Small metal parts - Import export

Standard ATprofile with metric pitch (trapezoidal toothing). For manufacturing your own toothed wheels

The angle bracket enables easy mounting of the clamping elements directly on the machine component. The bore D2 serves to hold the clamping element. The clamping element can be mounted on the front or rear of the bracket. The bores D3 enable the bracket to used for other applications.

Housing 1.4308 stainless steel, from size 5 1.4301. Clamping arm 1.4301 stainless steel. Buffer natural rubber. Screw stainless steel A2. Version Housing and lever arm bright. Screw ISO 4017, grade 70, bright. Note Clamping element with integrated highly elastic, shaperetaining natural rubber buffer. Together with a chain tensioner set, sprocket set or a tension pulley, the clamping element makes a readytoinstall tensioning unit suitable for tensioning chain and belt drives. Suitable for both tensioning directions. The clamping elements are maintenancefree and tearoff resistant. The clamping element is fastened to the machine component through a bore. If necessary, a heavyduty dowel pin can be inserted in the positioning notch “P” for torque support.

Tensioner Vesconite® plastic. Screw and nut steel. Version Screw ISO 4017, grade 8.8, electro zincplated. Nut ISO 4035, grade 8, electro zincplated. Note For tensioning roller chains. The chain tensioner set can be combined with all tensioning elements to form a readytoinstall chain clamp. The symmetrical design enables use on both sides. Large radii ensure very quiet running. The highquality plastic does not require any lubrication. The maximum chain speed should not exceed 1.5 m/s in continuous use.

Sprocket steel. Ball bearing chrome steel. Screw and nut steel. Version Sprocket teeth hardened to HRC 50, electro zincplated. Ball bearing with sealing discs 2ZC3. Screw ISO 4017, grade 8.8, electro zincplated. Nut ISO 4035, grade 8, electro zincplated. Note For tensioning roller chains. The sprocket set can be combined with all tensioning elements to form a readytoinstall chain clamp. The ball bearings are sealed both sides, permanently lubricated and maintenancefree. The sprocket can be moved on the screw and thus adapted to the chain track. With the duplex and triplex version, precision spacer sleeves ensure correct chain guidance. Rigid mounting without a tensioning element is also possible. Can also be used as an idler sprocket.

Sprockets for DIN ISO 606 roller chains. The disc sprockets have a centre bore or are predrilled (this can vary due to production methods). For this reason, the dimension D3 max. given in the table is the maximum diameter of the bore that the disc sprockets are supplied with. This pilot hole/centre bore can be customised with a reamed hole, reamed hole with keyway or a tapped hole by the customer. Alternatively, bushes can be fitted by the customer to reduce the diameter.

Sprockets with hub one side for DIN ISO 606 roller chains. The sprockets have a centre bore or are predrilled (this can vary due to production methods). For this reason, the dimension D3 max. given in the table is the maximum diameter of the bore that the sprockets are supplied with. This pilot hole/centre bore can be customised with a reamed hole, reamed hole with keyway or a tapped hole by the customer. Alternatively, bushes can be fitted by the customer to reduce the diameter.

Steel C45. Grey cast iron GG22 from 38 teeth. Sprockets with hub one side for DIN ISO 606 roller chains. The sprockets have a centre bore or are predrilled (this can vary due to production methods). For this reason, the dimension D3 max. given in the table is the maximum diameter of the bore that the sprockets are supplied with. This pilot hole/centre bore can be customised with a reamed hole, reamed hole with keyway or a tapped hole by the customer. Alternatively, bushes can be fitted by the customer to reduce the diameter.

Ready to install sprockets with hub on one side for DIN ISO 606 roller chains. Teeth are milled and inductively hardened. Keyway acc. to DIN 6885 / BS 4235. The keyway is aligned with the tooth tip. With two grub screws. One tapped hole aligned with the keyway centre, the other offset by 90°.

Frame polyamide PA66 GF25 V-0. Elastomer plate EPDM, ozone resistant acc. to DIN 53509, Stage 0 (best stage). Seal TPE TPV. Version: Black. Note: The cable gland plates are suitable for leading through cables without plugs (non-assembled lines). Cables, wires, hoses, pneumatic and hydraulic lines can be routed through. The lines can be inserted without piercing. The elastomer plate adapts to the cables and provides optimum sealing and strain relief. Unused ducts remain securely closed and sealed. Available with different glands or as a blind plate. Rating IP66. Certificates / standards met: UL 514B UL / CSA-File E140310

Steel 1.0718 or stainless steel 1.4305. Version: Electro zinc-plated steel. Bright stainless steel. Note: Pin with groove, suitable for DIN 71752 clevis. Secured with a DIN 6799 E-type circlip (alternatively a KL or SL clip). When combined with a suitable clevis and tang, forms a fully functional clevis joint.

Mounting plate steel/plastic. Monitor bracket aluminium. Bearing washers and sleeves plastic. Mounting flange aluminium. Mounting adapter aluminium. Screws steel. Version: Mounting plate painted. Monitor bracket painted. Mounting flange painted. Mounting adapter painted. Screws electro zinc-plated

Unshielded system. The magnets can be mounted by pressfit or gluing. 1) magnetic face

Hardened to 780 ±40 HV 10 and ground. Without leadin groove. Note All bushes have the bore size marked on the upper face, e.g. 10. Diameters D1 over 15 mm increase in size by 0.5 mm. Dowels or coiled spring pins together with DIN 1731 flathead screws can be used in place of the stop pin.

