Tapered edge - Import export

TECHNICAL DEFINITION CE 78 PERFECT’LIGHT is a ready-to-use lightweight jointing compound specially formulated for tapered-edge plasterboards, to be used with joint tape. COMPOSITION AND APPEARANCE Resin, water, calcium carbonate, lightening fillers, preservative and various admixtures. The compound is white. SUITABLE SURFACES All types of tapered-edge, paper-lined plasterboard, with or without insulation. TECHNICAL CHARACTERISTICS • Tape adherence : > 1000 g • Cracking : no cracking up to a thickness of 5 mm APPLICATION Before treating the joints themselves, any gaps where the plasterboards are accidentally out of alignment must be filled, along with any other gaps Apply the product manually, spreading the diluted mixture for 10 or 15 cm with a coating knife before applying the tape (with the rough side against the coating). Then apply a finishing layer, leave to dry and finish to hide the tape and screw heads. In the event of projecting vertical angles, use reinforced tape.

SUITABLE SURFACES All types of tapered-edge, paper-lined plasterboard, with or without insulation (glass wool, rock wool, polystyrene). COVERINGS First undercoat for plasterboard. Smoothing compound. PACK SIZE Tubs of 5 and 25kg on covered pallet. STORAGE 9 months in unopened original packaging, away from frost and extreme heat. AMOUNT REQUIRED Approximately 500 g/m² of plasterboard. DRYING TIME The second coat can be applied 24-48 hours after the first, depending on the ambient conditions. RECOMMENDED APPLICATION Always leave a minimum gap of 20 cm between doors and windows and the first plasterboard joint.

TECHNICAL DEFINITION Ready-to-use coating paste coating specially formulated for use on tapered-edge plasterboard joints, to be used with jointing tape. The coating comes mixed : it is suitable for gluing and finishing the tape. COMPOSITION AND APPEARANCE Resin, water, calcium carbonate, preservatives and various additives. The paste is white in colour. TECHNICAL CHARACTERISTICS Cracking : Up to 5mm thickness with no cracking. APPLICATION Application is carried out manually, spreading the thinned the product with a coating knife across 10 or 15 cm, before laying the tape in position. In the event of projecting vertical angles, use reinforced tape (frame placed at the side of the panel). Apply tape to the internal ceiling corners, making sure that the concrete is free of any trace of forming oil. The surface must be dry and free of any type of powder or insufficiently adherent product.

COMPOSITION AND APPEARANCE Resin, water, calcium carbonate, lightening fillers, preservatives and various adjuvants. The resulting paste is white in color. SUBSTRUCTURES ADMITTED All types of plasterboard with or without insulation with tapered edges and cardboard faces. COATINGS Printing undercoat for gypsum plasterboard. Smoothing coating. TECHNICAL CHARACTERISTICS - Adhesion of the tape: > 1000 g - Cracking: no cracks up to 5 mm thick - Density: 1.2 STORAGE 9 months in original unopened packaging, protected from frost and heat. APPLICATION Before treatment of the joints themselves, the panels must be filled between accidentally non-joined panels and various fillings). The application is done manually by "buttering" the thinned panels with a 10 or 15 cm coating knife and placing the strip in place. Then carry out a finishing pass, let dry and finish to mask the strip. For vertical protruding corners, use a reinforced strip or a metal angle iron.

COMPOSITION AND APPEARANCE Powder coating based on plaster, calcium carbonate, resin, and various additives. SUBSTRUCTURES ADMITTED All types of plasterboard with or without insulation with tapered edges and cardboard faces. COATINGS Printing undercoat for gypsum plasterboard. Smoothing coating. TECHNICAL SPECIFICATIONS - Adhesion of the tape: > 1000 g - Cracking: no cracks up to 5 mm thick - Density: 1.7 - Reaction to fire: A2s1d0 MIXING RATIO 10 to 11 liters of water per 25 kg bag. APPLICATION Before treatment of the joints themselves, the panels must be filled between accidentally non-joined panels and various fillings The application is done manually by "buttering" the thinned panels with a 10 or 15 cm coating knife and placing the strip. Then carry out a finishing pass, let dry and finish to mask the strip. Also mask the screw heads. Apply a strip by picking up the ceiling, making sure that the concrete is free of any trace of form oil.

