Screw caps - Import export

Caps for all categories and all versions. With or without seal, for plastic containers or glass bottles. Also available with sealing film.

Material, version: 1. Sealing cap red Polyamide 66 thermoplastic. 2. Filler sieve black Polypropylene thermoplastic. 3 Flange electro zinc-plated steel. 4. Fastening screws electro zinc-plated steel. 5 Flange seal cork. 6. Chain brass.

Material: Aluminium. Version: Bright. Flat seal asbestos-free. On request: Cap marked OIL. Drawing reference: 1) flat seal

Housing fibreglass reinforced thermoplastic polyamide. Sight glass thermoplastic polyamide. O-ring and flat seal NBR. Reflector PVC. Float plastic. Screw and nut, steel. Version: Housing black. Sight glass crystal clear, high mechanical stability, non-ageing. Reflector white. Float red, with magnetic element. Screw and nut electro zinc-plated. Note: The oil level gauge not only enables the oil level to be viewed but also recorded using a REED switch. In addition, the oil level gauges can also emit an electric signal if the temperature of the liquid inside the container reaches the threshold of 70 °C. As soon as the float element approaches the selected minimum value after the circuit has been closed, the system emits an electric signal. The sensor is located on the housing and its height can be adjusted in line with the control requirements for the oil level. The minimum level is ca. 35 mm from the centre of the lower fastening screw.

Housing steel. Viewing glass thermoplastic polyamide. O-ring and flat seal rubber (NBR). Reflector aluminium. Screw and hex nut steel. Version: Housing painted black. Transparent viewing glass, high mechanical stability, non-ageing, temperature resistant with oil up to 100 °C, with water up to 70 °C. Reflector painted white, markings and scale black. Screw and hexagon nut, electro zinc-plated. Note: The oil level gauges can either be fastened as shown in the illustration or directly in the threaded hole. Centre distance for the fastening holes = L1 ±0.5. The oil level gauges are suitable for tanks operating without pressure. Maximum operating temperature: 100 °C.

Suitable for emergency stop and continuous use Energy reduction: 58% to 73% Dynamic force absorption: 870 N to 35190 N Impact velocity: max. 5 m/s. The profile dampers are maintenance-free and are supplied ready to install with a special fastening screw. Environment: Resistant to microbes, sea water, chemicals and with very good UV and ozone resistance. No water absorption or maceration. Fastening screws: Special cap screws with hex sockets, material 44SMn28 (free-cutting steel SAE 1144) electro zinc-plated: M6x9, M6x10, M8x14, M12x18, M16x26 ISO 4762 cap screws with hex sockets - 8.8 steel, black: M3x6, M4x8**, M5x10** ** With DIN 125 washer, electro zinc-plated steel. Application: Linear slides and linear guides, pneumatic cylinders, handling equipment, machines and plants

500 ml bottle made of durable PE. Ergonomically designed to fit perfectly in your hand. Screw cap with dispenser, ensuring a perfect seal. Available in a wide range of colours. 500 ml ON

Bottle made of RPET, 600ml capacity, BPA free. Stainless steel screw cap, with carrying strap. Available in a wide range of colours. Made from recycled plastic, to encourage the reuse of plastic waste and help the sustainability of the planet. 600 ml RPET/ Stainless Steel

Aluminium bottle with a capacity of 800 ml. With screw-on safety cap and metal carabiner for easy transport. Original matt finish and available in a wide range of colours. Presented in an individual design box. 800 ml Aluminium

tube cap screw material: aluminum alloy 6061-T4 finish: clean and deburred external thread: 1/2-20 UNF 2A size: external diameter 0.750 +/-0.015 inch, length 1.125 +/-0.015 inch socket hex incircle diameter 0.390 +0.010/-0.000 inch, depth 0.31 inch, to accept 3/8” hex key Soochow Advance Industries Co., Ltd., (website: www.sai-parts.com) supplies custom OEM mechanical parts, industrial fasteners, screws, bolts, nuts, industrial fittings, electronic hardware by precision CNC machining, CNC turning, CNC milling, CNC engineering.

Ideal for booth construction, toolbuilding and furniture industry. Please note that diameter A should exceed the bore hole by 0.2 - 0.3 mm. Material: PE Colours: last digits 600 = white last digits 699 = black Further types on written request.

Material: PE Colours: last digits 600 = white last digits 699 = black

Cap with integrated washer that shortens the mounting time considerably and delivers an aesthetic end product. Applicable for M3, M4 and M5 screws. One dimension for several screw sizes! Material: PP Colours: without last digits = white last digits 699 = black V = for countersunk screws / M = for metric screws

Protection against dirt and corrosion. Material: PE Colours: without last digits = black last digit W = white last digits GR = grey Further types on written request.

Protection caps for facade screws (hexagon head screws) with round neoprene slice. Material: PE Colour: black Ø = washer diameter A production according to RAL colour chart or colour sample is possible - please send us your enquiry!

Short version! Protect against dirt and corrosion and are resistant to all weather influences and a lot of chemicals. Applicable with washer. Material: PE Colours: last digits 500 = white without last digits = black

Long version! Protect against dirt and corrosion and are resistant to all weather influences and a lot of chemicals. Applicable without washer. Material: PE Colours: last digits 500 = white without last digits = black

Caps for snap-on rings. These caps are applicable for ring types: 60, 61, 63 and 65. Material: PA 6 Colours: last digits 500 = white last digits 599 = black last digits 002 = grey last digits 076 = brown Cap type 62 suitable for DIN 95, 97, 555, 558, 571, 601, 912, 931, 934, 963, 964, 965, 966, 979, 7963, 7972, 7976, 7982, 7983, 7991, 7995, 7997 ISO 1482, 2009, 2010, 4014, 4016, 4018, 4032, 4034, 4762, 7046, 7047, 7050, 7051, 10642 Dimension A has to match the dimension A of the snap-on rings.

