Studs for welding - Import export

Stud Welding is the process of sticking to the surface as a result of applying spring force by applying a quick process to the area to be welded, ensuring the melting of the surface by pressing. There is no need for any preliminary preparation. In other words, no operation such as drilling is performed. The only thing that is wanted is that the surface is clean. It creates a strong connection. There will be no traces of welding. The production cost becomes lower and it is also advantageous in terms of time. It will be enough to conduct a study for one reason or another. For two hundred, there is no need to perform an operation. It can be used for a variety of metals. Materials such as iron, steel, aluminum and stainless are the most preferred stud welding materials.

Semiautomatic capacitor-discharge stud welding with ignition tip M3 – M8 Diameter 3 – 8 mm Steel, Stainless steel Aluminium alloys Welding sources LBS

Your expert in welding technics like MIG, MAG, WIG, resistance spot & stud welding, e-welding, welding robots For the returning serial welding tasks, 2 gantry welding robot system are available. With a machining length of up to 8 meters (26,2 ft), we can lealize complex customer requests thanks to 10 treatment axis performance. We are authorized to weld structural steelwork in accordance to EN1090

Toothed belt brushes from Kullen complement the belt brush range and offer one advantage in the feeding technique which the others do not: they can be set to a measurable cycle time. We only use standard toothed belts made of polyurethane with especially welded studs for fixing the fill material. The toothed belts are resistant against humidity, oils, greases and most chemicals. They can be used at temperatures between -15°C up to 80°C. Our experience shows that the required variations of toothed belt brushes are specific according to the customer's application and thus are normally produced ready to be installed as an endless unit. This brush type is available in common widths (KB) of standard toothed belts divided in T5, T10 and T20. The belt length depends on your requirements. You should always inform us about the inside belt length. The maximum belt speed is 6 m/s. Mainly natural hairs and bristles, plant fibres and synthetic bristles (PP, PA, etc.) are used, so all kinds of...

As a combination of blind rivet nut and screw, blind rivet nut studs offer an alternative or replacement for welding studs. The following applications are particularly suitable for the use of GESIPA® blind rivet nut studs: • Accessibility from one side only • Thin carrier materials (sheet metal, plastics, etc.) • Necessary pre-centering • On heat sensitive application materials (e.g. welding not possible) • Surface coatings must not be damaged • Production of electrically conductive joints • Fast replacement of welding studs (repairs) GESIPA® blind rivet nut studs can be set without any problem with the GESIPA® blind rivet nut setting tools FireBird®, GBM 95 and FireFox® using corresponding adapters (see tool description) for blind rivet nut studs

The self-clinching stud is the modern and rational alternative to the weld-on stud. The stud is easily applied to metal sheets of various thicknesses creating a secure, unequaled-looking attachment with very high strength values. There is almost no damage to the surface of the sheet metal and its treatment This self-clinching stud is part of our line of self-clinching inserts. All Clinch inserts are installed using a simple punch During installation process, the fastener is placed in an appropriately sized hole and then compressed by means of a punch, applyinng only sufficient pressure to squeeze the stud head and its under head tooth features into the parent sheet. The sheet metal experiences plastic deformation and locks the fastener firmly to itself. After installation the spigot joint should be flush with the sheet, so the result is aesthetically perfect. And the tooth locking feature provides high tensile as well as torsional strength

: Clamp made out of a pre-rolled plate of stainless steel AISI 304. Clamp is manufactured with a hinge point in order to simplify installation. Design with welded AISI 304 studs and fingers. Clamp is completely pickled and passivated after welding. Studs are Teflon coated to prevent cold welding (galling). Stainless steel nuts made out of A4 quality. Gasket of EPDM rubber with waffle structure and rounded tops. Spanner plate is completely vulcanized with rubber gasket. Diameter reach of double band repair clamp is max. 24 mm (depends on diameter pipe). Clamp available in different diameters: DN 80 up to DN 600. Clamp available in different lenghts: 200, 250, 300, 400, 500 and 600 mm (other lengths on request). Indication pressure class for (waste)water: 16 bar for DN 80 up to DN 150, 10 bar for DN 175 up to DN 450 and 6 bar from DN 500. Studs protected with plastic protection caps.

