Belts - Import export

Belt back and belt teeth CR. Tension cords Glascord. Tooth covering mesh polyamide. Note Endless toothed belts with an arched profile as per ISO 13050 with metric pitch. The rounded shape of the tooth contour provides a particularly high degree of safety against incorrect tooth interlocking, combined with a very rounded tooth mesh. Operating noise is significantly reduced by the rounded tooth mesh. The toothed belts are robust, economical and versatile. Belt speed vmax perm. 50 m/s Transmissible power up to 8.42 kW Permissible speed up to 14000 rpm Lownoise and lowmaintenance Very good chemical resistance, particularly against oils, greases and fuels Accurate positioning and angles

Compressor belt drive, V-belt type.

Endless toothed belt with trapezoidal profile to DIN 7721 T1 with metric pitch. Ideal for drives with high belt flexibility. Permits smallest pulley diameters. The toothed belts are intended for drives where precision is a requirement, safety is important and the effects of chemicals are a concern. maintenancefree highpower transmission minimal belt extension accurate positioning and angles very good chemical resistance, especially to oils, greases and fuels extremely high abrasion resistance transmits power up to 30 kW reliable speed up to 10,000 rpm

Aluminium. Rim flanges, steel. Version Aluminium bright. Steel electro zincplated. Note Standard T profile acc. to DIN 7721 T2 with metric pitch (trapezoidal toothing). At least one belt pulley must have a rim flange. The toothed belt pulleys have a centre bore or a pilot hole (this can vary due to manufacturing methods). For this reason, the dimension D2 max. given in the table is the maximum diameter of the bore with which the toothed belt pulleys are supplied. This pilot/centre bore can be amended by the customer to produce a reamed bore, reamed bore with keyway or a tapped hole. Alternatively, customers can also use bushes to reduce the bore diameter.

drylin® ZLW-0630 basic toothed belt axis, basic version, feed rate 54mm/rev, aluminium profile, surface: hard-anodised, neoprene toothed belt in black, guide carriage length 60mm, shaft end support made of aluminium, alignment of drive pin on the right, stepper motor with stranded wire. Configure drylin SHT linear modules individually here: https://igus.eu/ddx

The availability and output of a production system is only as high as the process reliability of its feeding systems allows. Thanks to more than 35 years of experience as a system supplier for assembly technology and custom machines, we can implement a large variety of applications tailored to customers' requirements;

The availability and output of a production system is only as high as the process reliability of its feeding systems allows. Thanks to more than 35 years of experience as a system supplier for assembly technology and custom machines, we can implement a large variety of applications tailored to customers' requirements;

The availability and output of a production system is only as high as the process reliability of its feeding systems allows. Thanks to more than 35 years of experience as a system supplier for assembly technology and custom machines, we can implement a large variety of applications tailored to customers' requirements;

The tension meter is used to perform a pretension test on commercially available belt systems quickly and easily by means of frequency measurement. Fully electronic and equipped with stateoftheart microprocessor technology, the meter enables precise adjustment of all V, toothed and flat belts that have to be tensioned in the range from 10 to 600 Hz. The measurement must never be performed while the drive is running The meter is not permitted or certified for use in potentially explosive areas.

Standard ATprofile with metric pitch (trapezoidal toothing). For manufacturing your own toothed wheels

Standard HTD profile with metric pitch (rounded toothing). At least one toothed belt pulley must have a rim flange. Conical hole for taper clamping bushes. The taper clamping bushes must be ordered separately and are available for various shaft diameters. Pulleys with a taper hole are statically balanced as per ISO 1940 grade G16.

Steel. Toothed pulleys without aluminium rim flanges. Version Steel phosphated. Aluminium bright. Note Standard HTD profile with metric pitch (halfround toothing). At least one belt pulley must have a rim flange. The toothed belt pulleys have a centre bore or a pilot hole (this can vary due to manufacturing methods). For this reason, the dimension D2 max. given in the table is the maximum diameter of the bore with which the toothed belt pulleys are supplied. This pilot/centre bore can be amended by the customer to produce a reamed bore, reamed bore with keyway or a tapped hole. Alternatively, customers can also use bushes to reduce the bore diameter. The pulleys may be recessed on the sides.

