Bearing systems - Import export

iglidur® JATM, metric d1 [mm]: iglidur® JATM/VATM consists of a hard-anodized ring and a bearing ring made of iglidur® J (JATM) and iglidur® V400 (VATM). These glide pairings fetch low coefficients of friction and high wear resistance - without lubrication. Special features Maintenance-free plain bearing system For high service performances High stiffening Simple installation Material: iglidur® J High temperature options VATM, iglidur® V400 More dimensions and supplies on request When to use it? When an axial bearing system with defined gliding partners is desired When extremely high wear resistance is required When a very low coefficient of friction is desired When not to use it? When an additional angle compensation is required igubal® axial bearing When little mounting space is available iglidur® J When only sporadic movements are present iglidur® G Y = wear [μm/km] Figure 36.1: The diagram shows the influence of load (p in MPa) and speed (v in m/s) on the wear of the axial bearing. Y= Coefficient of friction Figure 36.2: In the test with different speeds (v) and loads (p) the coefficients of friction of the bearing systems were determined (v in m/s, p in MPa). iglidur® JATM, metric d1 [mm]:

iglidur® PEP, metric d1 [mm]: d2 [mm]: iglidur® PEP, inch d1 [inch]: d2 [inch]: When to use iglidur® PEP plain bearings? When a low-priced plastic plain bearing system is required When freedom is required from shaft material and shaft surface For the protection of expensive and sensitive shafts For extraordinary wear resistance with rare and slow movements. For constantly low coefficients of friction When freedom from corrosion is desired When not to use them? For high surface speeds iglidur® J For high loads iglidur® G iglidur® Q For high temperatures iglidur® V400 iglidur® X iglidur® Z When low-clearance bearings are required iglidur® P iglidur® X Maintenance-free plain bearings usually distinguish themselves by their ability to glide free of lubricants without any further additional layer on the shaft. In these systems it is obvious that shaft materials are as important as the bushings. igus® blazes a new trail with an enclosed and maintenance-free plain bearing concept. iglidur® PEP is an entirely novel lubricant-free plastic plain bearing system with an inner and outer ring. Special feature: The running partner is determined by the inner ring and for the first time, the material and surface finish of the shaft are insignificant. Even thread, rust or scratches do not affect the long-term reliable function. By the specification of the gliding partner and extensive series of tests, the long-term behavior of the bearing system can be precisely forecast. With the PEP polymer plain bearing, the inner ring rotates with the shaft like in ball bearings Relative movements of the shaft to the bearing are dispensed with. This protects the shaft surface from wear and saves costs. Another plus point: Even the most sensitive or unusual materials for the rotating shaft can be used with these new polymer bearings. The PEP polymer bearings are thereby absolutely free from material-dependent corrosion. Wear resistance The wear test results are absolutely convincing with loads up to 5 N/mm². Here the PEP polymer bearings attain values that are virtually comparable with those of the most wear-resistant plastic-steel bearing systems. An exceedingly satisfying result when you consider the costs saved by dispensing with the otherwise essential surface treatment of the shaft. The constantly low friction-coefficient level is also an advantage for the user. As the glide partners are fixed by the defined system, their tribological data too are accurately predictable. The coefficients of friction of the lubricant-free bearing are not determined any more by the shaft materials or surface conditions. If necessary, the coefficients of friction can be further lowered by additional minimum lubrication. Detailed test information with a wide range of lubricants are available and can be had from igus® on request. iglidur® PEP bearings operate independent of the shaft material. iglidur® PEP bearings consists of an inner and outer bearing. X = Load [MPa] Y = Wear [μm/km] A = PEP B = Combination 1 C = Comb. 2 D = Comb. 3 E = Comb. 4 F = Comb. 5 G = Comb. 6 H = Comb. 7 A1 = Wear of the outer bearing B2 = Wear of the inner bearing Fig. 02: Wear tests of various material combinations, p = 0.75 MPa, v = 0.3 m/s X = Load [MPa] Y = Wear [μm/km] A = iglidur® J B = iglidur® PEP Fig. 03: Wear of the iglidur® PEP bearing dependent on the load, v = 0.3 m/s iglidur® PEP, metric d1 [mm]: d2 [mm]: iglidur® PEP, inch d1 [inch]: d2 [inch]: Dimensions according to ISO 3547-1 and special dimensions

