Nickel - Import export

"The zinc-nickel process has developed in recent years into a process providing one of the most efficient coatings in surface refinement, and is primarily used where high corrosion resistance at a high temperature load is required. Zinc-nickel alloys with 12-16% nickel content are very temperature-resistant, the higher level of hardness compared to the normal zinc coatings is also a very important property, since the risk of damage is lower. The process is related to the conventional alkaline zinc method, but has excellent durability even without post-treatment. This process is suitable for both barrel and rack goods."

Made of nickel-plated brass and plastic

Made of nickel-plated brass with union nut

Stainless steel tubes 1.4301 304L 1.4404 316L 1.4571 316TI, 321, 1.4541 Stainless steel round bars 1.4301 1.4404 1.4571 1.4541 1.4021 1.4006 1.4104 Welded and seamless stainless steel tubes 904L 1.4539 UB6 - Full stainless steel round bars UB6 904L 1.4539 Refractory tubes and round bars 309 1.4828 1.4833 310 310S 1.4841 1.4845- Duplex tubes UNS S31803 1.4462 Super duplex tubes UNS S32750 S32760 1.4410 1.4501 Duplex super duplex full round bars 1.4462 1.4410 1.4501 Stainless steel sheets 1.4301 304L 1.4404 316L 1.4571 316TI, 321, 1.4541 Refractory sheet 309 1.4828 1.4833 310 310S 1.4841 1.4845- Duplex sheets UNS S31803 1.4462 Super duplex sheets UNS S32750 S32760 1.4410 1.4501 Stainless steel sheets UB6 904L 1.4539 Alloy tubes 600; 601; 800; 825 Hastelloy C276 - Tubes and sheets 2.4816; 2.4851; 2.4856; 2.4360 Duplex super duplex stainless steel flanges 904L UB6 1.4539

Spline shafts based on DIN ISO 14 with straight parallel flanks. A spline shaft with spline hub is used to transmit high torques while enabling simultaneous axial movement. The spline shafts are colddrawn. Cold drawing does not interrupt the grain flow of the base material, ensuring spline shafts of very high strength. Tolerances Straightness 0.8 mm/m. Torsion max. 0.5 mm/m. On request Other lengths.

Steel C45. Stainless steel 1.4305. Gunmetal Rg 7. Spline hubs based on DIN ISO 14 with straight parallel flanks. A spline shaft with spline hub is used to transmit high torques while enabling simultaneous axial movement.

Scrap and waste of heat-resistant chromium-nickel steels with a high content of chromium and nickel

Tungsten has a high density, which makes it convenient for ionizing radiation shielding. Despite the higher density compared to traditional and cheaper lead, tungsten shielding is less heavy with equal shielding properties, and more effective if the weight is the same. Tungsten is a very refractory and hard metal, which makes it difficult to process. Therefore, more ductile tungsten alloys with nickel, iron, copper, etc. are used. Cr 16.0%-18.0% We buy alloys of the following grades: VN/VNZh alloys (category: Tungsten 12) (W - 80 - 90% Ni - 5 - 10% Fe - 1- 3%) VD alloys (W - 70 - 80% Cu - 20 - 30%)

Scrap and waste of corrosion-resistant nickel-chromium steels with low nickel content.