Mounting brackets - Import export

The LogTag Wall Mount allows you to hang your LogTag recorder in a safe and neat way. The wall mount can be mounted on a vertical surface such as a wall or a door.

direct mounting to our Gripper Feeds, series ZVTMB or similar products with mounting bracket very costeffective flattening of the coil set best results through adjustment of both top straightening rolls rolls made of special steel and hardened and ground

Shock dampening for low operating noise levels Sturdy, warpresistant design with heavy doublepost guides With adjustable blade clearance for a most precise cut at any thickness Very precise blades made of special steel High operating safety through material guide at entrance and protective cover Springactuated hold down clamp (from 250 mm stock width) Top/bottom dead center control to monitor blade position Counter control Mounting bracket

Shock dampening for low operating noise levels Sturdy, warpresistant design with heavy doublepost guides With adjustable blade clearance for a most precise cut at any thickness Very precise blades made of special steel High operating safety through material guide at entrance and protective cover Springactuated hold down clamp (from 250 mm stock width) Top/bottom dead center control to monitor blade position Counter control Mounting bracket

With threephase servo drive sized according to job requirements Machine body in sturdy clean steel plate design Rollers made of highquality 63 RW tool steel, hardened and polished Pneumatic pilot release with parallel lift of upper roller, guided on gear rack Entry catenary rolls Manual edge guides Simple programming of even complex feeding cycles, Display in cleartext Manual functions for setup such as creep speed, jog mode, single feedtolength Simple memory and recall of job programs for quick changeover Mounting bracket with height adjustment via spindle or hydraulic handpump (optional motorized) Hard chromed or polyurethane coated rollers (optional with Topochrome coating for highgrip feeding) Measuring wheel system for highest feeding accuracy Stroke limitation for faster piloting Fine adjustment of upper roller and strip guiding device for thin stocks (starting at 0,1 mm thickness) Central edgeguides with hand wheel

The angle bracket enables easy mounting of the clamping elements directly on the machine component. The bore D2 serves to hold the clamping element. The clamping element can be mounted on the front or rear of the bracket. The bores D3 enable the bracket to used for other applications.

shock dampening for low operating noise levels thanks to a heavy overall frame and the sturdy, warpresistant design with heavy doublepost guides even toughest materials can be cut smoothly with adjustable blade clearance for a most precise cut at any thickness very precise blades made of special steel high operating safety through material guide at entrance and protective cover springactuated hold down clamp (from 250 mm stock width) top/bottom dead center control to monitor blade position counter control mounting bracket hydraulic power units in different sizes electrical control

Sold in pairs. Fastening material included. Note As an option for floor, platform or side mounting.

The T20 series with toothed output shafts and a rotation angle of 200-220 degrees is ideal for applications where torque generation and higher cycle rates are the most important requirements. Helac’s sliding spline technology with helical teeth is not self-locking and offers both high impact resistance and a high holding torque for demanding applications. It functions both as a rotating device and as a mounting bracket and support structure, so that no external bearing systems, brakes or locking devices are required. Available in three standard sizes with an output torque of up to 6,780 Nm at 210 bar.

SBS suspensions are made of thermoplastic rubber, characterized by increased elasticity, as you can see in the videos below. It helps to mitigate the impact by cushioning when the bed frame is subjected to weight. It is mounted on their struts by being fixed on the bolts (click here) by pressing. The ideal supports for slats with a width of 38 mm are available in several colors and sizes, their role being to ensure increased comfort. The narrowest ones of 3.5 cm are used on the central spar of the bed frame, being fixed on both sides of it, while the medium supports of 5 cm and the widest ones of 6.5 cm are mounted on the outer spars.

Aluminum Extrusion Aluminum Profile for RV Awning Mount Bracket

This spare/replacement wall mounting bracket is compatible with all EL-IOT devices. Your device can be securely screwed into the wall or can be mounted to any magnetic surface using the magnets included. Simply hang your CO2 meter in any location you wish, taking into account the preconditions described in your CO2 meter's user manual.

This dot peen marking range is a marking solution equipped with innovative functionnalities especially developed for integration in production processes PRODUCT ADVANTAGES ROBUST Frame in moulded aluminium. Each axis is fitted with a ball bearing and a transmision system with automatic compensation ERGONOMIC Vertical or horizontal position, easily adaptable to any rackmount configuration due to a connection at the back of the machine. HANDY Mounting connection cable can be connected at the back or on top of the marking head, to facilitate the integration. Three mounting bracket positions are available. FLEXIBLE First integrated marking equipment fitted with a 16 bus card for greater time efficiency and productivity.

