Results for
NORELEM FRANCE
France
The floating joint unit is a bolt for connecting two components, that permits a desired movement of those components in relation to each other. The floating joint unit is mainly used when: a temperature change alters the dimensions of a component assembly inaccuracies occur manufacturing tolerances must be compensated for the position of the components varies due to dynamic loads
Request for a quoteNORELEM FRANCE
France
Rest pads are for supporting machined and non-machined parts. They can also be used as stops and thrust pads in fixtures and toolmaking. Studs or grub screws can be screwed and glued into the tapped hole D to make a rest pad with external thread.
Request for a quoteNORELEM FRANCE
France
Hardened and ground. Top face without centerbore. Note: If more than one rest pad is used, the support height can be reground. Rest pads can also be used as feet for jigs and fixtures.
Request for a quoteNORELEM FRANCE
France
Worm screw steel. Worm wheel CuZn37Mn3Al2PbSiS40. Version Worm screw with righthand pitch, casehardened HV 620 – 700, flanks and hole ground. Note for ordering Wheels/screws can only be combined to form a worm gear if they have the same centre distance and transmission ratio. Note A worm gear consists of a worm screw (shaft) and a worm wheel. Suitable for forming worm drives with a 90° shaft angle. A worm drive enables very large speed reduction ratios with a single stage. The toothing has the flank shape K. The engagement angle is 15°. The worm gears are prebored. The stated T2 output torques are the permissible output torques on the worm wheel. These apply for an input speed of 2800 rpm of the worm screw. The worm gears are suitable for continuous operation at high speeds and high torques. Attention 22500171002 Screw polished only. 22500172002 Worm wheel with helical gear toothing.
Request for a quoteNORELEM FRANCE
France
Slides steel. Ball cages steel. Balls, steel. Version Slides electro zincplated. Ball cages, electro zincplated. Balls hardened. Note for ordering Sold in pairs. Note By telescopic slides with full extension, the travel is roughly equal to the installed length, which ensures greater comfort and accessibility. The dynamic load capacity of the telescopic slides indicates the maximum load rating of a vertically mounted slide pair when the entire extension length is used. The load capacity specified is calculated with a slide spacing of 450 mm and is based on the maximum value with 80,000 cycles. Not suitable for horizontal mounting. The head height of the fastening screws should not exceed 1.8 mm otherwise there is a risk of collision with other parts of the slide. Advantages Low slide thickness Light running Precise guidance for high lateral stability
Request for a quoteNORELEM FRANCE
France
Slides steel. Ball cages steel. Balls, steel. Version Slides electro zincplated. Ball cages, electro zincplated. Balls hardened. Note for ordering Sold in pairs. Note On telescopic slides with partial extension both sides, the travel is less than the installed length. Latches in open position on both sides. The dynamic load capacity of the telescopic slides indicates the maximum load rating of a vertically mounted slide pair when the entire extension length is used. The load capacity specified is calculated with a slide spacing of 450 mm and is based on the maximum value with 50,000 cycles. The load capacity is ca. 75% lower by horizontal mounting. The head height of the fastening screws should not exceed 2.5 mm otherwise there is a risk of collision with other parts of the slide. Advantages Pulls out in both directions Latches in open position on both sides Light running
Request for a quoteNORELEM FRANCE
France
Polyethylene. Screw, steel. Note: Levelling feet with hexagonal base. Rigid version.
Request for a quoteMETFIX GROUP
Kazakhstan
Roofing self-tapping screw for metal DIN-EN-ISO 15480 (old - DIN 7504-K) with an EPDM washer 2.4-2.8 mm thick Standard Head: hexagonal with a shoulder, , turnkey 8 (D-5.5) or 10 (D-6.3) mm, a marking mark in the form of the letter "X" is stamped on the cap
Request for a quoteMETFIX GROUP
Kazakhstan
Self-tapping screw for fastening, connecting sheet metal and metal profiles up to 0.9 mm Head: hexagonal with a shoulder, straight slot
Request for a quoteOTTO EICHHOFF GMBH & CO. KG
Germany
During re-machining, a cutting tool is used to remove material from a workpiece in order to shape or surface it as required. We offer re-machining (turning, twisting) as wage work. The following machining operations we offer: Turn thin stem, pins and tips Screw punctures, approaches and undercuts Heads of screws / cold shaped parts machining process (turning) further machining operations are possible on request. Our curve-controlled automatic Audrema lathes offer you further possibilities of finishing cold-moulded parts. These automatic lathes are designed to achieve maximum precision and reproducibility at high throughputs. Short loading and unloading times permit economical production of medium-sized and large series.
