Power to light - Import export

20m powered by one end with same brightness 22V-30V, wide input voltage range Over heat protected, reverse input protected CRI 90+, 95+ optional NA/ET/EF IP process

Max.length is 30 meters driven by one end Lower current with 48V input，better for longer wire connection Longer for strip using, longer for wiring, higher efficiency with 48V system With less power feed, high cost efficiency, and less risks Ultra long run but samll cut NA/ET/EF/EG IP process

Luminance efficiency up to 130LM/W Constance current design,brightness keeps the same 10 meters running by one end power Suit for commercial stylish lighting with BSD 48V series drivers(under development) Longer for strip using, longer for wiring, higher efficiency with 48V system NA IP process

Reel to reel process, no soldering joint with max.25m 157LM/W，new ErP D class Life span exceeds 60000H Ta: -25~40°C；Tc：75°C（max）

60m long strip driven by one end power supply with the same brightness from end to end Wide range of input voltage/reverse connecting&over temperature protection MAX 60℃operating temperature Longer for strip using, longer for wiring, higher efficiency with 48V system NA/ET/EF/EG IP process

Lighting Busbar Trunking (25A) E-Line KY-S Lighting Busbar Trunking Systems has been designed for buildings and industrial facilitieswhich have lighting and outlet circuits with diminutive electrical machinery and equipment that needs three phase and/or single phase energy requirements with 25A.KY-S Lighting Busbar with its 10A – 16 A tap-off plugs and 32A tap-off boxes are being manufactured by fully automated machines that uses the latest technology in accordance with ISO 9001 and with its quality assurance system certification. Products have been designed in accordance with IEC 61439-6 and tested. Busbar housing are manufactured as pre-galvanized sheets, additionally if requested, it could be manufactured applying RAL 7038 colour.

Lighting Busbar (25A up to 32A) E-Line KAM Series Lighting Busbar Systems has been designed to supply lighting fixtures with electrical current. It can be used to supply power to industrial, decorative or alternate lighting fixtures.

Many people are looking for a high-power headlamp to tackle their needs in their outdoor activities. But they usually don’t know What is the best brand of headlamps? There are many well-known companies that manufacture high-quality headlamps, and each can be considered the best. Our headlamps are top-notch lighting equipment for caving, hiking, camping, mountain biking, inspection, and rescue operations because of their wide beam, motion sensors, remarkable brightness, and illumination range. Let’s discuss the Ronix RH-4284 headlamp with 120LM of max flux and 3w power. Ronix RH-4284 is a high-quality, lightweight, and widely used headlamp with three different modes of high, low, and strobe lighting to cover a wide range of applications. Its housing is constructed from durable ABS plastic to ensure lightweight and convenient usage.

Energy mobility solutions with the Autonomous Lighting Case Portable, waterproof, compact and rechargeable (integrated charger), the BABY self-contained lighting case provides 3500 lumens of LED lighting power - equivalent to a 600W halogen - with consumption reduced to 30W.

The E-Spray is an electric sprayer that works completely autonomously. Power is provided by a lithium-ion battery. Unlike trigger sprayers, no continuous effort is required when pressing the trigger. There is also no need for manual pressurization. A light push on the control button is enough to activate the spraying. - Equipped with chemical resistant EPDM seals - With volume scale on the reservoir - Blue light on sprayer: sufficient battery power - Red light: sprayer needs to be charged - Easy to charge with the included USB cable 1 L: - Also works upside down - Spray nozzle adjustable from mist to straight jet - In the menu accessories/parts you can find nozzles in other colours as well as an ultra-fine nozzle 8 L: - Spray nozzle with cone jet - Shoulder strap included - Lance 40 cm in chemical resistant fiberglass

Extra bright SMD LEDs with up to 2 hours powerful light when battery fully charged. Automatic switch-on in the event of a power failure, when removed from the charger or moved in darkness. PIR sensor with 120° horizontal detection angle and max. 3 m range. When off the charger, can be used as a flashlight with 2 SMD-LEDs or surface light with 16 SMD-LEDs. Installed Li-Ion battery is charged inductively. Charger 230 V, 50 Hz. In blister packaging. LEDs: 16 SMD + 2 SMD Luminous flux: lm front 40 lm / top 60 lm Light duration: h Battery operated max. 2 h Colour: White Measurements: 133 x 63 x 80 mm

The searchlights LED-75/60 are intended for the security lighting of perimeter sites and grounds of different objects. The searchlights are intended for the security lighting of perimeter sites and grounds of different objects. Like all up-to-date LED light sources it assures significant energy saving and high reliability. No stroboscopic effect and collinear optics exclude flare lighting of CCTV cameras and allow to use searchlights for lighting the zones monitored by cameras. It is possible to use different operation modes, for example, full lighting mode, standby mode, switched off. Continuous light flux in all the range of power supply is resistant to low input voltage drops and have no on delay while supplying voltage. High reliability, LEDs lifetime up to 50 000 hours. Remote control via RS-485 interface allows to fade the power of light flux directly from the guard room creating its own level of lighting on the protected sector.