The latest generation of color laser printers have four toning stations (CMYK). Paper passes all four stations in one cycle which enables higher print speeds. This design requires precise positioning of the belt with respect to the paper during the toning cycle. This need defines the properties of a seamless belt for a perfect printout: Perfect, defect-free surface Tight tolerances of diameter, length, width and surface roughness Precisely defined electrical conductivity over the entire belt surface KB RollerTech`s capabilities: Diameters: up to 1,000 mm Width: up to 600 mm Thickness: 50 - 100 µm (±10%) Electrical properties: 1E5 - 1E16 Ohm cm Roughness: < 1,0 Ra Primary and Transfer Charge Rollers Charge rollers are critical for long lasting, high quality printouts in laser printers and copiers. KB Roller Tech’s special compounds enable charge rollers to maintain continuously stable electrical properties. Primary charge rollers are mostly soft coated rollers with sensitive surf

Abrasive belt grinder for the cleaning of corner welds and for the creation of spokes on rectangular pieces such as boxes, at double speed it allows to work angles of maximum height 145 mm on a support surface adjustable in height and inclination. Spoking system with two-roller fork on which abrasive belt slides, the adjustable oscillation of the rollers both in the angle and in the fulcrum allow to obtain the desired radius from R = 1 to R = 10 or cleaning with a sharp edge. The adjustment of the plane by means of a handwheel guarantees the best exploitation and correct bending of the belts of adequate width for the height of the piece.

germanWell® corrugated sidewall belts Our germanWell® corrugated sidewall conveyor belts offer high quality and durable solutions where bulk materials have to be transported vertically. By producing sensitive components, corrugated sidewalls from 40 mm to up to 300 mm and cleats from 20 mm to up to 280 mm in height ourselves we are able to ensure that germanWell® corrugated sidewall conveyor belts are of continuously high quality. Individual design and single-piece manufacturing adjust our corrugated sidewall conveyor belts to the intended performance range. germanWell® corrugated sidewall conveyor belts are therefore indispensable in any industry where bulk materials are to be transported vertically as they offer economic benefits and ensure safe and reliable transport. Applications: The possibilities of application of the corrugated sidewall belts reach from the transportation of fine sand to the conveying of lumpy materials. In some fields of application, the properties of these sidewall conveyor belts make them superior to grooved flat belts. ... more

Conveyor Belt Pulleys Drive pulleys Bend pulleys Cage (link) pulleys Shaker pulleys Snub pulleys In serial production: Up to diameters of 610 mm Up to axis lengths of 4,000 mm Everything beyond these dimensions is deemed speciality-made and manufactured to specifications as provided.

Idler Stations 3-parts, throughed

Chevron Conveyor Belts for the Specific Requirements of Steep Angle Transport W (mm) C (mm) P (mm) L (mm) 650 70 250 120 800 145 250 120 1000 245 Standard designs EP 250/2 3.0mm + 1.5mm EP 400/3 4.0mm + 2.0mm

Chevron Conveyor Belts for the Specific Requirements of Steep Angle Transport W (mm) C (mm) P (mm) L (mm) 1000 95 250 120 1200 195 250 120 Standard designs EP 400/3 4.0mm + 2.0mm EP 500/4 4.0mm + 2.0mm EP 630/4 5.0mm + 2.0mm

Chevron Conveyor Belts for the Specific Requirements of Steep Angle Transport W (mm) C (mm) P (mm) L (mm) 1000 75 330 170 1200 175 330 170 Standard designs EP 400/3 4.0mm + 2.0mm EP 500/4 4.0mm + 2.0mm EP 630/4 5.0mm + 2.0mm

Chevron Conveyor Belts for the Specific Requirements of Steep Angle Transport W (mm) C (mm) P (mm) L (mm) 1200 45 330 170 1400 145 330 170 1500 195 330 170 Standard designs EP 400/3 4.0mm + 2.0mm EP 500/4 4.0mm + 2.0mm EP 630/4 5.0mm + 2.0mm

Chevron Conveyor Belts for the Specific Requirements of Steep Angle Transport W (mm) C (mm) P (mm) L (mm) 1200 45 250 120 1400 145 250 120 1500 195 250 120 Standard designs EP 400/3 4.0mm + 2.0mm EP 500/4 4.0mm + 2.0mm EP 630/4 5.0mm + 2.0mm

Idler with precision roller tube and precision groove ball bearing, multiple labyrinth, dust cover, rain cover and grease chamber Support rings and buffer rings Side guiding rollers Holding brackets for lower belt rollers

Speciality products and components Guide discs (for corrugated sidewall belts) with diameters of Ø 300 mm Special idlers Drive shafts and return shafts Pedestal bearings Clamping sets

for the Specific Requirements of Steep Angle Transport Chevron Conveyor Belt Typ GB 330 W (mm) C (mm) P (mm) L (mm) 400 35 250 120 500 85 250 120 650 160 250 120 Standard designs EP 250/2 3.0mm + 1.5mm EP 400/3 4.0mm + 2.0mm

Chevron Conveyor Belts for the Specific Requirements of Steep Angle Transport W (mm) C (mm) P (mm) L (mm) 650 25 330 170 800 100 330 170 1000 200 330 170 Standard designs EP 400/3 4.0mm + 2.0mm EP 500/4 4.0mm + 2.0mm EP 630/4 5.0mm + 2.0mm

Grinding on a belt-grinding machine CNC- and robot-controlled grinding Polishing by hand or by CNC- or robot-controlled rolling machines