Parallel shaft - Import export

PD / PM series parallel shaft mounted gear units produced with hollow shaft or solid shaft are commonly preferred in conveyor drive systems.

PGR Drive Technologies provide solutions in planet gear units with PTO, IEC, parallel shaft input options which offer high reduction ratio in small volumes in drive systems with heavy and variable loads thanks to their compact and modular structure up to 850000 Nm of moment values.

"Gearmotors are used to convert the torque of a motor. It consists of a speed reducer and an integrated electric motor. Thanks to their compact design, these drives are suitable for many applications. Types of gearmotors offered: - Helical geared motors - Parallel shaft geared motors - Bevel geared motors - Worm geared motors"

Spline shafts based on DIN ISO 14 with straight parallel flanks. A spline shaft with spline hub is used to transmit high torques while enabling simultaneous axial movement. The spline shafts are colddrawn. Cold drawing does not interrupt the grain flow of the base material, ensuring spline shafts of very high strength. Tolerances Straightness 0.8 mm/m. Torsion max. 0.5 mm/m. On request Other lengths.

age 2003 flat pile feeder Vacustar counter MCC 3 6 folding pockets in the parallel fold section following knife shaft 1 folding knife in the cross fold section flatpile delivery Desta BAS-SA 500 Ref: MB230191A Please ask for price. We ship and install worldwide!

Steel C45. Stainless steel 1.4305. Gunmetal Rg 7. Spline hubs based on DIN ISO 14 with straight parallel flanks. A spline shaft with spline hub is used to transmit high torques while enabling simultaneous axial movement.

width 76 cm age 2000 flat pile feeder with Vaculift and Vacubelt counter MPC 6 folding pockets in the parallel fold section following knife shaft 2 folding knives in the cross fold section noise absorbing hood stacking delivery SAP 46 L Delivery time: immediately Ref: MB230192A Please ask for price. We ship and install worldwide!

width 78 cm age 1997 pallet feeder PD 78 6 folding pockets in the parallel fold section following knife shaft 2 folding knives in the cross fold section 1 additional folding pocket after the 1st cross fold noise absorbing hood stacking delivery SBP without compressor Ref: ST230310A Please ask for price. We ship and install worldwide!

width 78 cm age 2001 pallet feeder Tremat sheet-seperation system 4 folding pockets in the parallel fold section following knife shaft 2 folding knives in the cross fold section noise absorbing hood folding knife unit VFZ 52.D stacking delivery SB 66 MP.D without compressors / air supply Ref: HE230275A Please ask for price. We ship and install worldwide!

width 56 cm age 1995 flat pile feeder TREMAT counter PCS 100 6 folding pockets in the parallel fold section following knife shaft 2 folding knives in the cross fold section 1 additional folding pocket after the 1st cross fold noise absorbing hood stream delivery SAK Ref: ST230253A Please ask for price. We ship and install worldwide!

width 56 cm age 1983 flat pile feeder TREMAT 4 folding pockets in the parallel fold section following knife shaft noise absorbing hood 2 folding knives in the cross fold section stream delivery SAK Delivery time: immediately Ref: ST220066A Please ask for price. We ship and install worldwide!

width 76 cm age 2000 flat pile feeder with Vaculift and Vacubelt counter MPC 6 folding pockets in the parallel fold section following knife shaft 2 folding knives in the cross fold section 1 additional folding pocket after the 1st cross fold noise absorbing hood stream delivery ASP 66-2 ME Ref: MB230193A Please ask for price. We ship and install worldwide!

width 66 cm age 2004 pallet feeder Tremat sheet-seperation system 6 folding pockets in the parallel fold section following knife shaft 2 folding knives in the cross fold section 1 additional folding pocket after the 1st cross fold control unit ACC 2.4 window folding pocket pneumatic stream delivery SAK 66 Delivery time: immediately Ref: HE230172A Please ask for price. We ship and install worldwide!

