Aluminium housings - Import export

Housing aluminium. Cable sheath PVC. Version Compact sensor and plug design. Flat connector, 8pole, 1x pin. Connection cable, 6wire, ø 3.55–0.3 mm. Cable bend radius, > 17 mm (static). Note Works with magnetic tapes 21725. The reading distance between the sensor and tape must be 0.1 to 2 mm. The sensor is supplied with operating voltage and draws current via the electronics. System accuracy, repeat accuracy and travel speed is dependent on the electronics. Plugin connection to position indicators 21700 and 21702. Technical data Rating IP 67; EN 60529 (sensor head) Shock resistance 2000 m/s², 11 ms; EN 60068227 Vibration resistance 200 m/s², 50 Hz–2 kHz; EN 6006826 Temperature range Ambient temperature 0…60°C Storage temperature 10…70°C Assembly Installation must be carried out using the enclosed user information. A, reading distance sensor/tape ≤ 2 mm B, lateral offset ± 2 mm C, misalignment ± 3° D, pitch gradient ± 1° E, lateral gradient ± 3°

The readytoinstall compact linear housing consists of extruded aluminium housing, installed linear ball bearing 2151102 and doublesided seal. Recommended shaft tolerance h6. Load rating according to specification of the linear ball bearing. With lubrication hole M8x1. Accessory Precision guide shafts 21595. Fastening screws 07160.

The PULSAR H is a fully automatic, horizontal-operating rotary laser with an easy-to-use operating concept. If vibrations or shocks occur, the laser automatically interrupts the rotation, preventing measurement errors. The robust aluminum housing and high-quality workmanship make it ideal for tough use.

Housing, steel. Magnetic core AlNiCo. Hard magnet in aluminium housing and steel jacket. Shielded system. Pot magnets are used for retaining, lifting and mounting in fixtures. Due to the painted surface, the diameter D can be up to +0.8 mm.

Housing aluminium. Precision tube nickel plated steel. Trapezoidal thread spindle steel. Note The doubletube linear actuator can be operated manually or electrically. Due to the short duty cycle, the units can be adjusted several times a day at low speed and with high stability. Width, length and height adjustment possible.

Body, extruded aluminium section. Bearing housing and slide, aluminium. Profile guide rail and guide carriage, steel. Toothed belt, polyurethane with steel cord reinforcement. Version Body natural colour anodised Bearing housing and slide, black anodised. Tracks of the profile guide rail, inductively hardened and ground. Note Compact and flexible linear actuators with toothed belt drive. The body consists of a selfsupporting aluminium extruded section with integrated profile guide rail. This rail system is able to absorb highest forces from all directions, is lowwear, and is optimised for moving large masses. Slots are located on the outer sides of the aluminium profile, ensuring easy, reliable assembly and enabling accessories mounted. Proximity switches can be positioned and fastened in the upper Tslot. The aluminium profile is fully compatible with our standard I series profiles.

✓ Outdoor AC/DC UPS for extreme environments in robust aluminium housing with IP65 protection ✓ Already integrated LiFePO4 energy storage (330 Wh) ✓ Temperature range -20…+50 °C ✓ Intelligent input current regulation ✓ Regulated output voltage in battery mode ✓ Pressure compensation element to prevent condensation inside ✓ Input and output cable firmly installed ✓ IEC/EN 62040-1 certified ✓ Optionally available: mounting sets for masts AC-DC UPS with IP65 protection class for outdoor applications The UPSI-2406IP-38AC is an AC/DC UPS system with numerous digital features and a high performance. The UPSI-2406 is used with an upstream AC/DC converter and combined with an already integrated LiFePO4 energy storage. The primary use of the UPS is in bridging power failures and/or fluctuations. The application to be protected is connected to the output of the UPS. The device has IP65 protection and was specially designed for use under extreme conditions.

Spirit levels are tools commonly used in construction, woodworking, and other fields where accurate leveling is important. They consist of a straight bar or tube filled with liquid (usually alcohol) and a bubble. When the bubble is centered between two lines marked on the tube, it indicates that the surface being measured is level. The Ronix RH-9417 spirit level is simple and easy to use, requiring no batteries or AC power. It is compact and lightweight, making it easy to carry and use in tight spaces. It also features level bubbles that accurately measure horizontal, vertical, and 45° tilt angles. The level is durable and impact resistant due to its aluminum housing. Plus, this practical hand tool is easy to read with clear, visible level bubbles.

spindle end housing manufactured by CNC turning and milling 4 thread holes chamfered on both sides, thread grade M3.0 free of burrs cap end external diameter: 30.50 +0.05/-0.00 mm bottom end external diameter: 14.60 +0.10/-0.05 mm height: 17.50 +/- 0.03 mm material: aluminum alloy ASTM 6061-T6 With sliding head multi-axis CNC lathes, we are capable of producing complex parts requiring turning, milling, drilling, tapping, broaching etc in one setup.

*Aluminum die-cust housing, with aluminum die cust handle *Electric switch with 6 speed *LCD display showing working time, speed and power level *Aluminum gear box and full metal gears *12 head with large metal food tray *Copper motor, 2000W locked power *Power: 2000W, *220-240V, 50/60Hz, within 90dBA, VDE plug *1 stainless steel cutting blade *Three life time cutting plates *Kibbeh attachments *Sausage adapter *Food pusher

The LF-TA transmitter of Schaller measurement instrumentation, with its robust and easy to mount aluminium housing, is best suited for all applications in this field. For temperatures of up to 60°C for laboratory, climate control and drying technology, wood processing industry, food and animal feed industry, building industry, printing and paper industry, agriculture, biotechnology and pharmaceutical industry.

Extruded Stator housings made of aluminium frame 56 to 132 for individual drive solutions such as servo-motors, circular saws or - if required - extra long housings. Available from existing stocks are various profiles at a length of 3000 mm or cut to customized length.