Primer coat - Import export

Bitumer Primbit R is a high-quality solvent-based asphalt solution with additives. It is used to prime the surface of a structure before applying the actual asphalt insulation and to maintain corroded concrete surfaces. It is an adhesion-enhancing and priming compound for asphalt masses. •ready for use after mixing, • waterproof, immediately after laying on the surface to be insulated is completely resistant to water flushing, •highly efficient, increases the adhesion of substrates to proper insulation, •perfectly penetrates deep into insulated surfaces, •for application by brush or roofing brush, •has good adhesion to dry substrates (concrete, tar paper, eternit, steel structures, etc.),

Bitumer Primal is a high-quality solvent-based polymer solution with added refiners. It is used to prime mineral surfaces before applying hot-applied bitumen products. The material is also used to preserve corroded concrete surfaces. It is an adhesion- enhancing and priming compound for asphalt compounds, bituminous grouts. USAGE •for making priming and base layers under hot-mix pouring compoundstype N1, N2, N10, • for making anti-corrosion coatings of concrete, • for making coatings that protect mineral surfaces against moisture penetration.

TECHNICAL DEFINITION Interior finishing plaster. Can be used with Airless spray. It provides a fine, uniform and even finish and is easy to sand. COMPOSITION AND APPEARANCE Water, calcium carbonate, resin and various additives. The resulting paste is off-white in colour. COVERINGS Primer coat, paint, wall coverings. TECHNICAL PROPERTIES • Density : 1.8 • Dry extract : 73% STORAGE 18 months in original unopened packaging away from frost and high temperatures. PREPARATION OF SUBSTRATES. Substrates must comply with the DTU 59.1 standard i.e. be dry, clean, dust-free, hard and free of any trace of separating agent. Scrape, brush and remove dust from concrete, plasterboard and plaster tiles. APPLICATION Manual application : With a trowel or filling knife. Mechanical application : Airless and spraying machine. In cold weather, mix the product quickly to aid aspiration. We recommend removing the filter from the pump, spraying at about 80 cm from the substrate.

TECHNICAL DEFINITION Ready-to-use surface filler paste for filling interior holes and cracks. COMPOSITION AND APPEARANCE Water, calcium carbonate, sand, resin and various additives. SUITABLE SUBSTRATES All types of interior substrates : concrete, cellular concrete, cement, breeze block, brick, plasterboard, plaster tiles, plaster, old paint. COVERING Primer coat, smooth surface filler, wall coverings, paint REFERENCE DOCUMENTS • Filler meets EN 16566 standard • DTU 59.1 : Paint work TECHNICAL CHARACTERISTICS • Density : 1.5 • Dry extract : 82 % STORAGE 9 months in original unopened packaging away from frost and high temperatures. PREPARATION OF SUBSTRATES Substrates must comply with the DTU 59.1 standard i.e. be dry, clean, dust-free, hard and free of any trace of separating agent. APPLICATION Applied by hand using a filling knife or spatula. The thickness is 2 cm; to fill deeper holes, build up the filler in several steps The maximum thickness will be 1 cm per coat.

Assembly paste for press-fitting wheels, shafts, tires or bearings Non-stick primer coat for moving threads, guides and slideways to prevent stick-slip effect, seizing and wear Wearing-in lubrication of highly stressed sliding surfaces such as plain bearings, gearwheels, crankshafts with provision of anti-seizing properties Suitable for non-cutting shaping of the difficult type, such as doming, pressing, embossing while avoiding critical metal contacts and welding Advantages and benefits Immediate effective protection against corrosion, wear and stick-slipping under high stress conditions No pressing onto the sliding surface required Highly effective due to the strong affinity of the MoS₂ for metals Extremely low friction at highest loading capability Increased operational reliability of moving parts due to anti-seizing properties Improved performance due to organic molybdenum complex compounds For optimum adhesion, clean contamination and other lubricants

Assembly paste for press-fitting wheels, shafts, tires or bearings Non-stick primer coat for moving threads, guides and slideways to prevent stick-slip effect, seizing and wear Wearing-in lubrication of highly stressed sliding surfaces such as plain bearings, gearwheels, crankshafts with provision of anti-seizing properties Suitable for non-cutting shaping of the difficult type, such as doming, pressing, embossing while avoiding critical metal contacts and welding Advantages and benefits Immediate effective protection against corrosion, wear and stick-slipping under high stress conditions No pressing onto the sliding surface required Highly effective due to the strong affinity of the MoS₂ for metals Extremely low friction at highest loading capability Increased operational reliability of moving parts due to anti-seizing properties Improved performance due to organic molybdenum complex compounds Also available as spray version OKS 221 For optimum adhesion, clean contamination

