Railings - Import export

Crane Rails (A series A45/55/65/75/100/120/150) Light Rails (S10/S14/S18/..) Train Rails Grooved Rails Traverse system (Pre-stressing Wires.) Complete with fastenings systems, pads.

Rail transport is one of the few opportunities for moving large volumes of cargo by land. Thanks to these exceptional capabilities, his services are in maximum demand in all industries, both now and in the future. A rail is an element of a railway track, which directly takes the entire load of the rolling stock. Constructed from carbon steel and fixed to timber or concrete sleepers We offer domestic made railway rails and other rail products widely used in Ukraine of various types and modifications for wholesale and retail purchases, as well as components for them. The range of rails we offer makes it possible to repair a wide range of types of rail fasteners, from access roads of industrial enterprises leading to main roads, to industrial rail sections located inside buildings, turnouts, underground mine tracks, as well as their construction. The length of a railroad train is from 12.5 to 100 meters. You can contact us by mail - marketing@stalevar.com or by phone +380675624220.

Rails

Profile guide rails can be screwed on from above. The profile guide rails are available in four sizes and one or more carriages can be assembled on them. 4row versions with round arch profile. The tracks of the profile guide rails are set below an angle of 45° and thus can carry loads from all directions. The profile guide rails correspond to the market standard and can replace linear guides of the same design by other manufacturers. On request Lengths up to a max. 3960 mm.

Electro zincplated. Tracks inductively hardened and ground. Note for ordering Fastening screws are supplied. Note Compact Cprofile guide rails with internal hardened tracks. The system runs with low noise even under heavy loads. There is play between the screw and the fastening hole to allow the rail to be aligned during installation. To achieve the desired running properties there must always be a film of lubricant between track and roller, this also provides corrosion protection for the ground tracks. On request Lengths up to max. 4080 mm.

Attachments farm loader: Farm rail for Ferrum DM farm loader / wheel loader suitable for the wheel loaders and farm loader models listed below requires a rear control circuit for lifting and lowering for attachments that can be attached to the farm rail we look forward to your inquiry directly from the manufacturer Ferrum Maschinen with its selected field rail products. Recommended for: Wheel loader Ferrum DM416 x4 V2 Ferrum DM522 x4 Ferrum DM430 x4 DLZ Ferrum DM625 x4 Ferrum DM732 x4 Court loader: Courtyard loader FIRST 16