COMPOSITION AND APPEARANCE Powder coating based on plaster, calcium carbonate, resin, and various additives. The paste obtained is white in color. SUBSTRUCTURES ADMITTED All types of plasterboard with or without insulation with tapered edges and cardboard faces. COATINGS Printing undercoat for gypsum plasterboard. Plaster-based smoothing plaster. TECHNICAL SPECIFICATIONS - Setting time: setting by drying - Adhesion of the tape: > 1000 g - Cracking: no cracks up to 5 mm thick - Density: 0.8 STORAGE 9 months in original unopened packaging protected from humidity. MIXING RATIO 10 to 11 liters of water per 25 kg bag. APPLICATION Before treatment of the joints themselves, the panels must be filled between accidentally non-joined panels and various fillings The application is done manually by "buttering" the thinned panels with a 10 or 15 cm coating knife and placing the strip. Then carry out a finishing pass, let dry and finish to mask the strip. Also mask the screw heads.

COMPOSITION AND APPEARANCE Powder coating based on plaster, calcium carbonate, resin, and various additives. The paste obtained is white in color. SUBSTRUCTURES ADMITTED All types of plasterboard with or without insulation with tapered edges and cardboard faces. COATINGS Printing undercoat for gypsum plasterboard. Plaster-based smoothing plaster. TECHNICAL SPECIFICATIONS - Setting time: 8 hours - Adhesion of the tape: > 1000 g - Cracking: no cracks up to 5 mm thick - Reaction to fire: A1 STORAGE 9 months in original unopened packaging protected from humidity. MIXING RATIO 10 to 11 liters of water per 25 kg bag. APPLICATION Before treatment of the joints themselves, the panels must be filled between accidentally non-joined panels and various fillings. The application is done manually by "buttering" the thinned panels with a 10 or 15 cm coating knife and placing the strip. Then carry out a finishing pass, let dry and finish to mask the strip. Also mask the screw heads.

COMPOSITION AND APPEARANCE Powder coating based on plaster, calcium carbonate, resin, and various additives. SUBSTRUCTURES ADMITTED All types of plasterboard with or without insulation (glass wool, rock wool, polystyrene) with tapered edges and cardboard faces. COATINGS Printing undercoat for gypsum plasterboard. Plaster-based smoothing plaster. TECHNICAL SPECIFICATIONS - Setting time: 4 hours - Adhesion of the tape: > 1000 g - Density: 0.9 - Reaction to fire: A1 STORAGE 9 months in original unopened packaging protected from humidity. RATE OF MIXING 10 to 11 liters of water per 25 kg bag. APPLICATION Before treatment of the joints themselves, the panels must be filled between accidentally non-joined panels and various fillings. The application is done manually by "buttering" the thinned panels with a 10 or 15 cm coating knife and placing the strip. Then carry out a finishing pass, let dry and finish to mask the strip. Also mask the screw heads.

COMPOSITION AND APPEARANCE Powder coating based on plaster, calcium carbonate, resin, and various additives. The paste obtained is white in color. SUBSTRUCTURES ADMITTED All types of plasterboard with or without insulation (glass wool, rock wool, polystyrene) with tapered edges and cardboard faces. COATINGS Printing undercoat for gypsum plasterboard. Plaster-based smoothing plaster. TECHNICAL SPECIFICATIONS - Setting time: 2 hours - Adhesion of the tape: > 1000 g - Cracking: no cracks up to 5 mm thick STORAGE 9 months in original unopened packaging protected from humidity APPLICATION Before treatment of the joints themselves, the panels must be filled between accidentally non-joined panels and various fillings. The application is done manually by "buttering" the thinned panels with a 10 or 15 cm coating knife and placing the strip. Then carry out a finishing pass, let dry and finish to mask the strip. Also mask the screw heads.

COMPOSITION AND APPEARANCE Powder coating based on plaster, calcium carbonate, resin, and various additives. The paste obtained is white in color. ADMITTED SUPPORTS All types of plasterboard with or without insulation with tapered edges and cardboard faces. COATINGS Plaster-based smoothing plaster. TECHNICAL SPECIFICATIONS - Setting time: 1/2 hour - Adhesion of the tape: > 1000 g - Cracking: no cracks up to 5 mm thick - Density: 0.9 - Reaction to fire: A1 STORAGE 9 months in original unopened packaging protected from humidity. SURFACE PREPARATION The plasterboards will be fixed in accordance with DTU 25.42. APPLICATION Before treatment of the joints themselves, the panels must be filled between accidentally non-joined panels and various fillings The application is done manually by "buttering" the thinned panels with a 10 or 15 cm coating knife and placing the strip. (Grinded face against the plaster).

