Transformation unit - Import export

Single-phase primary switched-mode power supply in metal housing. Note: Closed version with screw fittings with contact protection. Overload protection due to current limit, auto recovery. Protected against short-circuit, overload and surges. Power on LED indicator. For DIN top hat rail mounting. Technical data: Rating: IP00 Protection class: I Standard: UL508, TUV EN60950-1, CE Connection: screw terminals with contact protection Fastening: installation on DIN rail TS-35/7.5 or 15

REVEX PA is the latest born in the REVEX family. The REVEX are positioned between the two families REVO S and REVO C in terms of price and performance. The main characteristic is that they can be configured according to your needs by eliminating of all options that you do not want to use, in order to reduce the purchase price. It is an extremely flexible and performing unit. The REVEX PA is a three-phase unit with higher functions compare to the other REVEX 3PH models, because it is able to carry out phase angle firing with or without Current Limit. REVEX PA is therefore a unit suitable for driving inductive loads, such as three-phase transformers. The algorithms inside the unit allow the control of the power even for special loads, such as MoSi2 and SiC heating elements. It is suitable for controlling both normal resistive loads and short, medium or long wave infrared lamps.

The REVO RT is a compact power controller unit, which integrates inside a single phase static group for each loop for control of the electrical power. Each unit manages 3 independent control loops. The unit can be purchased with the diagnostic functions for the load and for the SCRs. In this case there is a amperometric transformer for each channel. Each power channel is always equipped with extra rapid fuses . The power inside the unit, current transformer and extra rapid fuses in a single unit save a considerable space inside the panel and time for wiring . Available in the following currents: 35, 50, 75 and 90A with maximum voltages 480V and 600V.

The Cleanflex Easy ionising air gun can be used for cleaning and neutralising surfaces. It’s unique features, not seen in any other ionising guns, make it very versatile to use. Ergonomic, hand or pull down, less air consumption, low noise, better blow-off force. - 24V DC input voltage and integrated ionisation power unit The Cleanflex Easy has a 24V input voltage, easily connect by a standardised M12 connector. No cumbersome high voltage cable and big transformer unit as seen in traditional ionisation guns. - Lightweight A Durable plastic housing and a well-constructed weight distribution make it a well balanced comfortable gun to use. - Ergonomic design The grip has been designed to suit women’s as well as man’s hands and has a soft grip and grip fixation making it very easy to hold without any muscle tension. - Full hand trigger (no RSI strain on one finger) The air flow is controlled with a full hand trigger, making operation very comfortable.

Product Features: • A perfect match to the 1650P Series Potted Output transformers. • Enclosed in a drawn steel case, the transformer is completely potted in epoxy. • Mounting hardware included. • Primary: Universal - 100, 110, 120, 200, 220, 240 VAC 50/60 Hz. • Bias Tap: 50 VAC tap from high voltage secondary C.T. • Highpot tested: 2,000 VAC. • Faraday Copper Primary Shield: The electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell). • Windings: Concentric wound for low stray field and low noise. • Finish: Black powder paint to match the 1650P Series of potted output transformers. • Units can be run full wave bridge or full wave C.T. • c UL us recognized (E207860).

Product Features: • Enclosed, 4-hole mount chokes (some models also available epoxy potted in a black powder paint - drawn steel housing. Potted models mount with 1/4" - 20 hardware (included). • Tolerance of 15% on both inductance and resistance. • Inductances measured at rated D.C. current. • Minimum 8" long leads. • Units will exhibit less inductance at slightly higher currents or more at lower currents. • Perfect for high voltage power supply filtering, case matches power transformers and tube audio output transformers. • Units are vacuum impregnated with polyurethane varnish for quiet and long life operation. • Operating temperature range is -40C to 85C. • Proper Henry testing requires an LCR meter in junction with a 25A power supply that does allow for DC bias as well a higher applied AC drive voltage to meet the test specifications.

The unit is designed to measure the dielectric strength of transformer oil and other dielectric fluids according to IEC 60156, ASTM D877, ASTM D1816. It is a fully automatic device - allows testing according to the procedures defined in these standards, as well as according to the user procedures specified in the appropriate section of the setup menu. The core of the unit is the high voltage transformer and electronic modules. The unit operates by gradually increasing the voltage on the secondary winding of the high voltage transformer from zero to the maximum voltage, or to the voltage at which an electric breakthrough occurs in the dielectric fluid in the measuring cell installed on the high voltage contacts of the transformer. During operation, AC (50-60Hz) voltage is supplied from the secondary winding terminals through the cell electrodes into the dielectric fluid in the measuring cell.

GlobeCore manufactures oil regeneration systems for both transformer manufacturers and for transformer service providers. GlobeCore units are loaded with a sorbent that captures all oil decomposition products. GlobeCore regeneration systems can use the same sorbent for up to 3 years before the first replacement. No more need for consumables and costly labor related to replacement of exhausted sorbent on the job site. Regeneration systems can be combined with degassing units or can be purchased as stand-alone systems. GlobeCore regeneration systems can be used in combination with your existing degassing or drying unit. Each GlobeCore unit can be customized and includes a number of options: An extra vacuum pump assembly for transformer vacuuming Mounted on a trailer or a semi-trailer Inlet and/or outlet moisture meters for the oil stream Remote control and process monitoring via smartphone or PC Climate Controlled Operator work room.

New Controller with Universal Design. Small size, More floor space, and Saving Energy.Kawasaki has incorporated more than 45 years of experience as a robot industry leader into the development of the most technically advanced controller available. The E0X controllers are standard for world-wide use and available for multiple primary power supply voltages with a separate transformer unit. Achieve extremely compact design, compared to E2X/3X/4X controllers. The E03 controller, for use on palletizing robots, has an electricity regeneration function that reduces energy consumption.