From diameter D1 over 15 mm size increases are 0.5 mm.

From diameter D1 over 15 mm size increases are 0.5 mm. 1) Chamfer for insert

Housing thermoplastic. Version: Operating principle: Magnetic. Rating: IP67. Note: If the actuator is within the switching range (safety door closed), the safety contacts and, if applicable, the signal contacts of the safety switch are activated. The contact is thus closed via a magnet (magnetic field). Form A: Actuator on one level to the safety switch. Form B: Actuator offset by 90° to the safety switch.

Single-phase primary switched-mode power supply in metal housing. Note: Closed version with screw fittings with contact protection. Overload protection due to current limit, auto recovery. Protected against short-circuit, overload and surges. Power on LED indicator. For DIN top hat rail mounting. Technical data: Rating: IP00 Protection class: I Standard: UL508, TUV EN60950-1, CE Connection: screw terminals with contact protection Fastening: installation on DIN rail TS-35/7.5 or 15

Polyamide fibreglass reinforced. Version: Black. Note for ordering: The connecting elements are supplied in pairs. Note: The connecting elements are used to attach the two ends of the energy supply chain to the installation. Tension relief is integrated into the connecting element. The connecting elements are connected on the outer radius.

Polyamide fibreglass reinforced. Version: Black. Closed. Note: Energy supply chains for safe guiding of flexible electric and data cables as well as pneumatic and hydraulic hoses. The modularly constructed chains can be easily shortened or extended. The material is UV-resistant and therefore also suitable for outdoor applications. Technical data: Technical features in unsupported areas: Speed: 10 m/s Acceleration: 50 m/s²

Cable and housing PUR Contacts gold-plated bronze. Version: Bush (female) Voltage: U max. 60 V Current: I max. 4 A Terminals: 3-pin Security type: IP 67 Note: Plug connector with screw fitting. Plug encapsulated to cable.

Housing, plastic Contacts M8x1 gold-plated bronze. Contacts M12x1 Optaloy-coated brass. Version: Bush (female) Voltage: U max. 60 V Current: I max. 4 A Terminals: 3-pin (4-pin by M12x1) Security type: IP 67 Note: Plug connector for self-assembly with screw lock.

High-strength material mix of thermoplastic/aluminium. Version: Black/bright. Note: We offer three different basic brackets for industrial monitors and touch panels: Compact: space-saving, with a swivel range of 60°. For loads up to 10 kg (static). With universal mounting plate. The basic bracket is suitable for mounting on tubes size Ø30 mm or 30x30 mm. By using the optional reducer sleeve 29040 they can also be mounted on other sized tubes (Ø20 and Ø25 mm or 20x20 and 25x25 mm). With rotary flange: vibration-resistant, lockable monitor bracket with an angle adjustment of 90° in 15° increments. For monitors / control units up to 25 kg (static). With universal mounting plate. The basic bracket is suitable for mounting on tubes size Ø30 mm. By using the optional reducer sleeve 29042 they can also be mounted on other sized tubes (Ø20 and Ø25 mm or 20x20 mm).

Steel 1.0037. Aluminium EN AW-6060. Version: Steel electro zinc-plated. Aluminium anodised. Note: The machined tolerances of these round and square tubes are individually matched to the tube clamping system. *Square aluminium size 10x10 are only available as solid bars. On request: - Custom cut length (L max. 5000 mm) - Stainless steel tube (L max. 3000 mm)

Investment cast 1.4308 stainless steel. ISO 4762 cap screw and ISO 4032 hex nut, stainless steel. From ø30 mm ISO 4017 hex head bolt, stainless steel. Version: Electropolished. Note: The tube clamps with diameters 30 and 40 mm have a silicone sleeve that protects the thread of the hex head screw from contamination and damage. On request: Clamping levers for tightening. Accessory: - Round and square tubes 29050

Thermoplastic. DIN 7984 screws and DIN 985 nuts steel. Version: Black. Screws and nuts electro zinc-plated. Note: The standard size for round tubes is Ø18 mm or Ø30 mm. Use reducer sleeves 29042 if smaller tubes are to be clamped or a conversion from round to square tubes is required. On request: Plastic levers for locking. Accessory: - Reducer sleeves 29042 - Round and square tubes 29050

Material, version: 1. Sealing cap red Polyamide 66 thermoplastic. 2. Filler sieve black Polypropylene thermoplastic. 3 Flange electro zinc-plated steel. 4. Fastening screws electro zinc-plated steel. 5 Flange seal cork. 6. Chain brass.

Material: Aluminium. Version: Bright. Flat seal asbestos-free. On request: Cap marked OIL. Drawing reference: 1) flat seal

Housing fibreglass reinforced thermoplastic polyamide. Sight glass thermoplastic polyamide. O-ring and flat seal NBR. Reflector PVC. Float plastic. Screw and nut, steel. Version: Housing black. Sight glass crystal clear, high mechanical stability, non-ageing. Reflector white. Float red, with magnetic element. Screw and nut electro zinc-plated. Note: The oil level gauge not only enables the oil level to be viewed but also recorded using a REED switch. In addition, the oil level gauges can also emit an electric signal if the temperature of the liquid inside the container reaches the threshold of 70 °C. As soon as the float element approaches the selected minimum value after the circuit has been closed, the system emits an electric signal. The sensor is located on the housing and its height can be adjusted in line with the control requirements for the oil level. The minimum level is ca. 35 mm from the centre of the lower fastening screw.