Polished barrel with hardened cutting edge. Hole tapers inside for easy punching clearings. Available in 2 sizes. These punches should be used on an Micron Cutting Board.. The use of an Micron wooden mallet or rawhide hammer is recommended. Steel hammers are not recommended.

Features Flat spray pattern with a mountain-shaped spray distribution having gradually tapered edges. Tapered edges overlap to provide uniformity of spray distribution in multiple-nozzle arrangements. Applications Cleaning: Automotive, containers, films, felts, filters, screens, bottles, crushed stones, earth and sand, metal parts, machines, steel plates and pieces Spraying: Etchants, oils, lubricants, glues, solutions, insecticides, herbicides Cooling: Gas, smokes, heat exchangers, tanks, steels, roofs Water screen: Fire protection, heat protection, dust suppression, deodorization

Features Flat spray pattern with a mountain-shaped spray distribution having gradually tapered edges. Easy installation just by drilling a hole (φ14.3 mm) on a pipe and inserting a nozzle. Easy assemble and maintenance by quick detachable nozzles. Adaptors, color-coded by size, are available in 1″, 1 “, 1 “, 2”, 25A, and 30A. Spray tips are also color-coded by spray capacity for easy identification. Adjust spray direction within 50 degrees as desired. Applications Pre-treatment for painting: Car, home electric appliances Cleaning: water rinsing after acid treatment of steel plates, water rinsing process in food factory

Features Flat spray pattern with a mountain-shaped spray distribution having gradually tapered edges. Quick-detachable design helps to greatly reduce maintenance time. Easy mounting/dismounting with a knurled tab. No falling off of tip or packing when removing the nozzle part. [INVV series (plastic)] Made of high chemical and heat resistant PP (polypropylene). Nozzle tips are color-coded by spray capacity for easy identification. Applications [INVV series (plastic)] Cleaning Etching Stripping For the applications where precise spray alignment and/or periodic maintenance is required

Features Flat spray pneumatic nozzle producing fine atomization with a mean droplet diameter of 100 μm or less.** Ultra-compact size. About 42 mm in total length including control adaptor. Features large turn-down ratio under liquid pressures of 0.1–0.3 MPa (ca. 1 bar – 3 bar). Produces two different spray distributions: uniform spray distribution throughout spray pattern area (when spraying at a low air-water ratio), or a mountain-shaped distribution having gradually tapered edges (at a high air-water ratio). Spray angle of 110 °, 80 °, or 45 °.* Capable of spraying smallest flow rate among all of our pneumatic spray nozzles. Spray ON/OFF can be regulated by switching the pilot air ON/OFF (adaptor type SP) or by turning compressed air ON/OFF (adaptor type SN). *Spray angle measured at compressed air pressure of 0.3 MPa (ca. 3 bar) and liquid pressure of 0.1 MPa (ca. 1 bar). **Mean droplet diameter measured by Laser Doppler Method.

Features Flat spray pneumatic nozzle producing fine atomization with a mean droplet diameter of 100 μm or less (*3). Features large turn-down ratio under liquid pressures of 0.1–0.3 MPa (ca. 1 bar – 3 bar). Produces two different spray distributions: uniform spray distribution throughout spray pattern area (when spraying at a low air-water ratio), or a mountain-shaped distribution having gradually tapered edges (at a high air-water ratio). Spray angle of 110 °, 80 °, or 45 °. *1) Spray angle measured at compressed air pressure of 0.3 MPa (ca. 3 bar) and liquid pressure of 0.1 MPa (ca. 1 bar). *2) Free passage diameter of nozzle orifice. *3) Measured by Laser Doppler Method. Applications Spraying, Cooling, Moisture control, Cleaning, Dust suppression, etc.

Features Flat spray pneumatic nozzle producing fine atomization with a mean droplet diameter of 100 μm or less (*3). Features large turn-down ratio under liquid pressures of 0.1–0.3 MPa (ca. 1 bar – 3 bar). Produces two different spray distributions: uniform spray distribution throughout spray pattern area (when spraying at a low air-water ratio), or a mountain-shaped distribution having gradually tapered edges (at a high air-water ratio). Spray angle of 110 °, 80 °, or 45 °. *1) Spray angle measured at compressed air pressure of 0.3 MPa (ca. 3 bar) and liquid pressure of 0.1 MPa (1 bar). *2) Free passage diameter of nozzle orifice. *3) Measured by Laser Doppler Method. Applications Spraying, Cooling, Moisture control, Cleaning, Dust suppression, etc.