Mounting paste for press-fitting wheels, shafts, tires or bearings to prevent galling Non-stick primer coat for moving threads, supports, guides and slideways to prevent stick-slip effect Wearing-in lubrication of highly stressed sliding surfaces such as plain bearings, gearwheels, crankshafts with provision of anti-seizing properties In non-cutting shaping of the difficult type, such as doming, pressing, embossing while avoiding critical metal contacts and welding Advantages and benefits Against seizing, wear and stick-slip Highly effective due to the strong affinity of the MoS₂ for metals Extremely low friction at highest loading capability Increased operational reliability of moving parts due to anti-seizing properties Resistant to water, oil, grease, chemicals and hydraulic media Improved performance due to organic molybdenum complex compounds For best adhesion, clean the surfaces from dirt and other lubricants. Best way is to clean mechanically first

- Fully Primed MDF Board. - High quality Moisture Resistant MDF. - Edges sanded after cutting. - Primed all around (inc edges). - Water based primer. - One coat to each face. - Two coats to each edge. - Prompt, precise cutting. - Requires light sanding prior to top coat. - Delivery around 3-7 working days.

Bitumer Primbit W is a solvent-free, water-based bitumen emulsion used for performing anti-moisture and impregnation.Increases adhesion and priming under Elaston 2K and waterproofing compounds. The high dry matter content of about 55 - 60% guarantees the formation of a strong protective coating, resistant to moisture and aggressive substances contained in the soil. Bitumer Primbit W finds its use in: •performing effective, systemic protection moisture protection of roofs, flat roofs, concrete screeds, concrete, basements, baths, terraces, footings and foundations, •performance of priming and undercoating layers under Bitumer Elaston 2K, heat-sealable membranes, asphalt compounds, •can be used as a primer coat prior to the application of bitumen membranes of all brands.Due to its excellent adhesion properties, it provides stronger and space-free adhesion of the surface to the applied bitumen membranes.

General purpose external and internal type welded cabinets, Galvanized sheet body up to 3 mm Body reinforced with special twists High Protection class up to IP66 Strong structure produced with the latest welding technologies Epoxy-Polyester Powder Coating, Primer Painting for External Type applications, Zinc coating solutions against corrosion and oxidation PEM Driven Screw-Nut Applications Flexible cabling and Bus-Bar solutions Low voltage distribution panels in standard sizes, Wall-mounted distribution boxes External Type Device Boxes Machine control consoles Transformer Cabinets Project-based production in special sizes

Our rebated wall panelling dado Rail has been created specifically to fit our MDF Shaker Style Wall Panelling. It comes pre grooved (rebated) on the rear so that it will sit on top of 6mm, 9mm or 12mm MDF Wall panelling kits and low cost, DIY wall panelling packs. If you are looking for a Tongue and Groove MDF wall panelling dado rail then please select 6mm or 9mm. For Bead and Butt MDF panels, please select the 9mm version. The Dado Rail is an exact reproduction moulding made to match one that was used in a Victorian house in Northamptonshire and is supplied in Moisture resistant MDF. Our Dado is easily painted however, it will require sanding prior to the usual two coats of primer/undercoat and two coats of top coat. If you intend to paint your wall paneling with emulsion, to match your walls, the MDF dado rail, and wall panelling, can be painted with the same paint without the need for primer/undercoat.

Zinc-coated galvanized sheets are transformed into painted sheets with various color options through a special surface painting process. Products offered in colors such as RAL9002, RAL3009, RAL7016 are coated with protective film and topcoat paint to achieve a perfect appearance. Technology and Durability Together: The steel sheet surface is reinforced with primer paint and PET film coating processes. The thick PVC-based topcoat offers high flexibility, scratch resistance and styling properties. Plastisol can be safely used indoors and outdoors in roofing, cladding and gutter systems. Areas of Use: Pre-painted sheets are preferred in many sectors from furniture to construction. It combines aesthetics and durability by being used in roll, sheet, trapezoidal, corrugated and embossed shapes. Aesthetics and Protection: Various colors of PPGI add an aesthetic touch to your projects. It also offers a long-lasting and durable material thanks to its zinc coating and protective film.

In the domain of adhesive film and paper production, several techniques can be applied for primer and finish coating. Hannecard supplies rubber, as well as polyurethane roller coverings suited for both water and solvent-based coatings. Depending on the process, the pick-up, transfer or back-up roll can be elastomer coated. All qualities mentioned below are also available in antistatic versions.