The ground mounting system on concrete supports is suitable for rocky terrain where it is not possible to install pile supports. Mounting on the supporting brackets is considered the most practical and economical for standard ground mounting. Moreover, the base does not have a harmful impact on the environment during its operation. All structures are resistant to loads and comply with all European and international standards. Galvanized coating Z600 extends the life of finished products by protecting the steel against corrosion.

Polypropylene feeder for grids in bioreactors and degreasing tanks Suitable for both municipal and industrial wastewater treatment plants. Allows the installation of Aquadisc® 250 / 305 / 320 and Aquatube® 70 diffusers. Diffusers are known for their excellent temperature resistance, recyclability, and longevity. Glass Fibre reinforced polypropylene feeder. Noemi® module body, highly resistant to chemical and abrasive attack - standard length tubes of 2 m, which can be designed to fit many tanks configurations Polypropylene support and fixing brackets mounted on stainless steel anchor rods - the profiled shape of the bracket allows the module body to be locked in rotation and ensures its stability in the tank All stainless-steel fixi Drain plug

The Le Titian picture rail collection, with a simple and discreet design, is preferred when the electrical outlet is located behind the frame to be illuminated. Specially designed, the mounting bracket of the wall light can be directly attached to the frame, thus avoiding the need for multiple holes in the wall.

The Le Titian picture rail collection, with a simple and discreet design, is preferred when the electrical outlet is located behind the frame to be illuminated. Specially designed, the mounting bracket of the wall light can be directly attached to the frame, thus avoiding the need for multiple holes in the wall.

