Signal generators - Import export

The BH25 is a high resolution exposed linear encoder with interferometric measurement signal generation. The BH25 scale has a graduation period of 1µm. The interferometric laser scale principle generates a sinusoidal measurement signal with a signal period of 250nm in the read head. The BH25 is characterized by its small size and high signal quality. It is suitable for resolutions of up to 3.8pm. Due to the reflective scanning and the small design it is perfectly suited for high accuracy X/Y stages with linear motor drive as well as for measurement applications

The BS78 is a high accuracy exposed linera encoder with an interferometric signal generation in transmitted light design. The scale has a graduation period of 0.55µm. The LASERSCALE operating principle generates a sinusoidal measuring signal with a signal period of 138nm. This has an extremely high signal quality with a very low noise component. This allows resolutions of up to 2.1 pm to be generated. Due to the extremely low interpolation error, the BS78 is perfectly suited for ultra precision machining, measurement and calibration applications.

The BL57 is a high-resolution, exposed linear encoder with interferometric operating principle in transmitted light design. The BL57 has a graduation period of 1.6µm and generates a sinusoidal signal period of 400nm due to the laserscale operating principle. This allows resolutions of up to 6.1pm. to be achieved. Due to the high response speed of up to 3m/s, it is perfectly suited for high-precision and fast X/Y stages.

High-precision angle measuring system with +/-0.1s accuracy for measuring and calibration applications. The signal sampling is done by an interferometric operating principle (laserscale) The graduation period is 1µm, the generated signal period of the output signal is 250nm. Scale errors are self-compensated by using six reading heads in a special arrangement. The measured values can be output in csv format via the USB interface. The software for measured value acquisition and storage is included in the scope of delivery.

The BL50H is a high resolution exposed linear encoder in reflective design. The BL50H has a grating period of 1.6µm and generates a signal period of 400nm with the Laserscale operating principle. The extremely small dimensions, made possible by the reflective design and large mounting tolerances, allow easy integration into X/Y stages and a wide variety of measurement applications. It provides a very high signal quality with low noise level and is suitable for resolutions up to 6pm at travel speeds up to 3m/s.

The PD200 is a professional impulse current measuring system to detect leak (holes) in non-conductive sealing systems and is suitable for leak detection on balconie, pond liners/swimming pools or flat roofs. In contrast to the previous model PD100, the PD200 has extremely compact dimensions - the size of the device could be reduced by more than 30%! These compact dimensions enable the transport of the PD200 e.g. through so-called safety ladders to the corresponding flat roof.The impulse current measuring system easily wins the weight comparison with its previous model. Although the single components partially are pretty heavy (e.g. the transformer), the total weight could be reduced by about 20% (from 11.2 kg to 8.6 kg). On top of the housing there are clearly visible signal lamps - one standard impulse signal (green) and one short-circuit signal (red), incl. integrated tone generator.

Microwave measurement device, Continuous InLine measurement of dry matter or consistency Description At the microwave measurement technology an electromagnetic wave with very low energy is generated. This signal is coupled via an antenna into the product (Cellulose, Cheese, Milk, Curd, etc.). Depending on the dielectric properties of the product the signal propagates in the product. After the signal has passed the product a second antenna receives the signal (Transmission). Amplitude and phase shift of the received signal are an expression for the consistency, water content or dry matter of the product. The microwave measurement is very stable and it has a quick response to product changes.

The ideal introduction to the world of vibration measurement. With four analog input channels, the Mosquito offers the ability to detect a triaxial vibration sensor and a speed signal. Alternatively, a modal hammer could also be operated for a measurement with subsequent modal analysis. •,4 analog input channels (from +/-10uV to +/- 100V) •,1 digital input channel (0-5V CMOS) •,1 analog output with signal generator (DC, 0-100kHz sine, sweep) •,Up to 100kHz bandwidth synchronously sampled across all channels •,16/24 bit resolution with 110+dB signal-to-noise ratio •,Compact dimensions (40 x 90 x 170 mm) •,Freely scalable! From one device with 4 analog channels to multiple devices with any number of channels •,1x Ethernet interfaces, connection for external 12V power supply, LVDS port for synchronization of multiple devices, USB port, IRIG input

In addition to purely switching sensors, your sensor specialist EGE also offers you inductive proximity switches with analogue output for measuring tasks. The analogue signal is proportional to the approximation of the metal part. This sensor is also available in a version up to 160° C. The proximity sensor is based on the proven inductive principle: When metallic objects come close, the resonant circuit of a coil is dampened through induction and an analogue signal generated from it. Analogue inductive are e.g. suitable for the double occupation control of metal plates, for the tensioning control of wire or for monitoring metallic brake pads.

Conductive level monitor for the detection of conductive media. With this sensor, the resistance between two electrodes is measured. If a medium shorts both electrodes, the resistance decreases and a switching signal is generated. Buildup is no problem for this sensor.

