Power relay - Import export

Relay is an automatic switch element with isolation function, which is widely used in remote control, telemetry, communication, automatic control, mechatronics and power electronic equipment.

Relay is an automatic switch element with isolation function, which is widely used in remote control, telemetry, communication, automatic control, mechatronics and power electronic equipment.

✓ Powerful 24 V DC USV (DIN rail version) ✓ Integrated Supercap Pack 13,5kJ ✓ Up to 500 000 cycles ✓ Intelligent input current detection ✓ Regulated output voltage in battery mode ✓ Minimum load detection ✓ Power-fail timer function ✓ Relay dry contact on power fail ✓ Reboot function ✓ Fuel gauge ✓ Shutdown via external signal ✓ Operating temperature range -20°…+70°C ✓ Extended functionality by UPScom management software ✓ 3 years warranty The compact DC UPS modules UPSI-2412DP2 in a robust DIN rail housing are ideally suited for long-term use in control cabinet applications and decentralized solutions for protecting embedded industrial PCs, controls, motor drives, sensors, measurement devices, safety technology and many more. The UPS comes with USB & RS232 interface and provides a capacity of 13.5kJ in up to 500,000 cycles. Extended functionality is available via the UPSGen2 configuration software.

Digital Panel Meter for speed display 96 x 48 mm (B x H) Relais output optional 1/mm for torque and speed measurement of pickups, with speed options. The device series M2 is equipped with a MIN / MAX memory and optional with two relay outputs. The powerful LED's and simple operation via keypad facilitate the handling of the equipment in daily operation. The display of this instrument installation is 5 digits and can be scaled relative to the input frequency.

✓ Uninterruptible power supply (DC UPS) with integrated Li-Ion Battery ✓ Intelligent power sharing ✓ Regulated output voltage in backup mode ✓ Minimum load detection ✓ Power fail Timer-Function ✓ Relay dry contact on power fail ✓ USB & RS232 Interface ✓ Plug&Play - recognized as UPS by operating system ✓ Extended functionality by UPScom management software ✓ Shutdown & Reboot Function ✓ Fuel gauge ✓ Approved to IEC/UL/CSA 61010-1 / -2-201 ✓ 3 years warranty The DC UPS UPSI-2406DP1 with included energy storage has been designed for DIN Rail applications. The robust housing protects electronic parts against coarse pollution. The µC-controlled DC-UPS is based on the proven UPSI-technology and features numerous protective and monitoring functions as well as an integrated reboot function, which activates the auto-restart of the computer system, as soon as the input voltage returns during shutdown or later.

• According to DIN EN 61810-1, DIN EN 60664-1 • Power miniature relay for SMD mounting • High switching power AC 250 V / 5 A • High dielectric strength 4 kV • High limiting continuous current Ith = 5 A • Compact size V = 2,47 cm3 • Safe separation L + K ≥ 5,5 mm EN 50178

Statox 501 PID - the Allrounder PIDs (Photo – Ionisation – Detectors) detect VOCs (Volatile Organic Compounds) in the ppm range, which other sensor types are unable to monitor, like solvents and fuels. A PID sensor uses high energy ultra violet light radiation to break gas molecules into radicals, which are discharged while passing a condenser. The discharge current increases proportional to the number of molecules, i. e. the gas concentration. The standard Statox 501 PID will detect all substances with a ionization energy below 10,6 eV PIDs are normally calibrated with Isobutene. Other gases will be detected with different sensitivity. These so - called response factors must be multiplied with the displayed concentration when adjusting span. Compur Monitors will adjust your Statox 501 PID individually to your application ex works. A magnetic pin gives access to simple parameter setting and calibration menu. A multi - color LED signalises the status of the system. The Statox 501 PID voltage output signal is similar the the signal of a catalytic sensor. The Statox 501 control module displays the measured value and provides an analog output and 3 powerful relay outputs for alarm devices or pcs. Technical Data Material: Housing Interface Cast aluminum, Stainless steel

The iGRAIN Relay Output Unit is a control module designed for automatic control of aeration and head space ventilation fans. The unit is controlled from the iGRAIN Dashboard Manager or control board via RS485 MODBUS. Each unit has 8 relays with NO (Normally Open) and NC (Normally Closed) relay contacts and the status of each relay is indicated with a diode. Each relay unit can be set to an individual address and be installed remotely where the aeration power relays are located. The unit is normally only used for aeration control if there is no PLC/SCADA system available. Advantages • Status and control by iGRAIN Dashboard Manager • Easy control board mount • Operates in either manual or automatic mode via the aeration control software

Our control boxes vary in size and complexity from simple plastic (Polycarbonate or ABS) enclosures incorporating printed circuit boards (PCB’s) to much larger sheet metal or stainless steel enclosures containing far more complicated components like inverters, contactors, transformers, relays, timers and power supply units(PSU’s).