Manufacturing and distribution of protective raillings for industry

DryLin® N miniature gliding systems - basics DryLinN2010.wmv DryLin® N - Installation video of the gliding elements DryLin_N_Montage.wmv DryLin® N - Technical data DryLin® linear guide systems in the cleanroom DryLin® N - Applications DryLin® N - Design rules System selection & service life calculation NW 17 = 17 mm rail width The smallest type series of the drylin® N series distinguishes itself by the lowest dimensions and high stressing capacity. This series operates free of lubrication and offers the potential to execute high-speed applications. Variants: Standard, Preload (P), floating bearing (LL) extrem low weight Quiet running Installation height 6 mm up to 50 N load NW 17 Preload (with pretension)The NW 17 Preload model of the drylin® N series displays, in addition to the features of the NW 17, an automatic pre-stressing within the rail. Freedom from lubricants and the potential to execute high travel speeds distinguish this series. DryLin® N - Low profile linear guide system NK-02-17 DryLin® N - Low profile linear guide system NK-22-17-40 drylin® N - Low profile linear guide system NK-22-17-30 NW 27 = 27 mm rail width The installation size 27 offers the largest range of various guide carriages. They vary in the connecting potentials, lengths and precision. The injection-molded types additionally facilitate the stocking and installation. NW 27 Preload (with pretension) Identical version to the DryLin® standard carriage NW-01/02-27 and NW-02-40 respectively. The version injection-molded with iglidur® J offers an enhanced installation-friendliness and easier storage for large quantities. Features like the high wear resistance as well as low coefficients of friction remain unchanged. Over 20 carriage options 9.5 mm installation height 100% lubricant-free iglidur® J plain bearing material up to 500 N Last Best selling linear guide DryLin® N - Low profile linear guide system NK-01-27 DryLin® N - Low profile linear guide system NW-21-27-60P DryLin® N - Low profile linear guide system NK-11-27-80 DryLin® N - Low profile linear guide system NK-02-27 DryLin® N - Low profile linear guide system NW-22-27-60P DryLin® N - Low profile linear guide system NK-12-27-80 NW 40 = 40 mm rail width The dimension 40 defines itself by the rail width of 40 mm and ideally fits standard aluminum profiles. The carriages are available with threaded pin or through hole. The gliding elements are available as clip version or directly injection-molded. Lightweight Installation height 9,5 mm high speeds are possible (up to 5 m/s) iglidur® J plain bearing material up to 700 N Last DryLin® N - Low profile linear guide system NK-01-40 DryLin® N - Low profile linear guide system NK-02-40 drylin® N - low profile linear guide system preload NW-01-40P drylin® N - low profile linear guide system preload NW-02-40P NW 80 = 80 mm rail width The largest series in the DryLin® N type series offers the potential to take high loads with low installation height. The largest series also operates free of lubrication and can undertake high-speed applications. The gliding elements can be replaced in the clips option, and the injection-molded option facilitates the installation. Installation height 12 mm 100% lubricant-free Wide torque support up to 1000 N Last Gliding elements made of iglidur® J or J200 DryLin® N - Low profile linear guide system NK-02-80 Telescope system Mounting rails: Anodized aluminum Intermediate rail: Plastic Options: Full extension, over extension (+ 20 mm), partial extension Continuous lengths up to 1200 mm extended total length Lubricant-free Low noise Corrosion resistant From stock DryLin® telescopic rails End caps. The new plastic end caps, suitable for DryLin® N rails, offer „protection against loss“ for the carriages and cover the open sharp edges of the profi les safely and in an aesthetic way. Easy installation Low-priced Dismantling possible High retention force DryLin® N end caps Low profile linear axis - SLN-27-01 SLN-27-01: Linear axis for manual operation with hand wheel (SHT-HR-05-22-15-OG) SLN-BB-27-01: Ball bearing linear axis for manual adjustments with hand wheel 100 / 150 / 200 / 250 mm strokes Small (installation height from 22 mm), light and flat Plastic plain bearings in the bearing points Feed with spindle Ø 5 and pitch 0.8 and/or 5 mm Manual and motorized operation drylin® miniature linear axis Low profile linear axis - SLN-27-02 SLN-27-02: Linear axis with NEMA11 stepper motor, ball bearing spindle over motor bearing SLN-BB-27-02: Ball bearing linear axis with NEMA11 stepper motor Small (installation height from 22 mm), light and flat Plastic plain bearings in the bearing points M5-thread (5x0,8 mm), steep thread 5x5 and 6x12,7 Manual and motorized operation drylin® SLN low profile linear axis with motor DryLin® N low profile guide systems offer you low profiles in various widths. Like in all drylin® products, the carriage runs without lubrication in anodized aluminum profiles. The material used and the unique design make DryLin® N a cost-efficient and flexible guide system. Technical data Gliding elements: Maintenance-free Material: iglidur® J * Max. surface speed: 15 m/s Operating temperature: -40°C to +90°C *Other materials on request 1 Rail made of anodized aluminum 2 Gliding elements made of iglidur® J or J200 3 Carriage made of chromated zinc or plastic 4 Carriage with threaded hole or through