ULTRASense is a compact, airborne ultrasound sensor that connects directly to specific SDT instruments via a direct coupled LEMO7 input. It’s primary design and function is to detect sources of airborne ultrasound including positive and negative pressure leaks, electrical partial discharge, mechanical defects in belt drives, chain drives, and direct coupled shafts. ULTRASense detects signals generated by T-Sonic1 and T-Sonic9 ultrasound transmitters and is therefore applicable to tightness inspections.

Proper purging is absolutely essential to guarantee high-quality welding of high-alloyed, corrosion-resistant components. As part of this the Oxy EVO oxygen analyser can be connected to our orbital welding controllers for the purpose of inspecting and documenting the residual oxygen content and evaluated. — Extremely easy menu navigation — For inert gases and gases containing H2 (max. 10%) — Measuring cell made of zirconium oxide (maintenance-free) — 3.5" colour touch display — USB interface for exporting documentation — Digital and analogue interface and Bluetooth for communication with our orbital welding controllers and other PSPS — Activation and evaluation exclusively using the digital interface — User-definable threshold and alarm adjustment — Acoustic signal generator ... Package includes: — Oxygen analyser — Power cable — Hose set, 3 m, incl. filter and probe — Calibration certificate — Transport case

Barrier tape for generic signals, in two-tone white and red polyethylene. Packed in bulk.

we offer a collection of winter work clothes of our own production, request a catalog of our products by phone (whatsapp) +393292198195, mail tailor0612it@gmail.com website https://sumytekstil.prom.ua/

The high-voltage generator DG 206 is used to supply KERSTEN neXt® discharging components. The high-voltage generator DG 206 is supplied by an input voltage of DC 24V ± 20%. An LED displays the operational readiness as well as any feedback relating to a short-circuit error in one of the connected discharging components. The short-circuit error Feedback and a cable rupture detection also takes place via a 24V DC signal. The high-voltage generator offers 2 touch-safe high-voltage connections.

The CMME is a small profile footprint charging generator specially designed for IML applications. The unit has fully integrated high voltage parts and only needs a 24V DC supply. The housing is compact, robust and only weighs 480 grams which makes it perfect for end of arm mounting in IML pick and placehandling systems. It can easily withstand the high G-forces occurring during the IML process. The CMME has a unique (patented) cyle OK feature. A signal will become active when the label(s) have accumulated enough electrostatic charge indicating that the charging is finished. This signal can be used by the machine interface to decide to stop charging. A second stage in the cycle OK signal will indicate that the charge on the mandrell has dropped below asafe level to start moving the mandrell out of the mould.This innovative feature completely eliminates the guess work and experimental setup for each individualIML application, and when changing product or label.

Automatic synchronization to the line over a 1:6 speed range (requires a 0 V to 10 V signal proportional to the line speed); for lines providing no such control signal a dedicated frequency generator with tachometer wheel and incremental encoder is required. V - AUTOMATIC VISCOSITY CONTROL FOR PRINTING INKS An oscillating sensor causes thinner to be added when the viscosity deviates from a preset value. LD - INK LEVEL SENSOR AND INDICATOR SYSTEM Triggers a warning signal as the ink level drops below minimum. FW - INK FLOW SENSOR AND INDICATOR SYSTEM Triggers a warning signal as the ink flow deviates by an adjustable amount from the preset value. MARKING DRUMS Easily replaceable pairs of marking drums for use as spares for supplied marking drums or for changing the ring spacing or pattern. Standard ring patterns include single or double rings every 17 mm; double rings every 34 mm; one, two, three, or four rings every 60 mm

The DFC locking electronics consisting of the Phase Frequency Detector (PFD) and FALC 110 provides high-end phase frequency locking for comb applications. The PFD RF input is designed for use with the RF output signal of the DFC MD. The error signal generated by the PFD is fed to the input of the FALC 110 regulator. The main output of the FALC is passed through the PFD to allow for remote switching of the fast feedback loop which modulates the laser diode current. A copy of the error signal (mon. out) is used to close the slow feedback loop acting on the DL pro piezo (Fine In) with the all-digital PID of the DLC pro. Slow and fast feedback loop can be enabled and disabled with a push of a button in the DFC user interface (TOPAS DFC).

RAMOS CARS is the multifunctional multi-channel 3D scanning laser microscope-spectrometer. RAMOS CARS is intended for simultaneous and multifunctional analysis: high-speed imaging by CARS signal; confocal Raman imaging; confocal fluorescence imaging; confocal imaging in the reflected laser radiation; high-contrast imaging in the transmitted laser radiation; as well as visualization of a surface profile by means of the second harmonics generation signal. Microscope RAMOS CARS combines in one system: - CARS scanning microscope - Raman/luminescent scanning confocal microscope - Conventional scanning confocal laser microscope Applications: - Nanobiotechnology: real-time noninvasive analysis of biological samples (cells and components of living cells) with high spatial resolution. - Micro- and nanotechnology investigations of properties of non-biological microstructures: semiconductors, liquid crystals, polymers, pharmaceutical components, micro- and nanoparticles.

