Sensors - Import export

The PPS Aerostrip provides a simple and convenient replacement for traditional pressure tapping or pressure-sensitive paint. It is a low profile, rapidly deployable air pressure sensing strip for aerodynamic measurement and surface optimization for motorsport and aerospace applications. The AeroStrip consists of an extremely thin strip of sensors that can be applied, and reapplied, non-destructively to test surfaces for pressure measurement due to reusable masked adhesive backing. It has comparable accuracy to pressure tapping in subsonic flow, but with a tiny fraction of the setup time and cost. With Aerostrip, you can quickly take non-destructive outside pressure measurements from control surfaces, live or in a wind tunnel, enabling faster turnaround and optimization of aerodynamic components.

The PPS Wrist Sensor is designed to be worn on the wrist and provides accurate capture of pressures exerted on the wrist. This thin, fabric-like sensor offers a minimally-invasive method for measuring the contact pressure of any device or product worn on the wrist. Use this to map and measure the comfort of watch bands, wristbands, activity trackers, and more. Identify areas of high-pressures or discomfort, and improve your product in a quantitative, measurable way. The wrist sensor can be used in motion to characterize pressures during movements, such as when jogging.

The TactileMat is a rigid and robust pressure sensing pad that is of the largest, high-resolution pressure mapping sensors on the market. The use of a large area sensor like the TactileMat allows you to capture dynamic pressure over a larger area without the dead zones typically associated with trying to use multiple smaller sensors side-by-side. This is one of the largest pressure mats on the market. Key Features Large pressure mapping surface area (220 mm x 450 mm) Rigid, robust, and can be built in various full scale ranges (FSR) up to 188 psi FSR Waterproof IP53+ (Can be special ordered to higher water-proofing upon request) Slim construction (7.69 mm) with a non-slip base Array Size = 44 x 90, element size = 5 mm x 5 mm

A sensitive, waterproof capacitive tactile sensor array designed to capture instantaneous and actionable spray pattern and spray pressure data generated by sprayed fluids or gases. Capture spray distribution and impact pressure and accurately identify the location and pattern where sprayed fluid or gases land. Available in two application variants, Spray Pressure or Spray Pattern, and optimal for use in situations where spray pressures are infinitesimally small.

The Stretchable TactArray is a flexible pressure sensor pad engineered from a soft and conductive silver-metalized Spandex. The Stretchable TactArray can stretch up to 10% and be folded in multiple directions while still maintaining high data quality. This sensor is approximately 3-7 mm thick and is best suited for dynamic curvature applications such as seats, horseback saddles and other applications where sensor thickness is not an issue. Key Features Stretch this sensor up to 10% while maintaining accurate data Can be used on objects with dynamic, multi-directional curvature (e.g., heads, spheres, computer mouse) Ideal for applications where the sensor will be flexed or deformed through use, such as seat cushions, mattresses, or clothing Capture high quality pressure data between pressures of 5 psi to 50 psi and within temperature ranges of –20° to 50°C Comes standard with Chameleon Visualization Software, and is available in many sizes and configurations

The Industrial TactArray is a flat sensor that can capture and map pressure distribution in even the most extreme conditions. Constructed from high-quality Kapton or Polyimide, the Industrial TactArray can pressure distribution of up to 700 psi and in temperatures between -40° C and 200° C. This system is best suited for use in applications requiring tactile sensors that can withstand extremely high temperatures and pressures—like heat presses, brake pads, and nip rollers. Key Features High-resolution sensor arrays can measure pressure distribution at levels of up to 700 psi and retain performance characteristics in temperatures between -40° C and 200° C Real-time thermal compensation ensures accurate measurements even under changing temperature conditions Ultra-thin construction, 0.3 mm thick, and high-resolution sensing elements Can accommodate moderate flexing and bending Available in multiple sizes and configurations Chameleon Visualization Software included

The Conformable TactArray is a ~1mm thick flexible sensor constructed from soft, conductive cloth and captures pressure distribution between two objects in direct physical contact. The Conformable TactArray can accommodate varying degrees of curvature and can output accurate, repeatable data even while wrapped around irregular shapes. Key Features and Benefits: Maintain high-resolution and capture quality data even around complex shapes High resolution, sensitivity, and repeatability allow for consistent capture of accurate data The sensors can capture a minimum sensing pressure of 10 Pascal Save time and improve results through repeatable accuracy and less recalibration time needed Available in a wide range of size configurations, pressure ranges, and resolutions Comes standard with the powerful Chameleon Visualization Software

The PPS TactileGloves are tactile pressure sensor gloves with embedded sensing elements throughout the palm and fingers, allowing for natural and accurate testing of pressures applied to and exerted by the hand. Nearly any hand operation can be measured accurately through the 65 individual highly sensitive sensing elements within each glove. Sensor Glove Features: Ensure a natural test environment with the only glove hand sensor on the market User friendly, comfortable to wear and no adhesives or wires to get in your way High-resolution, sensitive sensors detect even the lowest pressures (0.1oz/3g) Meant to handle the real world. It's wireless and battery powered. Delivered in pairs (Left + Right). Available glove size: small, medium, and large.