hole Advantages: Small installation height between 6 and 12 mm Lightweight Numerous carriage options – also with pretension Maintenance-free, self lubricating Corrossion-resistant Low wear with low coefficient of friction Rails in silver or black anodized When not to use ? When precision below 50 μ is required In high loads over 50 kg drylin® T drylin® R drylin® W When high resistance to chemicals is required drylin® W drylin® R DryLin® N miniature gliding systems - basics DryLinN2010.wmv DryLin® N - Installation video of the gliding elements DryLin_N_Montage.wmv Standard, preload and floating bearing NW 17 = 17 mm rail width The smallest type series of the drylin® N series distinguishes itself by the lowest dimensions and high stressing capacity. This series operates free of lubrication and offers the potential to execute high-speed applications. Variants: Standard, Preload (P), floating bearing (LL) extrem low weight Quiet running Installation height 6 mm up to 50 N load NW 17 Preload (with pretension)The NW 17 Preload model of the drylin® N series displays, in addition to the features of the NW 17, an automatic pre-stressing within the rail. Freedom from lubricants and the potential to execute high travel speeds distinguish this series. 1. NW-01-27 standard 01 with through hole g 2. NW-02-27 standard 02 with threaded hole 3. Preload with through-hole or threaded hole 4. uinjection-molded with through-hole or threaded hole 5. NW-21-27-60P Vollkunststoffschlitten mit Durchgangsbohrung 6. NW-22-27-60P solid polymer carriage with through hole 7. NW-11-27-80 double carriage with through hole NW 27 = 27 mm rail width The installation size 27 offers the largest range of various guide carriages. They vary in the connecting potentials, lengths and precision. The injection-molded types additionally facilitate the stocking and installation. NW 27 Preload (with pretension) Identical version to the DryLin® standard carriage NW-01/02-27 and NW-02-40 respectively. The version injection-molded with iglidur® J offers an enhanced installation-friendliness and easier storage for large quantities. Features like the high wear resistance as well as low coefficients of friction remain unchanged. Over 20 carriage options 9.5 mm installation height 100% lubricant-free iglidur® J plain bearing material up to 500 N Last Best selling linear guide DryLin® N - Low profile linear guide system NK-01-27 DryLin® N - Low profile linear guide system NW-21-27-60P DryLin® N - Low profile linear guide system NK-11-27-80 DryLin® N - Low profile linear guide system NK-02-27 DryLin® N - Low profile linear guide system NW-22-27-60P DryLin® N - Low profile linear guide system NK-12-27-80 1. Standard 02 with threaded hole 2. Injection-molded with threaded hole 3. Standard 01 with through hole NW 40 = 40 mm rail width The dimension 40 defines itself by the rail width of 40 mm and ideally fits standard aluminum profiles. The carriages are available with threaded pin or through hole. The gliding elements are available as clip version or directly injection-molded. Lightweight Installation height 9,5 mm high speeds are possible (up to 5 m/s) iglidur® J plain bearing material up to 700 N Last DryLin® N - Low profile linear guide system NK-01-40 DryLin® N - Low profile linear guide system NK-02-40 drylin® N - low profile linear guide system preload NW-01-40P drylin® N - low profile linear guide system preload NW-02-40P 1. Standard 02 with mounting nuts 2. Injection-molded with mounting nuts NW 80 = 80 mm rail width The largest series in the DryLin® N type series offers the potential to take high loads with low installation height. The largest series also operates free of lubrication and can undertake high-speed applications. The gliding elements can be replaced in the clips option, and the injection-molded option facilitates the installation. Installation height 12 mm 100% lubricant-free Wide torque support up to 1000 N Last Gliding elements made of iglidur® J or J200 DryLin® N - Low profile linear guide system NK-02-80 Telescope system Mounting rails: Anodized aluminum Intermediate rail: Plastic Options: Full extension, over extension (+ 20 mm), partial extension Continuous lengths up to 1200 mm extended total length Lubricant-free Low noise Corrosion resistant From stock DryLin® telescopic rails End caps. The new plastic end caps, suitable for DryLin® N rails, offer „protection against loss“ for the carriages and cover the open sharp edges of the profi les safely and in an aesthetic way. Easy installation Low-priced Dismantling possible High retention force DryLin® N end caps Low profile linear axis - SLN-27-01 SLN-27-01: Linear axis for manual operation with hand wheel (SHT-HR-05-22-15-OG) SLN-BB-27-01: Ball bearing linear axis for manual adjustments with hand wheel 100 / 150 / 200 / 250 mm strokes Small (installation height from 22 mm), light and flat Plastic plain bearings in the bearing points Feed with spindle Ø 5 and pitch 0.8 and/or 5 mm Manual and motorized operation drylin® miniature linear axis Low profile linear axis - SLN-27-02 SLN-27-02: Linear axis with NEMA11 stepper motor, ball bearing spindle over motor bearing SLN-BB-27-02: Ball bearing linear axis with NEMA11 stepper motor Small (installation height from 22 mm), light and flat Plastic plain bearings in the bearing points M5-thread (5x0,8 mm), steep thread 5x5 and 6x12,7 Manual and motorized operation drylin® SLN low profile linear axis with motor