Anodizing, galvanizing, passivation, painting: Mifa offers customers all possible surface treatments. A good surface treatment can protect against corrosion, reduces wear or friction, can be electrically insulating or conductive, and in many cases makes the product visually more attractive. Mifa sees surface treatment as the nishing touch that not only increases durability but also adds extra functionality to the aluminium product. The main surface treatments for aluminium that Mifa offers can be roughly divided into three categories: - Conversion layers: aluminium passivation, anodizing, and plasma electrolytic oxidation - Galvanic coatings: chemical nickel-plating, silver, gold, tin, hard chromium etc. - Organic coatings, painting, paint primers, adhesive primers CVD (Chemical Vapour Deposition), PVD (Physical Vapour Deposition), and synergistic coatings can also be applied on request.

Dimensions Thickness: 5 mm up to 150 mm Width: 1000 mm up to 3050 mm Tolerances: EN10029, ASTM A6, ASTM A20, ASME SA6, ASME SA20, DIN 1543, JUS. C. B4. 110 UT Tests: EN 10160:1999 Z quality requirements: EN 10164:1993 Weight and terms of supply: Maximum plate weight is 8 tons 9,5 tons can be produced upon request Flame cutting between 40 to 150 mm thickness Surface conditions: rolled, sandblasted and primer coated High tensile strength plates according to DIN standards can be produced with hardness at - 50 degrees and yield strength at high temperatures, whichever is preferred in other standards.

Victory Lighting mobile infrared paint curing systems offer one of the most cost-effective answers to automotive paint drying presently available. All dryers incorporate the latest technology in short-wave quartz lamps, allowing quick, economical and convenient drying of primers, sealers, top coats, clear lacquers and all water based products. There are several models available, from hand-held units up to a fully automatic temperature feed back large paint dryer covering an area of 2 x 1 metres.

Suitable for any wood indoors and outdoors as well as cork and absorbent substrates (for example plaster). Insulating Primer is a weatherproof, flexible and moisture regulating primer which prevents seepage of wood and cork components. Works especially well on teak, red cedar, oak, larch and cork, as well as pressure treated wood. Water-based and solvent-free our Insulating Primer is particularly well suited for priming for white or bright coats. Insulating Primer masks outgassing of lindane and is also usable for insulating against nicotine, grease and soot- and water stains.

AXLE GROUP: 11 – tonner 3 pcs R:17,5” European Brand (SAF HOLLAND) or Turkish brand. Air Suspension. Tire options, suitable for 17,5” rims. 24 V Electrical system (conforming to European Standards). EBS brake system (2S/2M) in conformity with 71 /320 / EWG or ECR 13 Regulations. Hydraulic or manual operated ramps with appropriate dimensions according to the customers’ preference. Tandem made from ST52 reinforced steel, mounted to chassis and front wall, with 50mm eye and can be adjusted in mechanical system. 650 mm mechanical landing legs. G.W: 23.000 Kgs N.W: 5.000 Kgs Mass W:18.000 Kgs Painting or galvanizing options are available according to the customers’ requests. Main chassis and entire vehicle will be painted in paint oven as Washing + Sandblasting + two coat epoxy primer + two coat acrylic paint 2 x Plastic Wheel Chock Plastic Fenders Reflectors and Anti-spray mud laps conforming to European Standards 42x42mm Reflectors 2 x Lockable Plastic Tool Box

AXLE GROUP: 12 – tonner 4 pcs R:17,5” European Brand (SAF HOLLAND) or Turkish brand / Air Suspension / Tire options, suitable for 17,5” or 22” rims / 24 V Electrical system (conforming to European Standards) / EBS brake system (4S/2M or 4S/3M) in conformity with 71 /320 / EWG or ECR 13 Regulations / Hydraulic or manual operated ramps with appropriate dimensions according to the customers’ preference / 2” 42 CRMO4 Steel King-Pin (in accordance with DIN 74080) or 3,5” 42 CRMO4 Steel King-Pin (in accordance with DIN 74083) are used / 24 Tonner 750 mm or 850mm mechanical landing legs / G.W: 62.000 Kgs N.W: 11.000 Kgs Mass W: 51.000 Kgs Painting or galvanizing options are available according to the customers’ requests. Main chassis and entire vehicle will be painted in paint oven as Washing + Sandblasting + two coat epoxy primer + two coat acrylic paint 1x Plastic Wheel Chock 1x Fire Extinguisher Box 1x Water Tank Reflectors and Anti-spray mud laps conforming to European Standards