Clamp made out of a pre-rolled plate of stainless steel AISI 304. Design with welded AISI 304 studs (50 mm center to center) and fingers. Clamp is completely pickled and passivated after welding. Studs are Teflon coated to prevent cold welding (galling). Stainless steel nuts made out of A4 quality. Gasket of NBR rubber with waffle structure and rounded tops. Spanner plate is completely vulcanized into rubber gasket. Diameter reach of double band repair clamp is max. 36 mm (depends on diameter pipe). Clamps available in different diameters: DN 250 up to DN 800. Clamps available in different lenghts: 300, 400, 500, 600 and 800 mm (other lengths on request). Indication pressure class for (waste)water: 10 bar for DN 250 up to DN 450, 6 bar for DN 500 up to DN 600, 4 bar for DN 650 and 3 bar from DN 700. Indication pressure class for gas:2 bar for DN 250 up to DN 450, 1, 5 bar for DN 500 up to DN 600, 1 bar for DN 650 and 0,8 bar from DN 700. Studs protected with plastic protection caps.

Clamp made out of a pre-rolled plate of stainless steel AISI 316. Design with welded AISI 316 studs and fingers. Clamp is completely pickled and passivated after welding. Studs are Teflon coated to prevent cold welding (galling). Stainless steel nuts made out of A4 quality. Gasket of NBR rubber with waffle structure and rounded tops. Spanner plate is completely vulcanized into rubber gasket. Diameter reach of double band repair clamp is max. 36 mm (depends on diameter pipe). Clamps available in different diameters: DN 250 up to DN 800. Clamps available in different lenghts: 300, 400, 500, 600 and 800 mm (other lengths on request). Indication pressure class for (waste)water: 10 bar for DN 250 up to DN 450, 6 bar for DN 500 up to DN 600, 4 bar for DN 650 and 3 bar from DN 700. Indication pressure class for gas:2 bar for DN 250 up to DN 450, 1, 5 bar for DN 500 up to DN 600, 1 bar for DN 650 and 0,8 bar from DN 700. Studs protected with plastic protection caps.

Clamp made out of a pre-rolled plate of stainless steel AISI 304. Design with welded AISI 304 studs and fingers. Clamp is completely pickled and passivated after welding. Studs are Teflon coated to prevent cold welding (galling) Stainless steel nuts made out of A4 quality. Gasket of EPDM rubber with waffles structure and rounded tops. Spanner plate is completely vulcanized into rubber gasket. Diameter reach of double band repair clamp is max. 36 mm (depends on diameter pipe). Clamps available in different diameters: DN 250 up to DN 800. Clamps available in different lenghts: 300, 400, 500, 600 and 800 mm (other lengths on request). Indication pressure class for water: 10 bar for DN 250 up to DN 450, 6 bar for DN 500 up to DN 600, 4 bar for DN 650 and 3 bar from DN 700. Studs protected with plastic protection caps.

China Sheet Metal Stamping Parts Factory custom produce Aluminum,Carbon & Stainless Steel,Brass & Copper Stamping Parts as per customers’ drawing or samples. Have custom many kinds of metal stamping parts,such as sheet metal stamping clamps, metal seals, sheet metal brackets, sheet metal holder,console cover,sheet metal frames,spring clip, steel plates,shelf,Square/ Rectangular washers, metal stamped PCBA front Panel, pressed-in hole parts by PEM studs,nuts & fasteners, screw and pin welded stamping housings. Materials can be stainless steel,carbon steel,aluminum alloy,brass & copper,etc Finshing Operations: Forming, Bending,Deburring, Tapping,Riveting,Welding Surface Finish: zinc plating,chromed,nickel plating,oiled,painting,powder coating,hot-galvanizing,heat treatment & blackening,etc Mould Accuracy is 0.01mm-0.05mm We are professional metal stamping supplier from China, we custom sheet metal stamping parts for foreign customers more than 15 years.

Clamp made out of a pre-rolled plate of stainless steel AISI 304. Design with welded AISI 304 studs and fingers. Clamp is completely pickled and passivated after welding. Studs are Teflon coated to prevent cold welding (galling). Stainless steel nuts made out of A4 quality. Gasket of NBR rubber with waffle structure and rounded tops. Spanner plate is completely vulcanized into rubber gasket. Diameter reach of double band repair clamp is max. 36 mm (depends on diameter pipe). Clamps available in different diameters: DN 250 up to DN 800. Clamps available in different lenghts: 300, 400, 500, 600 and 800 mm (other lengths on request). Indication pressure class for (waste)water: 10 bar for DN 250 up to DN 450, 6 bar for DN 500 up to DN 600, 4 bar for DN 650 and 3 bar from DN 700. Indication pressure class for gas:2 bar for DN 250 up to DN 450, 1, 5 bar for DN 500 up to DN 600, 1 bar for DN 650 and 0,8 bar from DN 700. Studs protected with plastic protection caps.