DryLin® T linear guide systems were specially developed for applications in automation and handling systems. The design objective was a rugged linear guide for application in the most diverse - and also extreme - environments. They have the same dimensions as most recirculating ball bearing guides. Technical data Gliding elements: Maintenance-free Material: iglidur® J * Max. surface speed: 15 m/s Operating temperature: -40°C to +90°C *Other materials on request 1 Profile rail and base body of the carriage made of aluminum. The rail is hard-anodized, the aluminum base body of the carriage is clear anodized. 2 Six gliding elements made of iglidur® J serve as guide bearings, which are positioned opposite to each other in pairs and make up 3 guide bearings. 3 Alternatively, bearing clearance is continuously adjustable 4 All steel parts are stainless steel 5 The lid is made of solid plastic or stainless steel DryLin® T - Technical data DryLin® T - Clearance adjustment DryLin® TWBM hand clamp DryLin® T - Design rules DryLin® T - Automatic clearance adjustment DryLin® linear guide systems in the cleanroom DryLin® T - Applications DryLin® T - System design DryLin® T - Installation videos System selection & service life calculation DryLin® T - Adjustable clearance The DryLin® T standard version is supplied preset and can be put into operation at once. The user can also manually adjust or fine-tune the clearance of the linear guide. The individual adjustment for your application, as well as the potential to respond to uneven screw surfaces through specific clearance allowance. DryLin® T - Adjustable clearance DryLin® T - Automatic DryLin® T carriages of the automatic version have a mechanism that automatically adjusts the bearing clearance after removal of the preload key. In case a bearing clearance of more than 0.13 mm has to be adjusted during operation, the bearing clearance automatically resets itself when the carriage is completely unloaded. DryLin® T - Automatic DryLin® TW-HKA manual clamp The manual clamp has been developed for simple tasks. The creep behavior of the clamped plastic causes a slackening in clamping force over time (up to 70%). Therefore safety-related parts should not be clamped. Please approach our applications consultant if you require other options for the clamping. DryLin® T - Manual clamping Drylin® T - Heavy Duty This series is used for the most extreme conditions such as dirt, adhesive residues, chips, mud, etc. The plastic gliding elements made of iglidur® J are fixed in the lid and are therefore non-detachable. This system is compatible with many standard commercial recirculating ball bearing systems and is available in the following sizes: TW-01-20, TW-01-25 and TW-01-30. DryLin® T Heavy Duty DryLin® T - Low-profile guide The clearance is not adjustable for the DryLin® T low profile guide rails. The gliding elements are mounted with positive fit in the chromated zinc carriage. This simple and effective design enables guides that are rugged and low-priced at the same time. DryLin® T - Low-profile guide DryLin® T - Compact linear guide This compact linear guide is suitable for rugged use (without clearance adjustment). This system has a slim design and the same dimensions as conventional recirculating ball bearing systems. The plastic gliding elements made of iglidur® J are fixed in the lid and are therefore undetachable. Suitable for DryLin® T guide rail of installation size 20. DryLin® T - Compact linear guide DryLin® TWBM - Manual clamping with high holding force This manual clamping is designed for a long-lasting high holding force of up to 500 N per clamping element. DryLin® TWBM hand clamp DryLin® T clamping elements for rail guide DryLin® T clamping elements for fast positioning by hand or with pneumatics. DryLin® T clamping element DryLin® T linear guide systems were specially developed for applications in automation and handling systems. The design objective was a rugged linear guide for application in the most diverse - and also extreme - environments. They have the same dimensions as most recirculating ball bearing guides. Technical data Gliding elements: Maintenance-free Material: iglidur® J * Max. surface speed: 15 m/s Operating temperature: -40°C to +90°C *Other materials on request 1 Profile rail and base body of the carriage made of aluminum. The rail is hard-anodized, the aluminum base body of the carriage is clear anodized. 2 Six gliding elements made of iglidur® J serve as guide bearings, which are positioned opposite to each other in pairs and make up 3 guide bearings. 3 Alternatively, bearing clearance is continuously adjustable 4 All steel parts are stainless steel 5 The lid is made of solid plastic or stainless steel Advantages: 100 % lubricant-free Adjustable bearing clearance Automatic clearance adjustment High static load capacity Service life up to 50,000 km without lubrication High dirt resistance Low vibration and low noise When not to use ? When you want to save installation space drylin® N drylin® W When you need a pure stainless steel solution drylin® W drylin® R When you want to construct as economical as possible drylin® N drylin® W

