Anchoring system - Import export

Ground anchors, ground screws or screw anchors are used in various applications, such as: Stable earth screw foundation: Perfect solution for garden sheds, gazebos, greenhouses, patios and carports, for permanent or temporary applications (reusable, as long as not damaged), can be loaded immediately even in winter Bracing of poles: Ground anchors are used to securely anchor masts to the ground and to absorb tensile forces. This is particularly important in situations where where high stability and safety are required, for example installation of antenna masts or for temporary constructions constructions such as event stages. Recovery of vehicles: Ground anchors can be used as anchor points to secure vehicles during recovery or rescue operations. rescue operations. They provide a reliable anchorage in the ground to absorb tractive forces and allow safe towing or towing or moving vehicles off-road.

This expansion joint is suitable to absorb longitudinal and transverse displacements of the decks with span up to 25 metres and covering gaps of up to 50 mm. It consists of: • anchoring system consisting of steel anchor clamps (anchor rods) of suitable dimensions and section; • CNR 10018/85-compliant reinforced rubber elements, to be fixed to the slabs, consisting of central bridging plate and two steel bearing elements, subject to prior laying of epoxy resin bedding; • hypalon gutter, fixed to the two slab heads by epoxy plaster. POS. DESCRIPTION MATERIAL A Gap-covering plate Dielectric vulcanized rubber B M12 anchoring system C Gutter Hypalon D Pouring of modified bitumen E Epoxy plaster S Fip 180 F Restoring of base plane Fibre-reinforced cement mortar G Binder H Road surface

llength of modular element = 1000 mm POS. DESCRIPTION MATERIAL A Transition strip EPOBLOCK ME 3C B M20 Anchoring system C Gutter Hypalon D "L"-shaped drainage profile " X5 CrNi 1810-UNI 8317 E Sleeding sheet X5 CrNi 1810-UNI 8317 F Sealant EPOBLOCK ME Granulate

length of modular element = 1000 mm POS. DESCRIPTION MATERIAL A Transition strip EPOBLOCK ME 3C B M20 Anchoring system C Gutter Hypalon D "L"-shaped drainage profile X5 CrNi 1810-UNI 8317 E Sleeding sheet X5 CrNi 1810-UNI 8317 F Sealant EPOBLOCK ME Granulate

Expansion joint made of: CNR 10018/85-compliant modular reinforced rubber pads consisting of two plates vulcanized to a rubber gap cover of seal and disposal of surface waters; mechanical anchoring system made of steel rawl bolts or multidirectional clamps and anchor rods or threaded bars, depending on site requirements; hypalon gutter; "L"-shaped stainless steel profile for under pavement waters drainage; epoxy mortar strips connecting the joint elements and the bituminous pavement. POS. DESCRIPTION MATERIAL A Sealant EPOBLOCK ME Binder B Transition strip EPOBLOCK ME 3c C Mortar bedding FIBER-REINFORCED CEMENT MORTAR D M12 Anchoring system E Gutter Hypalon F "L"-shaped drainage profile X5 CrNi 1810-UNI 8317

Expansion joint made of: • CNR 10018/85-compliant modular reinforced rubber pads consisting of a central bridging plate and side bearing elements vulcanized to steel plates; • mechanical anchoring system consisting of threaded bars or, as an alternative, multidirectional clamps and anchor rods, depending on site requirements; • hypalon gutter; • "L"-shaped stainless steel profile for under pavement waters drainage; • epoxy mortar strips connecting the joint elements and the bituminous pavement. JOINT TYPE TOTAL MOVEMENT (mm) HEIGHT H(mm) WIDTH X(mm) GAP Y(mm) ANCHORS Z(mm) GPE 50 50 42 250 *35 75 GPE 100 100 56 366 *60 115 GPE 150 150 83 555 *85 190 length of modular element = 2000 mm
 * average gap POS. DESCRIPTION MATERIAL A Sealant EPOBLOCK ME Granulate B Transition strip EPOBLOCK ME 3C C M16 Anchoring system D Gutter Hypalon E "L"-shaped drainage profile " X5 CrNi 1810-UNI 8317