Clamp made out of a pre-rolled plate of stainless steel AISI 304. Design with welded AISI 304 studs (50 mm center to center) and fingers. Clamp is completely pickled and passivated after welding. Studs are Teflon coated to prevent cold welding (galling). Stainless steel nuts made out of A4 quality. Gasket of NBR rubber with waffle structure and rounded tops. Spanner plate is completely vulcanized into rubber gasket. Diameter reach of double band repair clamp is max. 36 mm (depends on diameter pipe). Clamps available in different diameters: DN 250 up to DN 800. Clamps available in different lenghts: 300, 400, 500, 600 and 800 mm (other lengths on request). Indication pressure class for (waste)water: 10 bar for DN 250 up to DN 450, 6 bar for DN 500 up to DN 600, 4 bar for DN 650 and 3 bar from DN 700. Indication pressure class for gas:2 bar for DN 250 up to DN 450, 1, 5 bar for DN 500 up to DN 600, 1 bar for DN 650 and 0,8 bar from DN 700. Studs protected with plastic protection caps.

: Clamp made out of a pre-rolled plate of stainless steel AISI 316. Clamp is manufactured with a hinge point in order to simplify installation. Design with welded AISI 316 studs and fingers. Clamp is completely pickled and passivated after welding. Studs are Teflon coated to prevent cold welding (galling). Stainless steel nuts made out of A4 quality. Gasket of EPDM rubber with waffle structure and rounded tops. Spanner plate is completely vulcanized with rubber gasket. Diameter reach of double band repair clamp is max. 24 mm (depends on diameter pipe). Clamp available in different diameters: DN 80 up to DN 600. Clamp available in different lenghts: 200, 250, 300, 400, 500 and 600 mm (other lengths on request). Indication pressure class for water: 16 bar for DN 80 up to DN 150, 10 bar for DN 175 up to DN 450 and 6 bar from DN 500. Studs protected with plastic protection caps.

: Clamp made out of a pre-rolled plate of stainless steel AISI 316. Clamp is manufactured with a hinge point in order to simplify installation. Design with welded AISI 316 studs and fingers. Clamp is completely pickled and passivated after welding. Studs are Teflon coated to prevent cold welding (galling). Stainless steel nuts made out of A4 quality. Gasket of NBR rubber with waffle structure and rounded tops. Spanner plate is completely vulcanized with rubber gasket. Diameter reach of double band repair clamp is max. 24 mm (depends on diameter pipe). Clamp available in different diameters: DN 80 up to DN 600. Clamp available in different lenghts: 200, 250, 300, 400, 500 and 600 mm (other lengths on request). Indication pressure class for (waste)water: 16 bar for DN 80 up to DN 150, 10 bar for DN 175 up to DN 450 and 6 bar from DN 500. Indication pressure class for gas: 2 bar for DN 250 up to DN 450, 1,5 bar for DN 500 up to DN 600, 1 bar for DN 650 and 0.8 bar from DN 700. Studs...

: Clamp made out of a pre-rolled plate of stainless steel AISI 304. Clamp is manufactured with a hinge point in order to simplify installation. Design with welded AISI 304 studs and fingers. Clamp is completely pickled and passivated after welding. Studs are Teflon coated to prevent cold welding (galling). Stainless steel nuts made out of A4 quality. Gasket of EPDM rubber with waffle structure and rounded tops. Spanner plate is completely vulcanized with rubber gasket. Diameter reach of double band repair clamp is max. 24 mm (depends on diameter pipe). Clamp available in different diameters: DN 80 up to DN 600. Clamp available in different lenghts: 200, 250, 300, 400, 500 and 600 mm (other lengths on request). Indication pressure class for (waste)water: 16 bar for DN 80 up to DN 150, 10 bar for DN 175 up to DN 450 and 6 bar from DN 500. Studs protected with plastic protection caps.

Clamp made out of a pre-rolled plate of stainless steel AISI 304. Design with welded AISI 304 studs and fingers. Clamp equipped with hand grip in order to simplify installation. Clamp is completely pickled and passivated after welding. Studs are Teflon coated to prevent cold welding (galling). Stainless steel nuts made out of A4 quality. Gasket of EPDM rubber with waffle structure and rounded tops. Spanner plate is completely vulcanized with rubber gasket. Diameter reach of single band repair clamp is max. 12 mm (depends on diameter pipe). Clamps available in different diameters: DN 40 up to DN 350. Clamps available in different lenghts: 100, 150, 200, 250, 300, 400, 500 and 600 mm (other lengths on request). Indication pressure class for (waste)water: 16 bar for DN 40 up to DN 150, 10 bar for DN 175 up to DN 300 and 6 bar for DN 350. Studs protected with plastic protection caps.