Single-phase primary switched-mode power supply in metal housing. Note: Closed version with screw fittings with contact protection. Overload protection due to current limit, auto recovery. Protected against short-circuit, overload and surges. Power on LED indicator. For DIN top hat rail mounting. Technical data: Rating: IP00 Protection class: I Standard: UL508, TUV EN60950-1, CE Connection: screw terminals with contact protection Fastening: installation on DIN rail TS-35/7.5 or 15

Industrial safety railings for mezzanine platforms. To prevent people or objects from falling

Housing steel. Clamping lever plastic. Threaded spindle grade 12.9. Version Housing nickelplated. Clamping lever, spindle black oxidised. Note Manually operated clamping elements for static clamping tasks. Manual clamping process using the freely adjustable clamping lever. The floating clamp ensure symmetrical application of force onto the rail. Up to 50,000 static clamping cycles (B10d value). In general, a friction connection is created between the clamping element and the the linear guide on the open faces of the profile guide rail so that the ball guide tracks are not damaged. The retaining force is tested on an oil smeared profile guide rail. An adapter plate, dependent on the type of carriage used, is required for height adjustment.

Body carbon steel. Balls roller bearing steel. Diverters plastic. Standard guide carriage with recirculating ball guidance precision N not preloaded (Z0). With doublesided end seal. 4row versions with round arch profile. The profile guide rail tracks are arranged at 45° and can accept loads from all directions. High dynamic values v = 5 m/s. Applicable temperature in continuous use max. 80 °C. On request Various precision and preload classes. Drawing reference 1) ground ref. edge

Backstop steel. Axis steel. Cage polyamide, carbonfibre reinforced. Version Electro zincplated Cage black. Note The backstop element is matched to the aluminium profiles for roller rails and can be mounted on them quickly and easily. It prevents reverse movements of items on the roller tracks. No tools required. Suitable for aluminium profiles Type B and I.

Race body steel. Wipers plastic/felt. Longitudinal sealing lips rubber. Rollers steel 1.3505. Note Roller carriage with lifetimelubrication roller bearings and wipers which lubricate the system when moving. By simply moving the centre cam roller, the roller carriage can be adjusted so that it is free of play or has the desired pretension in the rail. High travel speeds up to 7 m/s and extremely quiet (faster and quieter than systems that use recirculating balls). The wipers are fitted with an oilsoaked felt. This felt is in constant contact with the track to ensure perfect lubrication. The felts can be recharged using an oil pump through the lubrication points on the front. On request Roller carriages with 4 or 5 rollers.

Body, extruded aluminium section. Bearing housing and slide, aluminium. Profile guide rail and guide carriage, steel. Toothed belt, polyurethane with steel cord reinforcement. Version Body natural colour anodised Bearing housing and slide, black anodised. Tracks of the profile guide rail, inductively hardened and ground. Note Compact and flexible linear actuators with toothed belt drive. The body consists of a selfsupporting aluminium extruded section with integrated profile guide rail. This rail system is able to absorb highest forces from all directions, is lowwear, and is optimised for moving large masses. Slots are located on the outer sides of the aluminium profile, ensuring easy, reliable assembly and enabling accessories mounted. Proximity switches can be positioned and fastened in the upper Tslot. The aluminium profile is fully compatible with our standard I series profiles.

The aluminium profile is matched to the roller elements. As a result, roller rails and roller tracks can be realised. The different inserts permit modular and flexible setup.

Extruded section, aluminium EN AW6060. Version Hard anodised aluminium, 50 µm. Hardness 500 HV. Note The aluminium guide rail has good thermal conductivity and importantly heats only at continuously very high speeds. ** lengths L2 = 20 mm * and L = 500 mm included L2 and L only available in full mm.

You are planning a facade assembly with our overhead rail transport system and you would like guidance or you have any questions?

These brackets are used to hang aluminium profiles for roller rails in a round profile. A mounting set is supplied.

Ball stainless steel. Housing steel. Cage polyamide, carbonfibre reinforced. These ball transfer units are matched to the aluminium profiles for roller rails and can be mounted on them quickly and easily. For flexible movements in two dimensions. With a lowwear and lowfriction ball rollers. No tools required. Suitable for aluminium profiles Type B and I.

Roller and cage polyamide, glassbead reinforced. Steel axis. Cage black. Roller available in different colours. The roller elements are matched to the aluminium profiles for roller rails and can be mounted on them quickly and easily. No tools required. The compact design with a small centre distance is optimally designed for the lowvibration conveyance of sensitive items. Suitable for aluminium profiles Type B and I.

The aluminium profile is matched to the roller elements. As a result, roller rails and roller tracks can be realised. The different inserts permit modular and flexible setup.

✓ Uninterruptible power supply (DC UPS) with integrated Li-Ion Battery ✓ Intelligent power sharing ✓ Regulated output voltage in backup mode ✓ Minimum load detection ✓ Power fail Timer-Function ✓ Relay dry contact on power fail ✓ USB & RS232 Interface ✓ Plug&Play - recognized as UPS by operating system ✓ Extended functionality by UPScom management software ✓ Shutdown & Reboot Function ✓ Fuel gauge ✓ Approved to IEC/UL/CSA 61010-1 / -2-201 ✓ 3 years warranty The DC UPS UPSI-2406DP1 with included energy storage has been designed for DIN Rail applications. The robust housing protects electronic parts against coarse pollution. The µC-controlled DC-UPS is based on the proven UPSI-technology and features numerous protective and monitoring functions as well as an integrated reboot function, which activates the auto-restart of the computer system, as soon as the input voltage returns during shutdown or later.