Caps for snap-on rings. These caps are applicable for ring types: 60, 61, 63 and 65. Material: PA 6 Colours: last digits 500 = white last digits 599 = black last digits 002 = grey last digits 076 = brown Cap type 64 suitable for DIN 95, 97, 555, 558, 571, 601, 912, 931, 934, 963, 964, 965, 966, 979, 7963, 7972, 7976, 7982, 7983, 7991, 7995, 7997 ISO 1482, 2009, 2010, 4014, 4016, 4018, 4032, 4034, 4762, 7046, 7047, 7050, 7051, 10642 Dimension A has to match the dimension A of the snap-on rings.

Caps for snap-on rings. These caps are applicable for ring types: 60, 61, 63 and 65. Material: HDPE Colours: last digits 011 = white last digits 114 = black last digits 013 = grey ~RAL7004 last digits 021 = beige ~RAL9001 Cap type 65 suitable for DIN 95, 97, 555, 558, 571, 601, 912, 931, 934, 963, 964, 965, 966, 979, 7963, 7972, 7976, 7982, 7983, 7991, 7995, 7997 ISO 1482, 2009, 2010, 4014, 4016, 4018, 4032, 4034, 4762, 7046, 7047, 7050, 7051, 10642 Dimension A has to match the dimension A of the snap-on rings.

Caps for snap-on rings. These caps are applicable for ring types: 66, 67 and 69. Material: HDPE Colours: last digits 076 = brown ~RAL8019 last digits 027 = brown ~RAL8014 last digits 021 = beige ~RAL9001 last digits 020 = grey ~RAL7038 last digits 018 = grey ~RAL7044 last digits 015 = grey ~RAL7035 last digits 014 = grey ~RAL7001 last digits 013 = grey ~RAL7004 last digits 012 = white ~RAL9016 last digits 011 = white ~RAL9003 without last digits = black ~RAL9005 Cap type 66 suitable for DIN 84, 85, 95, 96, 97, 439, 963, 964, 965, 6912, 7963, 7971, 7972, 7981, 7982, 7983, 7984, 7991, 7995, 7996 ISO 1207, 1481, 1482, 1580, 2009, 2010, 4035, 7046, 7047, 7050, 7051, 10642 Dimension A has to match the dimension A of the snap-on rings.

Caps suitable for hole size 12.0 mm Material: PA Colours: last digits 013 = grey ~RAL7004 last digits 015 = grey ~RAL7035 last digits 021 = white ~RAL9001 last digits 599 = black ~RAL9006 without last digits = white ~RAL9003 Cap type 68 suitable for DIN 84, 85, 96, 439, 6912, 7971, 7981, 7984, 7996 ISO 1207, 1481, 1580, 4035

Washers for snap-on caps. These rings are applicable for cap types: 61, 62, 64 and 65. Material: PA Colours: natural Ring type 60 suitable for DIN 84, 85, 96, 439, 555, 558, 571, 601, 912, 931, 934, 979, 6912, 7971, 7976, 7981, 7984, 7996 ISO 1207, 1481, 1580, 4014, 4016, 4018, 4032, 4034, 4035, 4762, 7049. Dimension A has to match the dimension A of the snap-on caps.

Washers for snap-on caps. These rings are applicable for cap types: 61, 62, 64 and 65. Material: PA Colours: natural Ring type 61 suitable for DIN 84, 85, 96, 439, 555, 558, 571, 601, 912, 931, 934, 979, 6912, 7971, 7976, 7981, 7984, 7996 ISO 1207, 1481, 1580, 4014, 4016, 4018, 4032, 4034, 4035, 4762, 7049. Dimension A has to match the dimension A of the snap-on caps.

Washers for snap-on caps. These rings are applicable for cap types: 61, 62, 64 and 65. Material: PA Colours: natural Ring type 63 suitable for DIN 95, 97, 963, 964, 965, 966, 7963, 7972, 7982, 7983, 7991, 7995, 7997 ISO 1482, 2009, 2010, 7046, 7047, 7050, 7051, 10642. Dimension A has to match the dimension A of the snap-on caps.

Washers for snap-on caps. These rings are applicable for cap types: 61, 62, 64 and 65. Material: PA Colours: natural Ring type 65 suitable for DIN 84, 85, 96, 439, 555, 558, 571, 601, 912, 931, 934, 979, 6912, 7971, 7976, 7981, 7984, 7996 ISO 1207, 1481, 1580, 4014, 4016, 4018, 4032, 4034, 4035, 7049. Dimension A has to match the dimension A of the snap-on caps.

Washers for snap-on caps. These rings are applicable for cap type: 66 Material: PA Colours: natural Ring type 66 suitable for DIN 84, 85, 96, 439, 6912, 7971, 7981, 7984, 7996 ISO 1207, 1481, 1580, 4035. Dimension A has to match the dimension A of the snap-on caps.

Washers for snap-on caps. These rings are applicable for cap type: 66 Material: PA Colours: natural Ring type 67 suitable for DIN 84, 85, 96, 439, 6912, 7971, 7981, 7984, 7996 ISO 1207, 1481, 1580, 4035. Dimension A has to match the dimension A of the snap-on caps.

Washers for snap-on caps. These rings are applicable for cap type: 66 Material: PA Colours: natural Ring type 69 suitable for DIN 95, 97, 963, 964, 965, 7963, 7972, 7982, 7983, 7991, 7995 ISO 1482, 2009, 2010, 7046, 7047, 7050, 7051, 10642. Dimension A has to match the dimension A of the snap-on caps.