Overview for triflex® advantages Other information triflex® RSP Continuously adjustable retraction force triflex® RSP triflex® RSE Infinitely adjustable retraction force for small robots triflex® RSE Triflex® R-Set Universal module for all motions on the robot Triflex® R-Set Fiber rod modules Intelligent problem solution through directed pretension. Fiber rod modules Universal assembly kit Offers the potential to mount the fiber rod module in the desired position on the robotic arm. Universal assembly kit Strain reliefs for large cross sections Secure mounting also in the use of cables with large cross section. Strain reliefs Gliding feed-through Available with and without swivel bearing Gliding feed-through Protectors Well protected in extreme applications. Protectors Heat shield Protection against weld and metal spills up to 600°C Heat shield CF Robot special cables Special cables for long service life in robotic applications. CF Robot special cables iF-Design Award for "TRC"- and "TRL"-Design Cleanroom environments on request Series TRC electrically conductive ESD/TEX versions possible UL94-V2classification Overview for triflex® advantages Other information Application examples Interesting applications from a variety of industrial sectors Triflex® R Configure interior separation Define cables, select chain and configure interior separation. Now also for all Triflex® R series! Internal separation configurator Triflex® R QuickRobot Equipment support for various types of robots. Simplified ordering of complete systems. QuickRobot TRC.30 Inner height Bi 1: 12 mm Inner height Bi 2: 10 mm Bending radius R: 50 mm Pitch: 11.3 mm e-chain® TRC.40 Inner height Bi 1: 15 mm Inner height Bi 2: 13 mm Bending radius R: 58 mm Pitch: 13,9 mm e-chain® Installation instructions Instructions for the joining and separating of the triflex® R - TRC. Assembly Instructions TRC.60 Inner height Bi 1: 22,5 mm Inner height Bi 2: 19,5 mm Bending radius R: 87 mm Pitch: 20,4 mm e-chain® TRC.70 Inner height Bi 1: 28 mm Inner height Bi 2: 24 mm Bending radius R: 110 mm Pitch: 25,6 mm e-chain® TRC.85 Inner height Bi 1: 33 mm Inner height Bi 2: 28 mm Bending radius R: 135 mm Pitch: 30,6 mm e-chain® TRC.100 Inner height Bi 1: 37.5 mm Inner height Bi 2: 32.5 mm Bending radius R: 145 mm Pitch: 34.5 mm e-chain® TRC.125 Inner height Bi 1: 43,3 mm Inner height Bi 2: 43,3 mm Bending radius R: 182 mm Pitch: 44,6 mm e-chain® Standard mounting bracket for TRC / TRE / TRL. Also possible with strain reliefs and as intermediate connection. Standard mounting brackets Light mounting bracket Standard for the TRL version. Also compatible with TRC / TRE; possible with strain reliefs and as intermediate connection. Light mounting bracket TRCF.85 Inner height Bi 1: 30 mm Bending radius R: 135 mm Pitch: 30.6 mm e-chain® TRCF.100 Inner height Bi 1: 37,5 mm Bending radius R: 145 mm Pitch: 34,5 mm e-chain® Standard mounting bracket for TRC / TRE / TRL. Also possible with strain reliefs and as intermediate connection. Standard mounting brackets Light mounting bracket Standard for the TRL version. Also compatible with TRC / TRE; possible with strain reliefs and as intermediate connection. Light mounting bracket TRE.30 Inner height Bi 1: 12 mm Inner height Bi 2: 10 mm Bending radius R: 50 mm Pitch: 11,3 mm e-chain® TRE.40 Inner height Bi 1: 15 mm Inner height Bi 2: 13 mm Bending radius R: 58 mm Pitch: 13,9 mm e-chain® Installation instructions Instructions for the joining, separating and filling of the triflex® R - TRE. Assembly Instructions TRE.60 Inner height Bi 1: 22,5 mm Inner height Bi 2: 19,5 mm Bending radius R: 87 mm Pitch: 20,4 mm e-chain® TRE.70 Inner height Bi 1: 28 mm Inner height Bi 2: 24 mm Bending radius R: 110 mm Pitch: 25,6 mm e-chain®. TRE.85 Inner height Bi 1: 33 mm Inner height Bi 2: 28 mm Bending radius R: 135 mm Pitch: 30,6 mm e-chain® TRE.100 Inner height Bi 1: 37,5 mm Inner height Bi 2: 32,5 mm Bending radius R: 145 mm Pitch: 34,5 mm e-chain® TRE.125 Inner height Bi 1: 43,3 mm Inner height Bi 2: 43,3 mm Bending radius R: 182 mm Pitch: 44,6 mm e-chain® Standard mounting brackets for TRC / TRE / TRL. Also possible with strain reliefs and as intermediate connection. Standard mounting brackets Light mounting bracket Standard for the TRL version. Also compatible with TRC / TRE; possible with strain reliefs and as intermediate connection. Light mounting bracket TRE.40.B Inner height Bi 1: 15 mm Inner height Bi 2: 13 mm Bending radius R: 58 mm Pitch: 13.9 mm e-chain® TRE.60.B Inner height Bi 1: 22,5 mm Inner height Bi 2: 19,5 mm Bending radius R: 87 mm Pitch: 20,4 mm e-chain® Assembly instruction Instructions for the joining, separating and filling of the Triflex® R - TRE-B version. Assembly instruction TRE.70.B Inner height Bi 1: 28 mm Inner height Bi 2: 24 mm Bending radius R: 110 mm Pitch: 25,6 mm e-chain® TRE.85.B Inner height Bi 1: 33 mm Inner height Bi 2: 28 mm Bending radius R: 135 mm Pitch: 30,6 mm e-chain® TRE.100.B Inner height Bi 1: 37,5 mm Inner height Bi 2: 32,5 mm Bending radius R: 145 mm Pitch: 34,5 mm e-chain® Standard mounting brackets for TRC / TRE / TRL. Also possible with strain reliefs and as intermediate connection. Standard mounting brackets Light mounting bracket Standard for the TRL version. Also compatible with TRC / TRE; possible with strain reliefs and as intermediate connection. Light mounting bracket Assembly tool triflex® R B-version Assembly tool for disassembly of triflex® R B-version Assembly tool triflex® R B-version TRL.30 Inner height Bi 1: 12 mm Inner height Bi 2: 10 mm bending radii R: 50 mm Pitch: 11,3 mm e-chain® TRL.40 Inner height Bi 1: 15 mm Bending radius R: 58 mm Pitch: 13.9 mm e-chain® Installation instructions Instructions for the joining, separating and filling of the Triflex® R - TRL. Assembly Instructions TRL.60 Inner height Bi 1: 23 mm. Bending radius R: 87 mm. Pitch: 20.4 mm e-chain® TRL.70 Inner height Bi 1: 28 mm Bending radius R: 110 mm Pitch: 25.6 mm e-chain® TRL.100 Inner height Bi 1: 38 mm Bending radius R: 145 mm Pitch: 34.5 mm e-chain® Standard mounting brackets for TRC / TRE / TRL. Also possible with strain reliefs and as intermediate connection. Standard mounting brackets Light mounting bracket Standard for the TRL version. Also compatible with TRC / TRE; possible with strain reliefs and as intermediate connection. Light mounting bracket TRLF. 65 Inner height Bi 1: 24.4 mm Bending radius R: 100 mm Pitch: 23.1 mm e-chain® TRLF. 85 Inner height Bi 1: 32.8 mm Bending radius R: 135 mm Pitch: 31 mm e-chain® Assembly instruction Instructions for the joining, separating and filling of the Triflex® R - TRLF. Assembly instruction TRLF. 100 Inner height Bi 1: 38 mm Bending radius R: 145 mm Pitch: 34,5 mm e-chain® Standard mounting brackets for TRC / TRE / TRL. Also possible with strain reliefs and as intermediate connection. Standard mounting brackets Light mounting bracket Standard for the TRL version. Also compatible with TRC / TRE; possible with strain reliefs and as intermediate connection. Light mounting bracket triflex® RSP Continuously adjustable retraction force triflex® RSP triflex® RSE Infinitely adjustable retraction force for small robots triflex® RSE Triflex® R-Set Universal module for all motions on the robot Triflex® R-Set Fiber rod modules Intelligent problem solution through directed pretension. Fiber rod modules Universal assembly kit Offers the potential to mount the fiber rod module in the desired position on the robotic arm. Universal assembly kit Strain reliefs for large cross sections Secure mounting also in the use of cables with large cross section. Strain reliefs Gliding feed-through Available with and without swivel bearing Gliding feed-through Protectors Well protected in extreme applications. Protectors Heat shield Protection against weld and metal spills up to 600°C Heat shield CF Robot special cables Special cables for long service life in robotic applications. CF Robot special cables This system is especially suited for: First choice for multi-axis industrial robots Three versions are available: TRC: closed design; TRE: "Easy" design, very easy to fill in from outside; and TRL: the "Light" version, likewise with "easy" design Universally applicable in general mechanical engineering Secure energy supply system Multi-axis (3D movements) High torsional stability Can be shortened and lengthened as required due to the individual elements Large filling space Doesn't get stuck in the interfering edges Small bending radius Simple cable routing for three-dimensional applications with ball-and-socket system for absorption of high tensile strength Cables easy to install and replace (TRE/TRL version) Fiber rod module for partial reinforcement and to give direction TRL - One-piece element, extremely light High tensile strength without additional elements like steel cables, spring elements, etc. Typical industrial sectors and applications First choice for industrial robots Machine tools Handling equipment 6-axis Material handling system General mechanical engineering iF-Design Award for "TRC"- and "TRL"-Design Cleanroom environments on request Series TRC electrically conductive ESD/TEX versions possible UL94-V2classification