✓ Powerful 24 V DC USV (DIN rail version) ✓ Integrated Supercap Pack 13,5kJ ✓ Up to 500 000 cycles ✓ Intelligent input current detection ✓ Regulated output voltage in battery mode ✓ Minimum load detection ✓ Power-fail timer function ✓ Relay dry contact on power fail ✓ Reboot function ✓ Fuel gauge ✓ Shutdown via external signal ✓ Operating temperature range -20°…+70°C ✓ Extended functionality by UPScom management software ✓ 3 years warranty The compact DC UPS modules UPSI-2412DP2 in a robust DIN rail housing are ideally suited for long-term use in control cabinet applications and decentralized solutions for protecting embedded industrial PCs, controls, motor drives, sensors, measurement devices, safety technology and many more. The UPS comes with USB & RS232 interface and provides a capacity of 13.5kJ in up to 500,000 cycles. Extended functionality is available via the UPSGen2 configuration software.

Find out all services on: https://www.europontex.com/wesell.html

We are the best source for ferrous scrap metal and non-ferrous scrap metals. With five recycling locations scattered around EU, and an active demolition and dismantling service we have a huge supply of scrap metal. In addition, we buy scrap metal from national and international customers and resell it to people just like you at affordable prices. As one of the largest scrap metal dealers in the EU, our business, for the past 40 years, has always focused on quality. So while we have a huge supply of scrap metal it is all graded and sorted according to the standards of the metal industry. What that means for you is that when you buy scrap metal you are not just buying a ton of copper, but a ton of copper that is sorted, process and rated according to the standards set forth by the metal industry. We accept a wide variety of ferrous and non-ferrous scrap and surplus metal products.

In ferrous we mainly deal in HMS1 & 2 Material Specification Heavy Melting Scrap (HMS 1& 2) ,80% HMS 1 & 20 % HMS 2 confirming to ISRI 200-206 HMS 1 – ISRI Code 200: heavy melting steel. Wrought iron and/or steel scrap ¼ inch or steel scrap ¼ inch and over in thickness. Individual pieces not over 60 x 24 inches HMS 1 – ISRI Code 201: heavy melting steel 3 feet x 18 inches. Wrought iron or steel scrap ¼ HMS 1 – ISRI Code 202: heavy melting steel 5 feet x 18 inches. Wrought iron or steel scrap ¼ HMS 2 – ISRI Code 203: heavy melting steel. Wrought iron or steel scrap, Black and Galvanized. 1/8 inch and over in thickness, charging box size to include material not suitable as no.1 heavy melting steel. HMS 2 – ISRI Code 204: same as ISRI 203 but max size 36×18 inches. HMS 2 – ISRI Code 205: same as ISRI 204 but free of sheet iron or thin-gauged material. HMS 2 – ISRI Code 206: same as ISRI 204, but max size 60 x 18 inches.

Telescopic rail 27.2 x 20 mm, stainless steel, standard lengths up to 600 mm, load capacity up to 35 kg per pair Ball bearing over-extension Load capacity up to 35 kg per pair Standard rail length up to 600 mm Closed end stop Operating temperature up to +200°C Manufactured in the European Union For over 40 years, the Schock Group has been developing and manufacturing ball bearing telescopic rails for linear motion technology. The advantageous physical properties of ball bearing guidance form the basis for the performance of Schock telescopic rails: Smooth and quiet operation, even under high load High functional reliability Long service life without maintenance

Telescopic Rail 57.5 x 17.5 mm, galvanized steel, standard lengths up to 750 mm, load capacity up to 80 kg per pair. This telescopic rail from the Schock Group is designed for over-extension with a 100%+ extension range, making it ideal for applications where full access to the drawer or component is necessary. It is made from galvanized steel and offers a load capacity of up to 80 kg per pair, making it suitable for heavy-duty applications. Key Features: Telescopic Rail Type: Over-extension Material: Galvanized steel Standard Lengths: Up to 750 mm Load Capacity: Up to 80 kg per pair Locking Mechanism: Included Manufactured in the European Union Schock Group has over 40 years of experience in designing and manufacturing ball-bearing telescopic rails for linear motion technology. Their telescopic rails are known for their smooth and quiet operation, even under high loads, as well as their reliability and long service life without the need for maintenance.