The FingerTPS is a set of wearable finger sensors that enable you to measure grip, touch, and other hand forces. A more affordable alternative to the TactileGlove, this easy-to-use system captures high-quality data in a natural and organic form-factor. **Finger selection can be customised to specification** Features: Design or research with accurate, sensitive and repeatable data even for complex finger geometry. Comfortable and minimally-intrusive system allows for full range of motion and ensures natural hand manipulation research. Plug and play—no configuration needed. Just place on the hand, calibrate the sensors and Chameleon auto-detects your hand configuration. Compact wireless Bluetooth electronics provides simple and easy to use set-up, with minimal wires. Connect two wrist assemblies at the same time for two handed operations.

The CTA TactileHead is a width adjustable pressure measurement and mapping system for quantifying pressures exerted by headphones, earmuffs, headbands, and more on various head sizes. A high-resolution Conformable TactArray sensor is molded onto the curved area around the ear of the mannequin head, while another high-resolution TactArray sensor is mounted to a flat plate on the other side of the head to provide a controlled comparison. Chameleon, our real-time visualization and acquisition software, is then used to display pressures from both sensors simultaneously and to perform real-time analysis for evaluating comfort and fit.

This is a calibrated pair of a SingleTact sensor and USB electronics board. It comes with 50 cm USB cable and a Calibration sheet. We have various combinations of sizes and pressure ranges, please select a sensor that meets your criteria. A handy Help Me Choose page can assist you with the selection. The sensor and electronics are a matched pair, the calibration is stored on the electronics. You can use a tail extender with calibrated systems, but not interchange with other sensors.

This is a calibrated pair of a SingleTact sensor and I²C electronics board. It comes with 4 jumper wires and Calibration sheet. We have various combinations of sizes and pressure ranges, please select a sensor that meets your criteria. A handy Help Me Choose page can assist you with the selection. The sensor and electronics are a matched pair, the calibration is stored on the electronics. You can use a tail extender with calibrated systems, but not interchange with other sensors.

Digi-Pas® DWL5000XY Series is a 2-Axis Inclination Sensor Module that specifically designed to be integrated into a machine/equipment/ structure for real-time simultaneous monitoring of leveling position, tilt angles & vibration measurement. These intelligent modules are embedded with advanced MEMS technology sensor, developed for 2D planar leveling, tilt angle monitoring, alignment and vibration measurement. The 'plug & play' software interface instantly enables application engineers to access sensor modules without the need for tedious and time-consuming programming. Sensor modules are tough, durable, waterproof, shock resistance, small footprint and enabled to communicate through various protocols such as USB, RS232, RS485 & Bluetooth. Digi-Pas® DWL-5000XY is a 2-Axis Precision Inclination Sensor Module of accuracy (0.01° or 175µm/M or 36 arcsec) Digi-Pas® DWL-5500XY is a 2-Axis Precision Inclination Sensor Module of accuracy (0.001° or 18µm/M or 3.6 arcsec)

The RoboTouch patented capacitive tactile sensing technology is the highest performance embedded tactile sensing technology for giving industrial and consumer robotic grippers or Humanoid robots the “sense of touch”. It is based on Digitacts sensor technology that features embedded digital output ideal for OEM integration into the gripper. The sensors comprise of multiple sensing pads, each typically with 12-24 sensing elements, which can be placed on any location of choosing in the gripper. Data from sensors are transferred to grippers via I²C or SPI digital interfaces, enabling you to easily integrate the sensors into your grippers.

We have been an innovator and partner to numerous successful medical projects over the past 20 years. Our patented technology enables new possibilities in the medical space, and our team has the experience and expertise to effectively integrate tactile sensing for breakthroughs in medical advancement. Whether you are looking to simply integrating our sensors for data capture, or looking for an agile, knowledgeable partner to take you from concept to creation, we’re here to help. Examples: PULSE DEVELOPMENT KIT - Measure and analyze pulse waveforms SURETOUCH - An FDA approved, radiation-free, breast lesion detection system MANOSCAN - A high-resolution esophagus catheter WRIST-AID - A non-invasive carpal-tunnel-syndrome treatment device

The affordability of SingleTact standard force sensors makes them a great place to start. Measuring capacitance can be challenging so we advise that you use our electronics board to provide a convenient voltage output and a digital I²C interface. We have various combinations of sizes and pressure ranges, please select a sensor that meets your criteria. A handy Help Me Choose page can assist you with the selection.

DWL-2000XY, DWL-3000XY & DWL-3500XY are 2-Axis precision Digital Levels with high accuracy and wide measuring range of levelling, angle, alignment & vibration measurements, capable of real-time remote USB/wireless measurement & data logging. The accuracy performance is verified by accredited calibration & test bodies in USA, Japan & Germany traceable to NIST, JIS & DIN. These instruments are exceptionally engineered to greatly simplifying the task of precision engineering professionals & tradesmen in installation, setting up & maintenance of very high precision CNC machines, test instruments & alignment-sensitive equipment.