation Dependent on the stressing capacities, various mounting types are used. For low radial loads, it is enough to mount the iglidur® flange bearing with just two screws on a surface. For higher radial loads, it is advisable to support the iglidur® flange bearing in a bore on the reinforced side in the load direction. Large tolerances are permitted for this bore, as it is only to additionally support the iglidur® flange bearing. In order to support still higher radial loads, the iglidur® flange bearing can be press-fitted with the longer side in an H tolerance bore. The additional screw connection secures the firm seating of the bearing in the housing. For the mounting of the iglidur® maintenance-free flange bearing, no special tools or devices are necessary. The alignment of the bearing in multiple mounted shafts is easily possible at the installation. Available materials: iglidur® G, iglidur® A180, iglidur® J and iglidur® X The mounting of the iglidur® flange bearing: Simple and safe iglidur® flange bearing d1 [mm]:

da [mm]: DryLin® overview DryLin® gliding pads available from stock made of high-performance plastic iglidur® J can be virtually used everywhere. Without additional lubrucant, heavy loads can be moved over a variety of surfaces (steel, aluminium, stainless steel, etc.) with very low friction. The plates are fixed securely with a screw through the reinforced hole in the middle. da [mm]:

Steel grade 8.8, black. Stainless steel A 2-70, bright. Drawing reference: L2 = approx. 2x thread pitch

Ground anchors, ground screws or screw anchors are used in various applications, such as: Stable earth screw foundation: Perfect solution for garden sheds, gazebos, greenhouses, patios and carports, for permanent or temporary applications (reusable, as long as not damaged), can be loaded immediately even in winter Bracing of poles: Ground anchors are used to securely anchor masts to the ground and to absorb tensile forces. This is particularly important in situations where where high stability and safety are required, for example installation of antenna masts or for temporary constructions constructions such as event stages. Recovery of vehicles: Ground anchors can be used as anchor points to secure vehicles during recovery or rescue operations. rescue operations. They provide a reliable anchorage in the ground to absorb tractive forces and allow safe towing or towing or moving vehicles off-road.

The required torque is set by a set screw and a graduated scale. The set value can be secured using the lateral clamping screw. When the set torque is reached the grip audibly and palpably releases. The loosening torque is higher than the tightening torque so that the torque handle can be released without any problems. The internal thread version has a hole in the set screw so that the torque handle can also be used on threaded rods. Set torque accuracy ± 5%. On request: Other thread lengths.

Housing, stainless steel 1.4301. Bearing, stainless steel 1.4125. Seal, rubber NBR. Note Pillow block bearings consist of a sealed singlerow ball bearing with a spherical outer ring which is mounted in a housing. Because of the spherical outer surface of the bearing, shaft misalignment can be compensated for. The bearings are manufactured with a plus tolerance. This results in transition or press fits when using shafts with htolerances. The shaft is secured by grub screws on the inner ring. In normal applications, pillow block bearings are maintenancefree due to the lifetime lubrication. In difficult environmental conditions relubrication can be carried out over the grease nipple. All housing dimensions are nominal dimensions for which the usual casting tolerances must be taken into consideration.

Material Ballbearing steel 100Cr6. Seal, rubber NBR. Version Sealed on both sides with a spherical outer ring. Can be relubricated. Note The internal construction of the insert bearings corresponds to that of standard Series 6200 and 6300 radial ball bearing. However, they have wider inner rings for easier fastening on shafts. The inner rings are manufactured with a plus tolerance. This results in transition or press fits when using shafts with htolerances. The shaft is secured by 2 grub screws positioned 120° apart on the inner ring. The insert bearings are ready to install and are permanently lubricated with a suitable ball bearing grease. In normal applications, relubrication is not necessary.

Housing, grey cast iron. Bearing, ballbearing steel 100Cr6. Seal, rubber NBR. Pillow block bearings consist of a sealed singlerow ball bearing with a spherical outer ring which is mounted in a housing. Because of the spherical outer surface of the bearing, shaft misalignment can be compensated for. The bearings are manufactured with a plus tolerance. This results in transition or press fits when using shafts with htolerances. The shaft is secured by grub screws on the inner ring. In normal applications, pillow block bearings are maintenancefree due to the lifetime lubrication. In difficult environmental conditions relubrication can be carried out over the grease nipple. All housing dimensions are nominal dimensions for which the usual casting tolerances must be taken into consideration.

For the simple and safe locking of doors and hatches. Installed from the front without mechanical processing using M6 cylinder-head or cheese-head screws. Secured to prevent removal when locked. The key-operated version is supplied with 2 keys. The key can be removed in both positions (open and closed). The locks are keyed alike, i.e. they can all be opened using the same key (euro key 5333). The double-lug version is supplied with a double lug key. Drawing reference: Actuation: a) single-key system b) square 8 mm c) double lug 5 mm

Steel 1.0718. Stainless steel 1.4305. Version Steel black oxidised. Stainless steel bright. Note Rigid couplings transmit high torques without rotational play. They are used where there are no shaft displacements or alignment errors. Wearfree and maintenancefree. Screws secured to avoid vibration induced loosening. The maximum torque transmission can only be achieved through optimal installation and correct shaft dimensions. Maximum speed 4000 rpm.

High strength stainless steel adhesive For permanent connections Secure screws and fill gaps