Universal glide elements – customise your own plain bearing supported rotary table systems Using the versatile iglidur® PRT universal glide elements, large slewing ring systems can be modeled tailored to the type 01. Depending on the number of elements, rotary table systems can be implemented with inner diameters ranging from approx. 0.5 to 5m. – we will gladly support you with the design and detailed layout. Universal gliding element, made from the proven iglidur® J Customize your own slewing ring tables starting at 500 mm diameters and larger Lubricant free Maintenance-free wear-resistant Rugged Resistant to corrosion Typical applications:Solar industry, assembly equipment, fixture making 1. Glide element made of iglidur® J Part number: JRS-500S/45S Material table General features Density 1,49 g/cm 3 Colour yellow Max. moisture absorption at 23 °C and 50 %r.h. 0,3 Wt.-% Max. water absorption 1,3 Wt.-% Mechanical properties Max. permissible static surface pressure (+20 °C) 35 MPa Shore D hardness 74 Physical and thermal properties Max. long term application temperature 90°C Max. short term application temperature 120°C Lower application temperature –50° Electrical properties Surface resistance >10 12 Ω loads up tp 10 tons

Complement of the lubricant-free delivery programs of screw drives small sizes. With spindles made of stainless steel and nuts made of the self-lubricating high-performance plastic iglidur® J. Application areas:small handlings, lab and medical technology, professional model construction, scanner, printer and locking systems Sleeve bearing with flange

Acoustic insulation materials called Metal Suspended Ceiling Panels or systems are constructed by free seating of aluminum or steel plates on T24 and T15 bearing systems. Plates with different sex and perforation properties are manufactured with 8 mm sag in the carrier profile. Various size and perforation options are used as an aesthetic preference in terms of the different plates and joint effects in addition to the offered plates, easy mounting and demounting features. Stainless Steel Ceiling Panels 30 x 30 special conveyor systems are made by integrating aluminum or steel plates with special claws. Various size and perforation options offer the best solution for suspended ceilings in hospitals and kitchens, as well as the aesthetic and uninterrupted view of plates, joints. Our products have texture and color options. So you can get perfect in ceiling designs.

Oriented Strand Board, OSB for short, is made from orientated layers of small chips, or strands, from fast growing, rapidly renewable trees including Poplar, Aspen and or Pine. These strands are bonded together with a mix of waxes and resins and then compressed under immense pressure to form the boards. Due to its comparatively lower cost and stronger shear strength, when compared to Plywood, OSB has become the construction industry’s panel of choice. OSB is commonly used for sheathing under roofing systems and load bearing wall and roof applications. OSB in and around the home If you are lucky enough to own a shed, you may have noticed OSB board from the inside of your shed roof. However, some larger sheds, or timber built garages, will also have OSB cladding fixed to the inside of the walls. The use of this product, in these situations, is primarily to provide additional structural strength to the structure however, the

Telescopic Slide 57.5 x 34 mm, Galvanized Steel, Standard Length up to 1200 mm, Load Capacity up to 150 kg per Pair Ball Bearing Full Extension, 100% Extension Load Capacity up to 150 kg per Pair Standard Slide Length up to 1200 mm Especially Suitable for Extra-Wide Drawers Manufactured in the European Union For over 40 years, the Schock Group has been developing and manufacturing ball-bearing telescopic slides for linear motion technology. The advantageous physical properties of the ball bearing system form the basis for the high performance of Schock telescopic slides: Smooth and quiet operation, even under high loads. High operational reliability Long service life without maintenance Standard items in the specified lengths are available from our distribution partner SToxxparts GmbH from stock and starting from a quantity of one. Custom solutions are available from Schock Metall on a project-specific basis.

Telescopic slide 70 x 18 mm, galvanized steel, standard length up to 1100 mm, load capacity up to 200 kg per pair. These slides feature full extension with a 100% extension range, providing a smooth and secure linear movement. They are designed for heavy-duty applications and can handle loads of up to 200 kg per pair. The Schock Group has over 40 years of experience in developing and manufacturing ball-bearing telescopic slides for linear motion technology. The advantageous physical properties of the ball bearing guidance system form the basis for the performance of Schock telescopic slides: Smooth and quiet operation, even under high loads. High functional reliability. Long service life without the need for maintenance. Standard items in the specified lengths are available from our distribution partner SToxxparts GmbH from stock, and they can be ordered in quantities as low as one pair.