Clamp made out of a pre-rolled plate of stainless steel AISI 316. Design with welded AISI 316 studs and fingers. Clamp is completely pickled and passivated after welding. Studs are Teflon coated to prevent cold welding (galling). Stainless steel nuts made out of A4 quality. Gasket of EPDM rubber with waffle structure and rounded tops. Spanner plate is completely vulcanized with rubber gasket. Diameter reach of single band repair clamp is max. 12 mm (depends on diameter pipe). Clamps available in different diameters: DN 40 up to DN 350. Clamps available in different lenghts: 100, 150, 200, 250, 300, 400, 500 and 600 mm (other Indication pressure class for (waste)water: 16 bar for DN 40 up to DN 150, 10 bar for DN 175 up to DN 300 and 6 bar for DN 350. Studs protected with plastic protection caps.

Clamp made out of a pre-rolled plate of stainless steel AISI 316. Clamp is completely pickled and passivated after welding. Studs are Teflon coated to prevent cold welding (galling). Stainless steel nuts made out of A4 quality. Gasket of NBR rubber with waffle structure and rounded tops. Spanner plate is completely vulcanized with rubber gasket. Diameter reach of single band repair clamp is max. 12 mm (depends on diameter pipe). Clamps available in different diameters: DN 40 up to DN 350. Clamps available in different lenghts: 100, 150, 200, 250, 300, 400, 500 and 600 mm (other lengths on request). Indication pressure class for (waste)water: 16 bar for DN 40 up to DN 150, 10 bar for DN 175 up to DN 300 and 6 bar for DN 350. Indication pressure class for gas: 4 bar for DN 40 up to DN 150, 3 bar for DN 175 up to DN 300 and 2 bar for DN 350. Studs protected with plastic protection caps.

Feature Clamp made out of a pre-rolled plate of stainless steel AISI 304. Design with welded AISI 304 studs and fingers (50 mm center to center). Clamp is completely pickled and passivated after welding. Studs are Teflon coated to prevent cold welding (galling). Stainless steel nuts made out of A4 quality. Gasket of EPDM rubber with waffle structure and rounded tops. Spanner plate is completely vulcanized with rubber gasket. Diameter reach of single band repair clamp is max. 12 mm (depends on diameter pipe). Clamps available in different diameters: DN 40 up to DN 350. Clamps available in different lenghts: 100, 150, 200, 250, 300, 400, 500 and 600 mm (other lengths on request). Indication pressure class for (waste)water: 24 bar for DN 40 up to DN 150, 16 bar for DN 175 up to DN 300 and 10 bar for DN 350. Studs protected with plastic protection caps.

Clamp made out of a pre-rolled plate of stainless steel AISI 304. Design with welded AISI 304 studs and fingers. Clamp is completely pickled and passivated after welding. Studs are Teflon coated to prevent cold welding (galling). Stainless steel nuts made out of A4 quality. Gasket of EPDM rubber with waffle structure and rounded tops. Spanner plate is completely vulcanized with rubber gasket. Diameter reach of single band repair clamp is max. 12 mm (depends on diameter pipe). Clamps available in different diameters: DN 40 up to DN 350. Clamps available in different lenghts: 100, 150, 200, 250, 300, 400, 500 and 600 mm (other lengths on request). Indication pressure class for (waste)water: 16 bar for DN 40 up to DN 150, 10 bar for DN 175 up to DN 300 and 6 bar for DN 350. Studs protected with plastic protection caps.

Clamp made out of a pre-rolled plate of stainless steel AISI 304. Design with welded AISI 304 studs and fingers (50 mm center to center). Clamp is completely pickled and passivated after welding. Studs are Teflon coated to prevent cold welding (galling). Stainless steel nuts made out of A4 quality. Gasket of NBR rubber with waffle structure and rounded tops. Spanner plate is completely vulcanized with rubber gasket. Diameter reach of single band repair clamp is max. 12 mm (depends on diameter pipe). Clamps available in different diameters: DN 40 up to DN 350. Clamps available in different lenghts: 100, 150, 200, 250, 300, 400, 500 and 600 mm (other lengths on request). Indication pressure class for (waste)water: 24 bar for DN 40 up to DN 150, 16 bar for DN 175 up to DN 300 and 10 bar for DN 350. Indication pressure class for gas: 6 bar for DN 40 up to DN 150, 4 bar for DN 175 up to DN 300 and 3 bar for DN 350. Studs protected with plastic protection caps.

