Electric controls - Import export

THE STABILIZER IMPULSE PSN31000 will ensure minimization of equipment failures, a high level of protection, reduction of energy losses and reduction of downtime for critical consumers for a wide range of applications. IMPULSE PSN31000 can be used not only on production lines, but also to protect equipment in cottages or offices

THE STABILIZER IMPULSE PSN3500 will ensure minimization of equipment failures, a high level of protection, reduction of energy losses and reduction of downtime for critical consumers for a wide range of applications. IMPULSE PSN3500 can be used not only on production lines, but also to protect equipment in cottages or offices

THE STABILIZER IMPULSE PSN3300 will ensure minimization of equipment failures, a high level of protection, reduction of energy losses and reduction of downtime for critical consumers for a wide range of applications. IMPULSE PSN3300 can be used not only on production lines, but also to protect equipment in cottages or offices.

THE STABILIZER IMPULSE PSN3200 will ensure the minimization of equipment failures, a high level of protection, a decrease in energy losses and a decrease in downtime for critical consumers for a wide range of applications. IMPULSE PSN3200 can be used not only on production lines, but also to protect equipment in cottages or offices.

THE STABILIZER IMPULSE PSN3120 will ensure the minimization of equipment failures, a high level of protection, a decrease in energy losses and a decrease in the downtime of critical consumers for a wide range of applications. IMPULSE PSN3120 can be used not only on production lines, but also to protect equipment in cottages or offices.

THE STABILIZER IMPULSE PSN380 will ensure the minimization of equipment failures, a high level of protection, a decrease in energy losses and a decrease in the downtime of critical consumers for a wide range of applications. IMPULSE PSN380 can be used not only on production lines, but also to protect equipment in cottages or offices.

THE STABILIZER IMPULSE PSN330 will ensure the minimization of equipment failures, a high level of protection, a decrease in energy losses and a decrease in the downtime of critical consumers for a wide range of applications. IMPULSE PSN330 can be used not only on production lines, but also to protect equipment in cottages or offices

THE STABILIZER IMPULSE PSN315 will ensure the minimization of equipment failures, a high level of protection, a decrease in energy losses and a decrease in the downtime of critical consumers for a wide range of applications. IMPULSE PSN315 can be used not only on production lines, but also to protect equipment in cottages or offices.

Maintenancefree carbon rollers Independent phase control Efficiency up to 98% (full load) Unique compact size Voltage vector control for high overload capacity Service life 20 years (MTBF)

IEEE 802.3/802.3u/802.3ab/802.3x/802.3at/802.3af, 4 ports PoE 30W 8K MAC, 4Mbit buffer, Switch fabric 12 Gbps, Jumbo Frame 10Kb POE Pin Assignment: 1/2(+), 3/6(-). Mode A EndSpan PoE

IEEE 802.3at/3af, 4 ports PoE 30 | 60 | 95W 4K MAC address, Jumbo Frame 9Kb, Switch fabric 16Gbps POE Pin Assignment: 1/2(+), 3/6(-); 4/5(+), 7/8(-).

IEEE 802.3at/3af (PD Alive Check), 4 ports PoE 30W IGMP snooping; STP, RSTP, MSTP, G.8032 ERPSv2, BPDU Guard; LACP QoS, CoS, DSCP, VLAN (MAC/Protocol-based, PVE, 802.1Q tag, QinQ) Telnet, CLI, Web, SNMP, RADIUS, TACACS+, ACL, DHCP option 82

IEEE 802.3at/3af (PD Alive Check), 8 ports PoE 30/60W IGMP snooping; STP, RSTP, MSTP, MRP, DHCP option 82; LACP QoS, VLAN (Port-based, 802.1Q tag, QinQ), Syslog, Radius Telnet, CLI, Web, SNMP, RMON, Syslog, SSH

IEEE 802.3/802.3u/802.3ab/802.3x/802.3at/802.3af, 4 ports PoE 30W 8K MAC, 1Mbit buffer, Switch fabric 12 Gbps PoE Pin Assignment: 1/2(+), 3/6(-). Mode A EndSpan PoE

IEEE 802.3/802.3u/802.3ab/802.3x/802.3at/802.3af, 8 ports PoE 30W 8K MAC, 4Mbit buffer, Switch fabric 24 Gbps, Jumbo Frame 10Kb POE Pin Assignment: 1/2(+), 3/6(-). Mode A EndSpan PoE

IEEE 802.3af/802.3at/802.3bt (PD Alive Check), 4 ports PoE up to 95W 802.3bt PoE 90W | UPoE(PoH) 95W | 802.3at Standard 36W | Force 60W IGMP snooping; STP, RSTP, MSTP, G.8032 ERPSv2, BPDU Guard; LACP QoS, CoS, DSCP, VLAN (MAC/Protocol-based, PVE, 802.1Q tag, QinQ) Telnet, CLI, Web, SNMP, SSHv1/v2, TLS, SSL, ACL, DHCP option 82