Recording of the angular position by means of Hall sensor and signal processing, including generation of the analogue output signal. Incrémental ou absolu: Absolu

The incremental encoder with the model designation FOI records the angular position by means of a magnetic sensor and signal processing and generates the corresponding pulse outputs. The robust steel housing with anti-corrosion coating and stainless steel flange (AIMgSi1) ensures versatile use of the incremental encoder for your individual application. The shaft of the FOI is made of stainless steel and the bearings are equipped with a shaft sealing ring.

Angle position measurement by means of Hall sensors and signal processing including generation of the analogue output signal. Robust brass housing – stainless steel shaft with sliding bearing – sensor circuit consisting of ASIC with Hall elements – electrical connection via connector.

Recording of the angular position by means of a Hall sensor and signal processing including generation of the output signal - in addition to the angular position, a speed signal can also be output in digits / time unit - electrical connection via screw clamp (5-pin, conductor cross-section max. 0.5 mm²) or PTFE pigtail connector, 300 mm long - a CAN controller at the output enables connection to the CANopen network. According to CANopen Application Layer and Communication Profile, CiA Draft Standard 301, Version 4.1 and according to Device Profile for Encoders CiA Draft Standard Proposal 406, Version 3.0 and CANopen Layer setting Services and Protocol (LSS), CiA DSP 305. In the multiturn version, the number of revolutions is recorded in a counter. The position value is saved on shutting off the supply voltage. In voltage-free condition, the position value is recorded on movement of the shaft in a range of ≤ ± 90°.

The TT 160 and TT 460 tool touch probes aretouch trigger probes for the measurement and inspection of tools. The TT 160 features signal transmission by cable, while the TT 460 communicates wirelessly over a radio or infrared beam with the SE 660 transmitter/receiver unit. The disk-shaped probe contact of the TT is defl ected during physical probing of a tool. At that moment the TT generates a trigger signal that is transmitted to the control, where it is processed further. The trigger signal is generated through a wear-free optical switch that ensures high reliability. The probe contact is easy to exchange. The connection pin to the contact plate features a rated break point. This protects the touch probe from physical damage due to operator error.

Light sources for your lighting projects Discover our 45W white LED generator with several possible color temperatures for your lighting projects. This generator is equipped with a COB LED. It generates a luminous power identical to that obtained with a 150W metal halide generator.Its light intensity can be adjusted using a built-in potentiometer. It can also be controlled remotely with a 0 - 10V signal. Features of LED 45W generator The 45W LED generator is available in several color temperatures according to the IRC: - IRC90 - 2700K: 3550lm / IRC90 - 3000K: 3780lm - IRC97 - 3000K: 3320lm / IRC90 - 3500K: 3860lm - IRC90 - 4000K: 39400lm / IRC90 - 6000K: 3950lm There is a waterproof version of this IP55 generator.For more details on our generator, consult our technical sheet:

SMD-2.8DIN is stepper driver for small and medium size stepper motors with current per phase up to 2.8A. Driver provide smooth operation, maximum microstepping division is 1/256. Standard logic signals STEP and DIR are used for motion control. Enable signal is also provided and it can be inverted if it is required by a system. Driver SMD-2.8DIN operate with external logic signals source – frequency generator, PLC and etc. The drivers are designed on a modern element base with the use of new engineering solutions, which allow to achieve high speeds while maintaining useful torque. The microstepping division up to 1/256 provides exceptional smoothness and accuracy of positioning, and the output signal FAULT allows monitoring emergency situations that can arise during operation. Additionally, SMD-2.8DIN have the STO function (Safe Torque Off) - which provides motor phases deenergizing in case of any alarm situation.

Light source for starry sky, lighting projects Discover our 20W white LED generator with several possible color temperatures to illuminate your starry skies or lighting projects. This generator is equipped with a COB LED and generates a higher luminous power than that obtained with a 100W halogen generator. Its light intensity can be adjusted using a built-in potentiometer. It can also be controlled remotely with a 0 - 10V signal. Features of LED 20W generator The 20W LED Generator is available in several color temperatures with IRC90: - 2700K, 1470lm / 3000K, 1795lm / 3500K, 1850lm - 4000K, 1850lm / 6500K, 2300 lm There is a waterproof version of this IP55 generator. For more details on our generator, see our datasheet.

The TS workpiece touch probes from HEIDENHAIN help you perform setup, measuring and inspection functions directly on the machine tool. The stylus of a TS touch trigger probe is defl ected upon contact with a workpiece surface. At that moment the TS generates a trigger signal that is transmitted either by cable, an infrared or radio beam to the control. The control simultaneously saves the actual position values as measured by the machine axis encoders, and uses this information for further processing.

The TS workpiece touch probes fromHEIDENHAIN help you perform setup, measuring and inspection functions directly on the machine tool. The stylus of a TS touch trigger probe is defl ected upon contact with a workpiece surface. At that moment the TS generates a trigger signal that is transmitted either by cable, an infrared or radio beam to the control. The control simultaneously saves the actual position values as measured by the machine axis encoders, and uses this information for further processing. HEIDENHAIN touch probes are available in various versions for workpiece measurement on machining centers, milling, drilling, boring machines and CNC lathes.