Results for
NORELEM FRANCE
France
Also called fixture clamps. The minimal height of this fixture clamp allows numerous clamping problems in fixture and equipment construction to be solved. The brass hex washer offers a gentle yet extremely stable and safe clamping of workpieces. By using several fixture clamps entire pallets can be set-up. “A” = distance from workpiece to screw centre (cam screw). On request: Replacement cam screws.
Request for a quoteNORELEM FRANCE
France
1. Screw the locking screw into the collar bush and fixture clamp and screw onto the baseplate. 2. The workpiece is clamped by tightening the fixture clamp with a spanner. Advantages: Compact design Quick and easy clamping of components Drawing reference: 1) Locking screw 2) Collar bush 3) Fixture clamp
Request for a quoteNORELEM FRANCE
France
Handle electropolished or blasted. Thrust washer, hinge pin and screw bright. Note: The thrust washer face is lightly greased before delivery. The grease is FDA conform and is suitable for use in the foodstuff and pharmaceutical industries.
Request for a quoteNORELEM FRANCE
France
Grip black or traffic red RAL3020. Thrust washer black. Hinge pin bright. Stud and washer trivalent blue passivated or bright stainless steel. Note: Adjustable cam levers are used if the position of the lever relative to the axis of tension only permits one specific position (interference circle). The exact position of the lever is adjusted using a screwdriver on the fine thread setscrew. Plastics are subject to creeping under load (retardation), this can cause reduced clamping force. Drawing reference: 1) setscrew for fine adjustment of lever
Request for a quoteNORELEM FRANCE
France
Handles cast aluminum EN AC-46200. Thrust washer plastic PA 66 GF 35-X fibreglass reinforced. Hinge pin stainless steel 1.4305. Studs and washer steel grade 5.8 or stainless steel 1.4305. Version: Handles fine structured powder-coated, black or red RAL 3003. Thrust washer black. Hinge pin bright. Studs and washer blue passivated steel or bright stainless steel. Note: Plastics are subject to creeping under load (retardation).
Request for a quoteNORELEM FRANCE
France
Race body steel. Wipers plastic/felt. Longitudinal sealing lips rubber. Rollers steel 1.3505. Note Roller carriage with lifetimelubrication roller bearings and wipers which lubricate the system when moving. By simply moving the centre cam roller, the roller carriage can be adjusted so that it is free of play or has the desired pretension in the rail. High travel speeds up to 7 m/s and extremely quiet (faster and quieter than systems that use recirculating balls). The wipers are fitted with an oilsoaked felt. This felt is in constant contact with the track to ensure perfect lubrication. The felts can be recharged using an oil pump through the lubrication points on the front. On request Roller carriages with 4 or 5 rollers.
Request for a quoteNORELEM FRANCE
France
1. Screw the locking screw into the collar bush, fixture clamp and clamping unit and screw onto the baseplate. 2. The workpiece is clamped by tightening the fixture clamp with a spanner. Advantages: Compact design Quick and easy clamping of components Pull-down effect Drawing reference: 1) Locking screw 2) Collar bush 3) Fixture clamp 4) Clamping unit
Request for a quoteNORELEM FRANCE
France
Suitable hinge pin see 04250. The cam lever is an eccentric lever that moves along a logarithmic spiral. Its clamping properties are even over the entire contact surface of the cam.
Request for a quoteNORELEM FRANCE
France
These toe clamps can be used on machine tables or adapter plates. The positive down force holds the workpiece down on the supporting surface. The square washer can adapt slightly to an angular position i.e. the workpiece does not have to be exactly parallel. The clamping washer has a smooth side for machined surfaces and a serrated side for rough faces.
Request for a quoteNORELEM FRANCE
France
Cam-action indexing plungers are used when the indexing pin should not project all the time. Turning the handle through 180° retracts the pin. A notch ensures that the handle remains in this position.