IEEE 802.3at/3af (PD Alive Check), 16 ports PoE 30W IGMP snooping; STP, RSTP, MSTP, G.8032 ERPSv2, BPDU Guard; LACP QoS, CoS, DSCP, VLAN (MAC/Protocol-based, PVE, 802.1Q tag, QinQ) Telnet, CLI, Web, SNMP, RADIUS, TACACS+, ACL, DHCP option 82

NSBox-SUN access node is used to deploy protected autonomous or semi-autonomous outdoor applications in the area with no 24/7 electricity available and solar panels can be installed. Off-grid solar systems work by generating electricity from solar panels and using it to charge a battery via a charger controller. NSBox-SUN contains a charger controller that supports 18-40V solar panels up to 350W and maintains the proper charge of the battery to prevent overcharging and over-discharging. Battery capacity can be up to 200 Ah. The NSBon-51 charge controller is housed in small and rugged DIN rail or mounting panel mountable housing. The controller has three pairs of contacts for connecting the solar panel, battery and load. The front panel contains status LEDs and an integrated temperature sensor. Compensation -56 mV for each degree from 25C, reduces voltage with increasing temperature and vice versa. With temperature compensation charging, charging parameters are automatically adjusted.

Thermoelectric Coolers or Thermoelectric Assemblies are designed to remove heat around critical components within an electrical enclosure with IP66 / NEMA4 protection category. These is a thermoelectric module (thermoelectric air conditioner) using the Peltier effect. The thermoelectric modules create a temperature difference between the internal and ambient heat sinks. It makes internal air colder while heat is dissipating into the external environment. Fans help the transfer of heating from the heat sinks. The main advantages of Thermoelectric Cooler over conventional compressor are: it can be controlled electronically; it is easily reversible when the current is reversed; it can work in harsh environments: in high ambient temperatures or heavily polluted ambient air; in application with vibrations or strong accelerations. Thermoelectric Coolers should be used in regions with hot climates

Electrical and electronic equipment mounted inside a cabinet generate heat that raises the temperature internal air. Over time, the ever increasing heat can cause sensitive devices to malfunctions. Additionally, heat accumulation can cause circuit breakers to trip which can result in system shut down. Fan filter units are used for enclosure climate control to dissipate heat from within the enclosure to prevent the premature failure of the equipment inside it. It helps to increase an operational reliability and a service life for electrical and electronic systems. Filter fans will cool enclosures to a level slightly above the ambient temperature outside the cabinet. To cool enclosure contents, the fans draw filtered ambient air into the cabinet. At the same time, the heated air within the cabinet is blown out an exhaust. The exhaust is also filtered which creates airflow resistance and a slightly higher pressure inside the enclosure.

NSBon-15 and NSBon-14 are surge protectors keeping any IP devices with Ethernet 10/100/1000Base-T interface safe from lightning strike and other forms of electrical interference such as power surges and spikes over networking cables. The devices support PoE transmission in accordance with IEEE 802.3af/3at/3bt recommendations, regardless of the transmission method, as well as passive PoE. The NSBon-15 has eight shielded RJ45 Jacks for connecting four equipment ports. The NSBon-14 has two shielded RJ45 Jack for connecting one equipment port. These protectors utilize Gas Discharge Tubes (GDT) for each wire in RJ45 connector in order to protect all eight wires of networking cable including PoE. The “Line” sockets and the “Equipment” sockets of each port are located on different sides of the case opposite each other. There are also two contacts on the case, GND1 for connection directly to the potential equalization bus (PE) and GND2 for connection to a ground point inside the enclosure.

NSBon-10 is a surge protection device suitable for AC 50/60Hz, rated voltage up to 275V. It protects user's equipment to indirect and direct lightning effect or other transient overvoltage. NSBon-10 surge protector is designed according to IEC 61643-1/GB 18802.1 and can be applied for TNS power supply systems. NSBon-10 is a single DIN-rail mounted module that is easy for installation and maintenance and should be installed close to the protected equipment. NSBon-10 surge protector has a relay output that is shorted until there is no fault and the device is operating properly. The relay is open after internal thermal disconnection device actuation and failure. The device has L,N and PE terminal blocks for wires up to 2,5 sq. mm.