Riga Prime Birch plywood (Riga Ply or Riga Paint) overlaid with a primer on one or both faces, thus plywood surface is ready to be painted. It facilitates painting operations and requires less paint. Suitable for exterior or interior application painted as well as unpainted. Advantages Environmentally friendly, easy and fast to paint, less consumption of paint, it does not require priming. The primer coating protects the plywood surface against moisture and burning (scorching) when laser-cutting tools are used. Application Riga Prime can be used as painted as well as unpainted for floors, walls, and ceilings, as packing material and in the manufacture of components of various sizes and shapes. Primer UV hardening primer (PUV-INT) for indoor use Polyurethane primer (PPU-EXT) or UV hardening on water base primer (PUV/WB-EXT) for indoor or outdoor use Coating methods UV hardening primer (PUV-INT) by roller coating method - 1 or 2 overlays (20 - 25 g/m 2 each) Polyurethane primer (PPU-EXT) and UV hardening on water base primer (PUV/WB-EXT) by curtain coating method (120 - 140 g/m 2) Sizes 1200 mm x 2440 / 3050 mm 1250 mm x 2500 / 3000 mm Cut-to-size panels and machining available in accordance with the customers' requirements. Thicknesses 6.5, 9, 12, 15, 18, 21, 24 mm.

AXLE GROUP: 11 – tonner 4 pcs R:17,5” European Brand (SAF HOLLAND) or Turkish brand. Air Suspension. Tire options, suitable for 17,5” rims. 24 V Electrical system (conforming to European Standards). EBS brake system (4S/2M or 4S/3M) in conformity with 71 /320 / EWG or ECR 13 Regulations. Hydraulic or manual operated ramps with appropriate dimensions according to the customers’ preference. SCORPION brand coupling device with added 50mm D 190 KN eye in accordance with European Standards. G.W: 44.100 Kgs N.W: 9.000 Kgs Mass W: 35.100 Kgs Painting or galvanizing options are available according to the customers’ requests. Main chassis and entire vehicle will be painted in paint oven as Washing + Sandblasting + two coat epoxy primer + two coat acrylic paint 2 x Plastic Wheel Chock Plastic Fenders Reflectors and Anti-spray mud laps conforming to European Standards 42x42mm Reflectors

AXLE GROUP: 3pcs 12-tonner R:22.5” Turkish brand drum or disc brake axles / European Brand axles (SAF Holland)/ Structure steels in accordance with TS EN 10025- 2 2004/ Air Suspension / 385/65 R 22.5” - 385/55 R 22.5” tires/ 24 V electrical system (in accordance with European Standards)/ EBS brake system (2S / 2M) in conformity with 71 /320/EWG or ECR 13 Regulations/ 2 “ Steel King-Pin in accordance with DIN 74080 is used/ 24 – tonner 850mm mechanical landing legs/ G.W: 39.000 kgs/ NET WEIGHT: 7.300 kgs/ LADEN MASS WEIGHT: 31.700 kgs Main chassis and entire vehicle will be painted in paint oven as Washing + Sandblasting + two-coat epoxy primer + two-coat acrylic paint. Color will be specified according to the customers’ requests. OPTIONS; Tarpaulin system, according to the customers’ requests Balcony Hydraulically operated rear cover Isolation system for hot materials carriage

AXLE GROUP: 12 – tonner 5 pcs R:22,5” and 10 – tonner 5 pcs R:17,5” European Brand (SAF HOLLAND) or Turkish brand/ Air Suspension/ Tire options, suitable for 17,5” or 22.5” rims/24 V Electrical system (conforming to European Standards)/EBS brake system (4S/3M) in conformity with 71 /320 / EWG or ECR 13 Regulations/ Hydraulic ramps in sizes according to the customers’ requests/ 2” 42 CRMO4 Steel King-Pin (conformin to DIN 74080) or 3,5” 42 CRMO4 Steel King-Pin (in accordance with DIN 74083) are used/ 24 Tonner 750 mm or 850mm mechanical landing legs/ G.W: 72.000 Kgs - N.W: 12.000 Kgs - Mass W: 60.000 Kgs Measurements of vehicle can be designed within min. max. values, in accordance with customers’ requirements. Color will be decided according to the customers’ requests. Main chassis and entire vehicle will be painted in paint oven as Washing + Sandblasting + two coat epoxy primer + two coat acrylic paint 2 x Plastic Wheel Chock 1 x Fire Extinguisher Box 1 x Water Tank Reflectors

