Results for
Spain
SURFACE FINISH. APPROVED FINISHES EN 10202 Bright, Fine stone, Stone, Silver, Matt COATING. PRECISE VALUES FOR TIN COATINGS EN 10202 HICKNESS TOLERANCES Thickness tolerances and edge reduction according to EN 10202 The thickness of the material must meet the following requirements: a) Deviation from the agreed thickness, measured on the centre line of the strip, must not exceed ± 5%. b) Deviation from the agreed thickness, measured at any point at a distance of no less than 6 mm from the sheared edge, must be between +5% and -8%. WIDTH TOLERANCES Other, closer dimensional tolerances are possible under a commercial agreement. EDGE CAMBER TOLERANCES Tolerances for edge bending under commercial agreement.
Request for a quoteSpain
SURFACE FINISH. APPROVED FINISHES EN 10202 Bright, Fine stone, Stone, Silver, Matt COATING. PRECISE VALUES FOR TIN COATINGS EN 10202 HICKNESS TOLERANCES Thickness tolerances and edge reduction according to EN 10202 The thickness of the material must meet the following requirements: a) Deviation from the agreed thickness, measured on the centre line of the strip, must not exceed ± 5%. b) Deviation from the agreed thickness, measured at any point at a distance of no less than 6 mm from the sheared edge, must be between +5% and -8%. WIDTH TOLERANCES Other, closer dimensional tolerances are possible under a commercial agreement. EDGE CAMBER TOLERANCES Tolerances for edge bending under commercial agreement.
Request for a quoteSpain
THICKNESS TOLERANCES : Thickness tolerances according to EN 10051 for nominal widths. WIDTH TOLERANCES: Width tolerances according to EN 10051 for nominal widths Other, closer dimensional tolerances on request. EDGE CAMBER TOLERANCES: Sag tolerances according to EN 10051 for pickled hot-rolled strips will be agreed when placing the order. RIPPLE - LONGITUDINAL FLATNESS: The flatness tolerance of the strips in cut lengths in the direction of rolling must be a maximum of 10 mm on 1000 mm. Any other flatness requirement must be agreed when placing the order.
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
Spain
POSSIBILITY OF SUPPLY: Whitout coating: Annealed, N/A and Hard Drawn ( Grey) Whith coating: Annealed Galvanised and Hard Galvanised ( Grey) TYPES OF COATING: Galvanised - Reinforced galvanised - ZA - Reinforced ZA
Request for a quoteSpain
FINISHES: SURFACE QUALITY PROPERTIES OF THE COATINGS GALVANISED STEEL according to EN 10142 Check our website for coating mass, coating finish, surface quality and protection surface treatment. If the customer does not require the surfaces to be oiled and/or chemically passivated, this must be clearly indicated when requesting the quote and placing the order. THICKNESS TOLERANCES Thickness tolerances according to EN 10143 for nominal widths. WIDTH TOLERANCES Tolerances on wide strips obtained by longitudinal cutting of a width of less than 600 mm.According to Standard EN 10143 of: w < 125; 125 w < 250; 250 w < 400; 400 w < 600. Other, closer dimensional tolerances under a commercial agreement. SAG TOLERANCES Edge curve tolerances under commercial agreement
Request for a quoteSpain
FINISHES: SURFACE QUALITY PROPERTIES OF THE COATINGS GALVANISED STEEL according to EN 10142 Check our website for coating mass, coating finish, surface quality and protection surface treatment. If the customer does not require the surfaces to be oiled and/or chemically passivated, this must be clearly indicated when requesting the quote and placing the order. THICKNESS TOLERANCES Thickness tolerances according to EN 10143 for nominal widths. WIDTH TOLERANCES Tolerances on wide strips obtained by longitudinal cutting of a width of less than 600 mm.According to Standard EN 10143 of: w < 125; 125 w < 250; 250 w < 400; 400 w < 600. Other, closer dimensional tolerances under a commercial agreement. SAG TOLERANCES Edge curve tolerances under commercial agreement
Request for a quoteResults for
Low-carbon - Import exportNumber of results
10 ProductsCountries
Company type