The searchlights LED-40/10 are intended for the security lighting of perimeter sites and grounds of different objects. The searchlights are intended for the security lighting of perimeter sites and grounds of different objects. Like all up-to-date LED light sources it assures significant energy saving and high reliability. No stroboscopic effect and collinear optics exclude flare lighting of CCTV cameras and allow to use searchlights for lighting the zones monitored by cameras. It is possible to use different operation modes, for example, full lighting mode, standby mode, switched off. Continuous light flux in all the range of power supply is resistant to low input voltage drops and have no on delay while supplying voltage. High reliability, LEDs lifetime up to 50 000 hours. Remote control via RS-485 interface allows to fade the power of light flux directly from the guard room creating its own level of lighting on the protected sector.

A Heliport beacon is a powerful light, omnidirectional intended to signal the presence of a heliport. The Heliport beacon flashes in Morse code the letter H. It is used especially when the helipads are surrounded by lights like in a city where it is hard to distinguish the heliports from the other lights. Description Light fixture body: powder-coated aluminum, RAL 1004 (aviation yellow) Diffuser: clear poly-carbonate Cable gland: nickel-plated brass Fasteners: stainless steel Light fixtures are provided with anti condensation valve Light fixtures are UV protected Electrical Characteristics The beacon must be powered and controlled by a special controller which creates the flashing sequence and alow the brightness control. The Heliport Beacon can be also controlled by the main heliport controller. Maximum pick power consumption is 120 W. The average consumption is less than 20W. Optical Characteristics The heliport beacon uses OSRAM White LEDs.

Whether made by a robot or by human hand, wherever things are produced or joined together, you need professional skills, concentration – and above all, good lighting conditions. LINURA.edge delivers powerful, homogeneous white light to monitor processes without specific spectral requirements, for example in assembly systems. Perfect illumination for perfect results. — White light (5000 K/Ra > 80) for the illumination of various types of production processes — ADVANCED package for powerless switching, progressive dimming and automatic dimming when temperature limits are exceeded (at Ta > 50° C) (variants) — Through-wiring for electrical interlinking of several luminaires (variants) — IO-Link interface for the configuration and control of lighting functions such as switching, dimming and flashing, as well as for evaluating diagnostic information and error messages (variants)

Whether made by a robot or by human hand, wherever things are produced or joined together, you need professional skills, concentration – and above all, good lighting conditions. LINURA.edge delivers powerful, homogeneous white light to monitor processes without specific spectral requirements, for example in assembly systems. Perfect illumination for perfect results. - White light (5 000 K / Ra > 80) to illuminate different production processes - Digital input for powerless switching - ADVANCED package for gradual dimming, automatic dimming when temperature limits are exceeded (at Ta > 50 ° C), and for connecting an RGB luminaire (variants) - Through-wiring for electrical interlinking of several luminaires (variants)

For supply and distribution electricity to power and lighting networks with variable voltage 0,660 / 1 kV . Used in the main overhead power line and in residential branching.1. The conductor is twisted by aluminum wires and it is compacted. 2. The insulation is thermo and lightproof . It is also resistant to ultraviolet radiation and ozone effect 3. Neutral conductor is twisted with aluminum solid wires or aluminum wire with steel core and uninsulatedagreed during receiving order from the customerMarking of conductor cores with figures 1, 2, 3. On one of the conductor cores an inscription is made: “JSC Sakcable”, cable brand, manufacture year

Period of use: 100.000 hours Low energy consumption Easy installation Low voltage power supply available Stable light, not affected by voltage variations Housing made of extruded aluminum, for proper thermal management The light fixture consists of: 1 pc. clear diffuser, poly-carbonate or glass (for high temperatures and resistance to chemical environments) 1 pc. Aluminum encasement Optical assembly Fixing system The interior houses an optical block made up an aluminum support and LED(s) All external elements are powder-coated in Airport Yellow – RAL 1004 Electrical Characteristics Electrical insulation class: I Power supply (XXX): 230-110V AC, 12-24V or 48V DC

With a free inner diameter of 45 mm, an outer diameter of 100 mm, a design height of 25 mm and a weight of just 250 g, the LR45 is very compact. The three-dimensional cable outlet on the back enables highly flexible electrical integration of the light. Rear mounting threads and versatile accessories allow uncomplicated mechanical connection to various cameras and sensors. This makes the LR45 the ideal choice for use in confined spaces as well as in motion handling and robot vision systems – even under demanding industrial conditions thanks to IP64 protection. Despite its compact exterior, high-performance integrated controller technology for either continuous, switched or flash operation mode is hidden inside the LR45. In addition, the light has high-speed trigger inputs and the option of brightness control. The irradiance characteristics of the light can be adjusted to the application with the aid of ancillary lenses.

Solar powered street/environment lighting fixture is a lighting fixture designed to be used in park and landscape lighting, industrial facility environmental lighting, to be mounted on poles with a height of 2-4 meters. LED modules with high energy efficiency are used in the luminaires, which have a compact frame structure. It is classified according to solar panel type and LED power, as well as different sizes and dimensions. There are different light distribution and power options according to the area to be illuminated, and design and production can be made according to the project needs. It provides 20% illumination in a still environment and 100% illumination in an active environment. Dim range can be changed with the remote control, armature on-off operation can be performed.