AXLE GROUP: 12-tonner 4 pcs R:17,5” European Brand (SAF HOLLAND) or Turkish brand / Air Suspension /Tire options, suitable for 17,5” or 22.5” rims /24 V Electrical system (conforming to European Standards)/ EBS brake system (4S/2M or 4S/3M) in conformity with 71 /320 / EWG or ECR 13 Regulations/ Hydraulic ramps with appropriate dimensions according to the customers’ preference/ 2” 42 CRMO4 Steel King-Pin (in accordance with DIN 74080) or 3,5” 42 CRMO4 Steel King-Pin (conforming to DIN 74083) are used/ 24 Tonner 750 mm or 850mm mechanical landing legs/ G.W: 62.000 Kgs - N.W: 11.000 Kgs Mass W: 51.000 Kgs Measurements of vehicle can be designed within min. max. values, in accordance with customers’ requirements.Color options are available according to customers’ requests.Main chassis and entire vehicle will be painted in paint oven as Washing + Sandblasting + two coat epoxy primer + two coat acrylic paint 1 x Plastic Wheel Chock 1 x Fire Extinguisher Box 1 x Water Tank 42*42mm Reflectors

AXLE GROUP: 11 – tonner 3 pcs R:17,5” European Brand (SAF HOLLAND) or Turkish brand /Air Suspension/ Tire options, suitable for 17,5” rims /24 V Electrical system (conforming to European Standards) / EBS brake system (4S/3M)(4S/2M) in conformity with 71 /320 / EWG or ECR 13 Regulations / Hydraulic or manual operated ramps with appropriate dimensions according to the customers’ preference /Tandem made from ST52 reinforced steel, mounted to chassis and front wall, with 50mm eye and can be adjusted in mechanical system / 650 mm mechanical landing legs. G.W: 33.000 Kgs N.W: 7.500 Kgs Mass W:25.500 Kgs Painting or galvanizing options are available according to the customers’ requests. Main chassis and entire vehicle will be painted in paint oven as Washing + Sandblasting + two coat epoxy primer + two coat acrylic paint 2 x Plastic Wheel Chock Plastic Fenders Reflectors and Anti-spray mud laps conforming to European Standards 2 x Plastic Lockable Tool Box 42x42mm Reflectors

AXLE GROUP: 11 – tonner 3 pcs R:17,5” European Brand (SAF HOLLAND) or Turkish brand. Air Suspension. Tire options, suitable for 17,5” rims. 24 V Electrical system (conforming to European Standards). EBS brake system (4S/3M) in conformity with 71 /320 / EWG or ECR 13 Regulations. Hydraulic or manual operated ramps with appropriate dimensions according to the customers’ preference. SCORPION brand coupling device with added 50mm - D190 KN eye in accordance with European Standards. 650 mm mechanical landing legs. G.W: 31.000 Kgs N.W: 7.500 Kgs Mass W:23.500 Kgs Painting or galvanizing options are available according to the customers’ requests. Main chassis and entire vehicle will be painted in paint oven as Washing + Sandblasting + two coat epoxy primer + two coat acrylic paint 2 x Plastic Wheel Chock Plastic Fenders Reflectors and Anti-spray mud laps conforming to European Standards 42x42mm Reflectors 1 x Steel Tool Box

Wooden Playground Equipment creates safe, social environments for children. 1. Class wooden materials are used for equipment. Wooden playground equipment makes the playgrounds part of its nature and children feel the wooden texture while playing. Wooden, polyethylene, HDPE, rope and metal materials are used for wooden playground equipment. Metal structures undergoes several processes which are sanding, galvanizing, primer polyzing or cataphoresis coating and lastly electrostatic powder painting. Polyethylene pieces are made of colored, anti-static, harmless raw material. Wooden pieces made of impregnated 1. Class wood material.

Wooden Playground Equipment creates safe, social environments for children. 1. Class wooden materials are used for equipment. Wooden playground equipment makes the playgrounds part of its nature and children feel the wooden texture while playing. Wooden, polyethylene, HDPE, rope and metal materials are used for wooden playground equipment. Metal structures undergoes several processes which are sanding, galvanizing, primer polyzing or cataphoresis coating and lastly electrostatic powder painting. Polyethylene pieces are made of colored, anti-static, harmless raw material. Wooden pieces made of impregnated 1. Class wood material.

Wooden Playground Equipment creates safe, social environments for children. 1. Class wooden materials are used for equipment. Wooden playground equipment makes the playgrounds part of its nature and children feel the wooden texture while playing. Wooden, polyethylene, HDPE, rope and metal materials are used for wooden playground equipment. Metal structures undergoes several processes which are sanding, galvanizing, primer polyzing or cataphoresis coating and lastly electrostatic powder painting. Polyethylene pieces are made of colored, anti-static, harmless raw material. Wooden pieces made of impregnated 1. Class wood material.