Request for a quoteNORELEM FRANCE
France
Indexing plungers are used where it is necessary to prevent changes of position due to lateral forces. A new locking position can be set only after the plunger has been manually disengaged. With this indexing plunger a cam lever is used to retract the pin. The indexing plunger remains unlocked as long as the handle is positioned over the dead-centre of the cam. The ergonomic cam lever enables light handling with low effort. Temperature range: Permanent operating temperature acc. to IEC 216 max. 160°C. Short-term operating temperature max. 250°C. Advantages: Simple and quick operation. Suitable for high temperature applications. With integrated detent function. On request: Special versions. Accessory: Spacer rings 03089 Positioning bushes for indexing plunger 03099-50 Mounting brackets 03099
Request for a quoteNORELEM FRANCE
France
It is recommended that the cam lever is in a vertical position when the collet is positioned in the bore. The function of the clamping system was tested in bores with tolerance H7. All values for retaining force are guide values and are given without safety factor. The suitability for the respective application must be checked by the user. Advantages: Two components can be joined together without tools. The components are perfectly centred in the clamped state. The compact design means that the mandrel collet with cam lever can even be used in blind holes. There are no specific dimensional requirements for the holes. Additionally, the surfaces and design do not need to have any specific properties. Functional principle: The clamping system is inserted in the hole in the open state. At the beginning of the locking process, the mandrel collet expands and clamps itself in the lower component. The integrated disc spring assembly creates a positive down force
Request for a quoteRM2M
France
The cam-type limit switch is a device used to control the movement of industrial and construction machinery. Information is transmitted via the shaft actuating micro-switches. Standard range BFCN: Gear ratio from 7.5 to 550 Number of cams from 2 to 5 Maximum rotation speed: 500 rpm IP55 Range BFRS: Gear ratio from 10 to 200 Number of cams 2 or 4 Maximum rotational speed: 500 rpm IP55 Options for both ranges: potentiometer, gear wheels, couplings, mounting flange, various cams The micro-switches are either deflection type or with positive opening. The choice between different types of cams allows to modify the reaction curve of the limit switches. On request, specific versions: Up to 12 cams Protection IP66 / 67 /69K Integrated potentiometer or encoder ATEX zone 2 and 21
Request for a quoteINVITRO-CONNECT GMBH
Switzerland
INVITRO-CONNECT GmbH offers various test strategies without animal testing for examining Eye Irritation / Eye damage hazard assessment. From standard regulatory hazard assessments to providing information on the degree of ocular irritation, to discriminating among extremely mild eye area products, INVITRO-CONNECT’ Study Monitors take the time to understand your specific goals and apply the most relevant, cost-effective strategies to achieve them. Tests for Eye Irritation / Eye damage hazard assessment in vitro: HET-CAM Assay BCOP: OECD 437 Isolated Chicken Eye Test: OECD 438 STE / Short Time Exposure (STE, OECD 491): Ocular Irritection EpiOcular & SkinEthic HCE Reconstructed human Cornea-like Epithelium (RhCE): OECD 492 For more information please contact INVITRO-CONNECT GmbH for assistance in developing specialized protocols for your test materials. INVITRO-CONNECT GmbH: Fast Project Execution: personal - competent - reliable --> contact@invitro-connect.com
Request for a quoteINVITRO-CONNECT GMBH
Switzerland
INVITRO-CONNECT GmbH offers various test strategies without animal testing for examining Eye Irritation / Eye damage hazard assessment. From standard regulatory hazard assessments to providing information on the degree of ocular irritation, to discriminating among extremely mild eye area products, INVITRO-CONNECT’ Study Monitors take the time to understand your specific goals and apply the most relevant, cost-effective strategies to achieve them. Tests for Eye Irritation / Eye damage hazard assessment in vitro: HET-CAM Assay BCOP: OECD 437 Isolated Chicken Eye Test: OECD 438 STE / Short Time Exposure (STE, OECD 491): Ocular Irritection EpiOcular & SkinEthic HCE Reconstructed human Cornea-like Epithelium (RhCE): OECD 492 For more information please contact INVITRO-CONNECT GmbH for assistance in developing specialized protocols for your test materials. INVITRO-CONNECT GmbH: Fast Project Execution: personal - competent - reliable --> contact@invitro-connect.com
Request for a quoteTOROID D.O.O.
Slovenia
From a first design study to an advanced FEM analysis. We accompany the development of your Product from the first idea to the final production. Taking advantage of the state-of-the-art Engineering Software, we achieve better results in shorter time.
Request for a quoteTOROID D.O.O.
Slovenia
Sometimes a functional prototype is needed for the design approval. With our in-house 3D Printing Capabilities, an own workshop, and several manufacturing partners, you do not waste any time and resources.
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
TOROID D.O.O.
Slovenia
With our in-house professional prototyping, and a network of our manufacturing Partners, you do not need to look elsewhere. We have a complete range of metal and plastic machining, additive manufacturing, casting, injection molding, welding and product testing available.
Request for a quoteFORMEON
United Kingdom
Reverse engineering involves 3D scanning an existing object to understand its structure, function, and operation, often to replicate or enhance it. It typically starts with 3D scanning to capture precise data, which is then used to create detailed CAD models and reinstate the original design intent.
Request for a quoteResults for
Cam - Import exportNumber of results
20 ProductsCompany type