The indoor lighting kit NSBon-06 is suitable for the most types of junction boxes and enclosures. The kit allows to execute repair electrical works (replacement of an Ethernet switch, power supply, batteries) on the installed facility at any time of the day. The system is equipped with a separate circuit breaker. For safe work, you should turn off the main power of the enclosure and all equipment. By default, the lamps are installed in the niches of the top and bottom walls of the cabinet. If necessary, it can be moved to another location. The kit consists of the following components: One or two LED lamps in metal frame with a reflector Magnets for mounting the lamp to a metal surface Circuit breaker and set of wires

The NSBon-01 mounting kit is designed for quick and reliable mounting of the NSB-xxyy | NSP-xxyy | NSV-xxyy | NSE-xxyy series electrical enclosures on circular or rectangular poles. The components of the mounting kit are made of zinc-plated sheet steel and stainless steel. There are two options of lengths of clamping straps, for standard diameter poles up to 190 mm and enlarged diameter up to 300 mm. In the equipment of NSBon-01 includes two mounting rails, two clamping straps, four clamping brackets and the accessories. The pole mounting kit, by default, is designed for 600 mm wide electrical enclosures. By cutting the rail to length or drilling additional holes on the cabinet, the NSBon-01 mounting kit may also be fitted to larger and smaller electrical enclosures.

NSBon-63 4G LTE Cellular Router is highly reliable and secure wireless communications gateway designed for industrial networking. It supports multi-band connectivity including FDD/TDD LTE, WCDMA and GSM for a wide range of applications, such as Industrial IoT, outdoor Video Surveillance Systems and vertical M2M markets. To enhance reliability, NSBon-63 is equipped with dual SIM that supports failover and roaming over to ensure uninterrupted connectivity for mission-critical communications. With flexible LAN/WAN Ethernet options, NSBon-63 allow you to customize your professional applications in diverse environments. It also provides enterprise-grade software features, such as QoS, DMZ, VLAN, OSPF, BGP, RIP-1/2, DDNS, and etc. Featuring VPN Tunnels, Firewall, TR069, and SNMP Trap, NSBon-63 enhance highly secure authentication, encryption and management to protect your data efficiently between public and private networking.

NSBon-59 is a multiband GSM 900/1800 | 4G LTE/ 3G/ WiMax | Wi-Fi antenna suitable for outdoor installation. It is made of UV resistant ABS plastic and can be used together with NSGate NSBox-LTE Outdoor Access Nodes equipped with wireless data transmission devices (4G/LTE routers etc.). NSBon-59 Antenna provides much better bandwidth comparing to antenna installed inside the made of steel cabinet. Steel cabinet walls of a NSBox Access node causes signals to reflect and poor penetration as a result. Therefore, using remote NSBon-59 Antenna is a good solution to achieve stable bandwidth and performance. In order to get better performance, avoid mounting the antenna next to a column or vertical support that could create a shadow zone and reduce the coverage area.

Thermoelectric Coolers or Thermoelectric Assemblies are designed to remove heat around critical components within an electrical enclosure with IP66 / NEMA4 protection category. These is a thermoelectric module (thermoelectric air conditioner) using the Peltier effect. The thermoelectric modules create a temperature difference between the internal and ambient heat sinks. It makes internal air colder while heat is dissipating into the external environment. Fans help the transfer of heating from the heat sinks. The main advantages of Thermoelectric Cooler over conventional compressor are: it can be controlled electronically; it is easily reversible when the current is reversed; it can work in harsh environments: in high ambient temperatures or heavily polluted ambient air; in application with vibrations or strong accelerations. Thermoelectric Coolers should be used in regions with hot climates, to extend the service life of UPS batteries

The NSBon-02 | NSBon-03 are rain hoods | sun shields for the NSB-xxyy | NSV-xxyy series electrical enclosures. Rain hood material is stainless steel. Designed for reliable protection for outdoor siting with water run-off to the rear. Easily retrofitted. Rain hoods are required to prevent settling and building up of liquids, corrosive solids, minerals, dust, dirt and debris on top of an electrical enclosure. If corrosive liquids and solids settle and build up on top of an electrical enclosure, the integrity of the electrical enclosure coating and material may be compromised, which may lead to corrosion and ingress of liquids and solids into the enclosure. The NSBon-02 | NSBon-03 rain hoods are an excellent choice for retrofitting onto electrical enclosures with a flat roof and we generally recommend to use it for outdoor siting.

The NSBon-00 mounting kit is designed for simple and quick installation of additional accessories inside the NSB-xxyy series electrical enclosures. When using the NSBon-00 kit, no mechanical modification of the cabinet is required, for example, additional holes or opening. Additional equipment is mounted on any interior side surface of an enclosure. Installation kit material is zinc-plated sheet steel. Two rows of system perforations provide additional flexibility in the installation of various equipment. The NSBon-00 mounting kit is recommended and used to install the following accessories: Fiber Optic Distribution Frame (ODF); 24VAC power systems NSBon-31/32/33 (transformers); Door-operated switch NSBon-05; Holder for a cable hose or bundle of cables; Vertical system chassis; Additional customer equipment;