Measurement data - Import export

The remote data transmission unit ADT1-Box is encased in a robust, water-tight plastic housing. The LoRa module, which can be configured on a country-specific basis, establishes a connection with the Internet and makes it possible to collect measurement data in a low-cost and energy-saving manner. These autonomous devices can be linked with digital level sensors and pressure transmitters in the KELLER D and X product lines. With three conventional, high-quality AA batteries, the system can operate autonomously for up to 5 years. The LoRaWAN provider can be selected freely or an in-house or open source infrastructure and associated services can be used. The easiest and most convenient way to access the collected data at the end of the transmission chain is via KOLIBRI Cloud from KELLER.

The remote data transmission unit ADT1-Tube is encased in a robust, stainless steel housing, which is ideally suited to installation in 2" monitoring pipes. The LoRa module, which can be configured on a country-specific basis, establishes a connection with the Internet and makes it possible to collect measurement data in a low-cost and energy-saving manner. These autonomous devices can be linked with digital level sensors and pressure transmitters in the KELLER D and X product lines. With three conventional, high-quality AA batteries, the system can operate autonomously for up to 5 years. The LoRaWAN provider can be selected freely or an in-house or open source infrastructure and associated services can be used. The easiest and most convenient way to access the collected data at the end of the transmission chain is via KOLIBRI Cloud from KELLER.

The LEO5 digital manometers combine a range of functions from other KELLER manometers in a water-tight stainless steel housing. They can detect pressure peaks with a measurement interval of 5 kHz and record all measurements. Current measured values and saved data can be read out via the USB connection. The pressure values can be shown on the extra-large display in a wide range of units of pressure, which are either pre-programmed or configured by the user.

The DCX-22AA-CTD data loggers measure conductivity and temperature as well as pressure, along with the depth of bodies of water. They compensate for the air pressure using an additional, water-tight absolute pressure sensor with a stainless steel separating diaphragm. Unlike gauge pressure systems with a capillary tube, this system is completely resistant to moisture and can therefore be immersed. Thanks to their long-life battery, they can keep recording measurement results for years (up to 10 years at a rate of one measurement per hour). The logger can be configured using the supplied software (measurement interval, incident management, delayed measurement start etc.) and data that has been read can be displayed in a graph or chart, corrected using air pressure values, converted into fill levels or other units, and exported.

The DCX-22-CTD data loggers measure conductivity and temperature as well as pressure, along with the depth of bodies of water. The integrated Pt1000 achieves an accuracy of ±0,1 °C, and the conductivity can be measured at ± 2,5% of the selected range (0,2 / 2 / 20 / 200 mS/cm). Thanks to their long-life battery, they can keep recording measurement results for years (up to 10 years at a rate of one measurement per hour). The logger can be configured using the supplied software (measurement interval, incident management, delayed measurement start etc.) and data that has been read can be displayed in a graph or chart, corrected using air pressure values, converted into fill levels or other units, and exported.

The DCX-25PVDF data loggers have been specially designed for use in aggressive liquids such as brackish water and sewage. The housing is made of polyvinylidene fluoride and the installed pressure transducer is available in Hastelloy C-276 or titanium 6AL-4V. Thanks to their long-life battery, they can keep measuring the water level, water pressure and temperature for years (up to 10 years at a rate of one measurement per hour). The logger can be configured using the supplied software (measurement interval, incident management, delayed measurement start etc.) and data that has been read can be displayed in a graph or chart, corrected using air pressure values, converted into fill levels or other units, and exported.

The DCX-22 data loggers achieve greater measurement accuracy than loggers with a smaller diameter. Thanks to their long-life battery, they can keep measuring the water level, water pressure and temperature for years (up to 10 years at a rate of one measurement per hour). The data logger can be configured using the supplied software (measurement interval, incident management, delayed measurement start etc.) and data that has been read can be displayed in a graph or chart, corrected using air pressure values, converted into fill levels or other units, and exported.

The DCX-16 data loggers have a diameter of just 16 mm and can be used in tight spaces. Thanks to their long-life battery, they can keep measuring the water level, water pressure and temperature for years (up to 10 years at a rate of one measurement per hour). The logger can be configured using the supplied software (measurement interval, incident management, delayed measurement start etc.) and data that has been read can be displayed in a graph or chart, corrected using air pressure values, converted into fill levels or other units, and exported.

Windows software for displaying measurement data from the remote data transmission units GSM-2 and ARC-1 and for saving this data in a database.

Windows software for reading off and configuring data loggers. The measurement data can be displayed in graph form or exported. Air pressure compensation can also be carried out on the data, or it can be converted into water level values. The online function shows the current value of the device.

Windows software for communicating with connected KELLER devices. KOLIBRI Desktop offers all the options for device configuration and displays current measured values and logger recordings in graph form. Thanks to the search and filter options, saved measurement data can be organised with ease and exported as an image, as an Excel or Word report, or in additional formats. All products in the KOLIBRI suite are intercompatible and can exchange data with one another. The functions are continually being further expanded and optimised.

Web app for collecting and displaying measured values that are recorded by KELLER IoT devices and transmitted via mobile radio or LoRaWAN. KOLIBRI Cloud offers a wide variety of options for device configuration and displays current measured values and logger recordings in graph form. Thanks to the search and filter options, saved measurement data can be organised with ease and can also be exported as an image, as an Excel or Word report, or in additional formats. You can also use your existing software solutions to access data in KOLIBRI Cloud via JSON API. All products in the KOLIBRI suite are intercompatible and can exchange data with one another. The functions are continually being further expanded and optimised.