Clamp made out of a pre-rolled plate of stainless steel AISI 304. Design with welded AISI 304 studs and fingers. Clamp is completely pickled and passivated after welding. Studs are Teflon coated to prevent cold welding (galling). Stainless steel nuts made out of A4 quality. Gasket of NBR rubber with waffle structure and rounded tops. Spannerplate is completely vulcanized with rubber gasket. Diameter reach of single band repair clamp is max. 12 mm (depends on diameter pipe). Clamps available in different diameters: DN 40 up to DN 350. Clamps available in different lenghts: 100, 150, 200, 250, 300, 400, 500 and 600 mm (other lengths on request). Indication pressure class for (waste)water: 16 bar for DN 40 up to DN 150, 10 bar for DN 175 up to DN 300 and 6 bar for DN 350. Indication pressure class for gas: 4 bar for DN 40 up to DN 150, 3 bar for DN 175 up to DN 300 and 2 bar for DN 350. Studs protected with plastic protection caps.

China Sheet Metal Stamping Parts Factory custom produce Aluminum,Carbon & Stainless Steel,Brass & Copper Stamping Parts as per customers’ drawing or samples. Have custom many kinds of metal stamping parts,such as sheet metal stamping clamps, metal seals, sheet metal brackets, sheet metal holder,console cover,sheet metal frames,spring clip, steel plates,shelf,Square/ Rectangular washers, metal stamped PCBA front Panel, pressed-in hole parts by PEM studs,nuts & fasteners, screw and pin welded stamping housings. Materials can be stainless steel,carbon steel,aluminum alloy,brass & copper,etc Finshing Operations: Forming, Bending,Deburring, Tapping,Riveting,Welding Surface Finish: zinc plating,chromed,nickel plating,oiled,painting,powder coating,hot-galvanizing,heat treatment & blackening,etc Mould Accuracy is 0.01mm-0.05mm We are professional metal stamping supplier from China, we custom sheet metal stamping parts for foreign customers more than 15 years.

Ming Xiao Manufacturing Custom Welded parts From all kind of carbon steels,stainless steels,aluminum,copper,Brass. We can produce weled parts from GTAW (Gas Tungsten Arc Weld),SMAW (Shielded Metal Arc Welding), MIG Welding (melt inert-gas welding),TIG Welding(Tungsten Inert Gas Welding) and laser welding for high quality required parts. Our Factory have may spot welding machines,butt welding machines, Argon shielded arc welding machine, Most welded metal parts use spot welding, the spot welding is the fastest way for small welding points, so say its spot welding. its can weld a net metal parts with many spots in consecutive. The welding services are widely use for welded brackets, welded wire frames, welded covers, welded studs on plates. Welcome contact us to discuss your welded metal parts.

In many areas, stud welding is considered to be the most economic fastening method for components and is sometimes even the only technically feasible solution. Because the stud is joined with the substructure over the entire surface of the stud without any hollow areas, a high strength can be achieved. STAUFF is now using this proven principle for the installation of pipe, tube, hose and cable clamps in the Standard and Twin Series (according to DIN 3015, parts 1 and 3) with M6 mounting thread, where female threaded weld studs replace the regular weld plates; distance plates made from plastic provide the necessary spacing between the clamp bodies and the substructure. If required, the system can also be adopted for alternative fastening methods, e.g. for clamping belts, cable ties or corrugated cable protection hoses. In addition to the individual components – weld studs, distance plates, clamp bodies and metal hardware required – the company also provides the correspondingly...

Weldable stud range 3–10 mm Ideal for KÖCO Stud Welding Equipment KST Ergonomic body

Weldable stud range 3–10 mm Ideal for KÖCO Stud Welding Equipment KST Ergonomic body

The model K 26 is a robust stud welding gun, especially for studs ø 22 – 25 mm Ideal for welding shear connectors SD 25 mm Ideal for through-deck-welding td Most suitable for long shear studs Adjustable hydraulic plunge damper Standard support with 3 legs Body: fibre-glass reinforced polyamide Lifting ring system with length compensation up to 8mm Control cable plug (4 wire) Optimal Integrated shielding gas device