Other information IF -Design Award for Triflex®-Design Torsional movements possible Other information Installation instructions Joining, separating and filling of the Triflex®. Assembly Instructions Application examples Applications in various industrial sectors and in the igus® test laboratory. Triflex® 332.16 Inner height hi: 16 mm Inner width Bi: 16 mm Bending radii R: 38 - 100 mm Pitch: 13.3 mm E-Chain®. 332.32 Inner height hi: 32 mm Inner width Bi: 32 mm Bending radii R: 75 - 250 mm Pitch: 25 mm E-Chain®. 332.50 Inner height hi: 50 mm Inner width Bi: 50 mm Bending radii R: 100 - 250 mm Pitch: 30 mm E-Chain®. 332.75 Inner height hi: 75 mm Inner width Bi: 75 mm Bending radii R: 140 - 300 mm Pitch: 36 mm E-Chain®. 352.50 Inner height hi: 50 mm Inner width Bi: 50 mm Bending radii R: 10 - 250 mm Pitch: 30 mm E-Chain®, snap-open 333.16 Inner height hi: 16 mm Inner width Bi: 16 mm Bending radii R: 38 - 100 mm Pitch: 13.3 mm E-Chain®. 333.32 Inner height hi: 32 mm Inner width Bi: 32 mm Bending radii R: 75 - 250 mm Pitch: 25 mm E-Chain®. 333.50 Inner height hi: 50 mm Inner width Bi: 50 mm Bending radii R: 100 - 250 mm Pitch: 30 mm E-Chain®. 333.75 Inner height hi: 75 mm Inner width Bi: 75 mm Bending radii R: 140 - 300 mm Pitch: 36 mm E-Chain®. 353.50 Inner height hi: 50 mm Inner width Bi: 50 mm Bending radii R: 10 - 250 mm Pitch: 30 mm E-Chain®, snap-open This modular, rugged joint system is suitable for: Three-axis movements for machines of any type For dirt-filled environments High tensile strength Where rectangular shapes are requested Completely closed - reliable protection against dirt and chips Combination of different bending radii and axes Connection and separation possible at any chain Flanged mounting brackets or brackets, galvanized steel Snap-open Series 352 and 353 Combination of Series 353/333 possible Typical industrial sectors and applications Machine tools Robotics Material handling system Plastics industry Construction machinery Vehicle manufacturing Medical equipment IF -Design Award for Triflex®-Design Torsional movements possible