Request for a quoteNORELEM FRANCE
France
The surface of the hexagon head bolt is polished and, with regard to design optimised for the use in hygienic environments. The bolt head is convex on the top face and the collar has a conical formed top surface. Instead of troublesome embossing or indentations, the bolt head is smooth with a surface finish of Ra 0.8 µm. Dirt and residue from products or cleaners seldom adheres and easy cleaning is ensured.
Request for a quoteNORELEM FRANCE
France
Self-locking trapezoidal thread, spindle has end lock. Note: The through hole allows easy clamping and positioning of the workpiece. Drawing reference: 1) centring hole for 02210
Request for a quoteNORELEM FRANCE
France
Hook clamps and clamping screw carbon steel, tempered.
Request for a quoteNORELEM FRANCE
France
Surfaces which are not flat and parallel can be firmly clamped or supported with with a flattened ball, the movable ball can adapt itself up to 9°. Longer versions have been designed especially to be glued in. This allows mechanical connecting elements with external thread to be made cost-effectively for small and medium-sized series. The ball has a rotation lock.
Request for a quoteSOOCHOW ADVANCE INDUSTRIES CO., LTD.
China
truss head shoulder screw thread: 8-32 UNC-2A head height: 0.170 +/- 0.015 inch, head diameter: 0.500 +/- 0.015 inch rod length: 0.875 +/- 0.062 inch groove width: 0.064 +/- 0.015 inch, depth: 0.074 +/- 0.015 inch material: steel surface finish: zinc plated Soochow Advance Industries Co., Ltd., (website: www.sai-parts.com) supplies custom OEM mechanical parts, industrial fasteners, screws, bolts, nuts, industrial fittings, electronic hardware by precision CNC machining, CNC turning, CNC milling, CNC engineering.
Request for a quoteEUROPONTEX IMPORTAÇÂO & EXPORTAÇÂO
Portugal
Steel fasteners
Request for a quoteCOLORICIO.SRL
Romania
Round steel / Square steel, Flat steel , L cornier profile , IPE Steel and much more
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
KRAUS GMBH GLASBESCHLÄGE
Austria
Modern look through minimal attachment points Suitable for glass, wood, metal, plastic or stone panels Rustproof due to stainless steel AISI 304
Request for a quoteKRAUS GMBH GLASBESCHLÄGE
Austria
Modern look through minimal attachment points Suitable for glass, wood, metal, plastic or stone panels Rustproof due to stainless steel AISI 304
Request for a quoteKRAUS GMBH GLASBESCHLÄGE
Austria
Modern look through minimal attachment points Suitable for glass, wood, metal, plastic or stone panels Rustproof due to stainless steel AISI 304
Request for a quoteKRAUS GMBH GLASBESCHLÄGE
Austria
Modern look through minimal attachment points Suitable for glass, wood, metal, plastic or stone panels Rustproof due to stainless steel AISI 316
Request for a quoteKRAUS GMBH GLASBESCHLÄGE
Austria
Modern look through minimal attachment points Suitable for glass, wood, metal, plastic or stone panels Rustproof due to stainless steel AISI 304
Request for a quoteKRAUS GMBH GLASBESCHLÄGE
Austria
Modern look through minimal attachment points Suitable for glass, wood, metal, plastic or stone panels Rustproof due to stainless steel AISI 304
Request for a quoteKRAUS GMBH GLASBESCHLÄGE
Austria
Modern look through minimal attachment points Suitable for glass, wood, metal, plastic or stone panels Rustproof due to stainless steel AISI 304
Request for a quoteKRAUS GMBH GLASBESCHLÄGE
Austria
Modern look through minimal attachment points Suitable for glass, wood, metal, plastic or stone panels Rustproof due to stainless steel AISI 304
Request for a quoteKRAUS GMBH GLASBESCHLÄGE
Austria
Modern look through minimal attachment points Suitable for glass, wood, metal, plastic or stone panels Rustproof due to stainless steel AISI 304
Request for a quoteKRAUS GMBH GLASBESCHLÄGE
Austria
Modern look thanks to minimal attachment points Point holder for railing systems Rustproof due to stainless steel AISI 304
Request for a quoteKRAUS GMBH GLASBESCHLÄGE
Austria
Modern look thanks to minimal attachment points Point holder for railing systems Rustproof due to stainless steel AISI 304
Request for a quoteKRAUS GMBH GLASBESCHLÄGE
Austria
Adjustable from the front No disassembly of the glass necessary With oblong hole for optimal fit
Request for a quoteResults for
Screws in steel - Import exportNumber of results
38 ProductsCountries
Company type