Railway expansion joint rail with water-proof and dielectric characteristics suitable to absorb longitudinal movements of the decks from 100 to 450 mm and vertical deformations up to ± 50 mm. This type of joint is designed to prevent the ballast penetration in the gap or in any active part of the joint. The RFI-approved series (built according to instruction 44/e) is for displacements from I 00 to 250 mm. Consisting of: • CNR 10018/85-compliant reinforced rubber dielectric modular pads consisting of a central bridging plate and two side elements; • mechanical anchoring system consisting of threaded bars fixed with epoxy resin; • stainless steel protection and sliding plates; • hypalon gutter; • side draining slats for under-ballast infiltration waters; • epoxy mortar transition strip between the joint and the binder. To complete the Beta railway joint the sidewalk and ballast joint is available, consisting of: • reinforced dielectric rubber flange: flat for the sidewalk and shaped fo

Original RAN P expansion joint suitable to absorb displacements of the decks up to 1000 (mm) as well as relative rotations between consecutive slab heads and their relative movements both in the vertical and transverse direction consisting of: • CNR 10018/85-compliant modular reinforced rubber pads consisting of a central bridging plate and two side bellows equipped with anti-lift bar, free to move along stainless steel plates, assembled in situ; • mechanical anchoring system consisting of threaded bars or, as an alternative, multidirectional clamps and anchor rods, depending on site requirements; • stainless steel gutter; • "L"-shaped stainless steel profile for under pavement waters drainage; • epoxy mortar strips connecting the joint elements and the bituminous pavement. JOINT TYPE TOTAL MOVEMENT (mm) *X (mm) Y (mm) BRIDGE P. (mm) BELLOWS RAN P 400 400 55 760 220 DOUBLE + SINGLE RAN P 500 500 65 890 270 DOUBLE + DOUBLE RAN P 600 600 75 1040 320 DOUBLE + DOUBLE RAN P 700 700 85

Many times blind noise barriers heavily affect the environment by changing, some times for the worst, visual perception; the fitting of wide clear barriers, in addition to breaking monotony and allowing the landscape to be seen, remarkably mitigates the environmental impact of the barrier. TECNOWALL clear panels significantly improve the appearance of deteriorated landscapes, with the fitting of mass-coloured or especially made panels. Examples of anchoring systems However the material that is more frequently used is polymethyl methacrylate for its clear and quick-handling features. The TECNOWALL clear panel is fixed to the bearing structure by a suitable frame hot-galvanized steel and painted frame; the sheet is surrounded by a rubber seal that is resistant to weathering agents, shaped so as to follow thermal-expansion-induced movements of the sheets. The polymethyl methacrylate sheets used can be hot- and cold-thermoformed so as to take on the shapes as requested by Customer or su

GP-type steel finger joints suitable to absorb deck displacements of up to 250 mm (+ I 25) consisting of: • anchoring/support system made of patented anchor rods of suitable section and length; • suitably dimensioned and shaped stainless steel gutter. • active upper part consisting of an overhung metal finger system obtained by the processing of COR-TEN steel plates equipped with bolts, nuts, washers etc.; • under-pavement waters drainage consisting of stainless steel "L"-shaped profile. JOINT TYPE TOTAL MOV. (mm) HEIGHT H (mm) WIDTH*X (mm) GAP *Y (mm) ANCHORS Z (mm) ANCHORS T (mm) ANCHORS ø (mm) GP 50 50 30 400 60 80 45 M16 GP 100 100 30 470 80 105 45 M16 GP 150 150 35 545 105 130 45 M20 GP 200 200 40 620 130 155 45 M24 GP 250 250 45 820 155 180 45 M24 Length of finger element = 480 mm * average gap POS. DESCRIPTION MATERIAL A Finger element S355J2WP EN 10025 B Sealant EPOBLOCK ME Legante C Transition strip EPOBLOCK ME 3C D Bedding EPOBLOCK ME 3C / Beton FIP E Anch