GRF – Geared agitator with parallel shaft geared drive The agitator shaft of the GRF series geared agitator is directly mounted in the hollow shaft of the parallel shaft geared drive. Thus, no additional bearing housing is necessary. The gear bearings are adequately dimensioned and fully adapted to the requirements. The GRF series is suited for a wide range of applications thanks to shaft lengths of up to 6,000 mm and drive ratings of up to 75.0 kW. It has a standard output speed of 1 to 400 rpm. The agitator shafts are balanced for concentric run after assembly of the mixer. Upon request, we supply the GRF series with frequency controlled drive that has drive ratings of up to 7.5 kW. Type test certificate for explosive zone 0.

The agitator shaft of the GRF series geared agitator is directly mounted in the hollow shaft of the parallel shaft geared drive. Thus, no additional bearing housing is necessary. The gear bearings are adequately dimensioned and fully adapted to the requirements. The GRF series is suited for a wide range of applications thanks to shaft lengths of up to 6,000 mm and drive ratings of up to 75.0 kW. It has a standard output speed of 1 to 400 rpm. The agitator shafts are balanced for concentric run after assembly of the mixer. Upon request, we supply the GRF series with frequency controlled drive that has drive ratings of up to 7.5 kW. Type test certificate for explosive zone 0.

The LRD series top-entry sealed agitator can be used for mixing in closed containers with a mechanical seal. It is designed with a coupling housing. The agitator shaft is borne in the bearing housing and the mechanical seal (single- or double-acting). The seal can be exchanged without dismantling the mixer from the tank (also in case of a side entry). Drives with shaft journals for LRD series: Three-phase motor Helical geared drive unit Parallel shaft geared drive unit Variable speed geared drive unit Helical bevel geared drive unit According to the tank size, the LRD series agitator is available in four different frame sizes. Shaft diameters of 30 mm to 90 mm and shaft lengths of up to 10,500 mm are feasible. Explosion protection to ATEX 2014/34/EU for explosive zones 0 to 2 for gases and for explosive zones 20-22 for dusts (device group II, categories 1-3). Pharmaceutical version with FDA and GMP feasible.

The LRE is the most simple solution of an industrial agitator. It consists of a hollow shaft geared drive (worm geared, parallel shaft geared or helical bevel geared drive) and a rigid cast steel bearing housing. Due to this construction high torques are achieved. The agitator shaft is borne within the gear box and the bearing housing and is divided by a flanged coupling below the mounting flange. According to your tank size, the LRE series agitator is available in four different frame sizes. Shaft diameters of 40 mm to 130 mm with lengths of up to 12,000 mm are realized. Sealing housings supplied with shaft seals in various materials are feasible, stuffing boxes or mechanical seals are an alternative. Explosion protection to ATEX 2014/34/EU for explosive zones 0 to 2 for gases and for explosive zones 20-22 for dusts (device group II, categories 1-3).

LRE - Simple top-entry agitator The LRE is the most simple solution of an industrial agitator. It consists of a hollow shaft geared drive (worm geared, parallel shaft geared or helical bevel geared drive) and a rigid cast steel bearing housing. Due to this construction high torques are achieved. The agitator shaft is borne within the gear box and the bearing housing and is divided by a flanged coupling below the mounting flange. According to your tank size, the LRE series agitator is available in four different frame sizes. Shaft diameters of 40 mm to 130 mm with lengths of up to 12,000 mm are realized. Sealing housings supplied with shaft seals in various materials are feasible, stuffing boxes or mechanical seals are an alternative. Explosion protection to ATEX 2014/34/EU for explosive zones 0 to 2 for gases and for explosive zones 20-22 for dusts (device group II, categories 1-3).

TYP A 042 Round pin inserter Description The Streckfuss inserting device Type A 042 offers the economical solution, for the mechanised insertion of round pins, solder posts and or - lugs into p. c. boards. With this device, nearly all customer forms of round pins, solder posts / - lugs can be processed. The loose components are filled into the sorting pot of the vibration conveyor. Trough barriers in the helical of the conveyor, the components are ordered. After positioning, the components are handed to the loading slider, which supplies the components to the inserting tool. Working with this device is save and easy: For assembling, hold the p. c. board with both hands on the edges, and place it under the inserting tool. The p. c. board now lies at the bottom of the pressure stamp, while the tooling pin hole is placed directly under the solder post / - lug shaft looming out of the inserting tool. This has the function of a locating pin. The p. c. board is lifted parallel, so the components shaft enters the tooling pin hole. The insertion process is triggered by a foot switch. Components