Other information iF-Design Award for easy triflex® Design UL94-V2 classification Torsional movements possible Other information Installation instructions Join, separate and fill the easy triflex®. Assembly Instructions Application examples Applications in various industrial sectors and in the igus® test laboratory. Triflex® E332.25 Inner height hi: 25 mm Inner width Bi: 25 mm Bending radii R: 48 - 200 mm Pitch: 14.5 mm e-chain® E332.32 Inner height hi: 32 mm Inner width Bi: 32 mm Bending radii R: 75 - 250 mm Pitch: 25 mm e-chain® E332.50 Inner height hi: 50 mm Inner width Bi: 50 mm Bending radii R: 100 - 250 mm Pitch: 30 mm e-chain®. E332.75 Inner height hi: 75 mm Inner width Bi: 75 mm Bending radii R: 140 - 300 mm Pitch: 36 mm e-chain® E333.25 Inner height hi: 25 mm Inner width Bi: 25 mm Bending radii R: 48 - 200 mm Pitch: 14.5 mm e-chain® E333.32 Inner height hi: 32 mm Inner width Bi: 32 mm Bending radii R: 75 - 250 mm Pitch: 25 mm e-chain® E333.50 Inner height hi: 50 mm Inner width Bi: 50 mm Bending radii R: 100 - 250 mm Pitch: 30 mm e-chain®. E333.75 Inner height hi: 75 mm Inner width Bi: 75 mm Bending radii R: 140 - 300 mm Pitch: 36 mm e-chain® This modular joint system is especially suited for: Three-axis movements of machines For simple robotic applications Quick installation of cables with "easy" system Simple filling from both sides Where rectangular shapes are required Combination of different bending radii and moving directions Shortening or lengthening possible at "any point" KMA mounting brackets with integrated strain relief Typical industrial sectors and applications Machine tools Robotics Handling equipment Material handling system Plastics industry Construction machinery Vehicle manufacturing General mechanical engineering Medical Equipment Office furniture iF-Design Award for easy triflex® Design UL94-V2 classification Torsional movements possible

Other information E3.10 Inner height hi: 10 mm Inner widths Bi: 20 - 60 mm bending radii R: 15 - 48 mm Pitch: 16,7 mm E-Chain®. E3.15 Inner height hi: 15 mm Inner widths Bi: 20 - 60 mm bending radii R: 32 - 75 mm Pitch: 16,7 mm E-Chain®. E3.22 Inner height hi: 22 mm Inner widths Bi: 20 - 60 mm bending radii R: 44 - 75 mm Pitch: 16,7 mm E-Chain®. iF -Design Award 2005 IPA classification - Report IG0704-400:: ISO Class 1, according to DIN EN ISO 14644-1 for system E3, Series E3.15.040.075.0 at v = 0,5 m/s, 1 m/s, 2 m/s Other information E3.10 Inner height hi: 10 mm Inner widths Bi: 20 - 60 mm bending radii R: 15 - 48 mm Pitch: 16,7 mm E-Chain®. E3.15 Inner height hi: 15 mm Inner widths Bi: 20 - 60 mm bending radii R: 32 - 75 mm Pitch: 16,7 mm E-Chain®. E3.22 Inner height hi: 22 mm Inner widths Bi: 20 - 60 mm bending radii R: 44 - 75 mm Pitch: 16,7 mm E-Chain®. E-Chain® selection aids You can find the right E-Chain® quickly by entering concrete parameters and with the aid of a comparison table. Selection aids Installation instructions Opening and closing of the E-Chain®. Interior separation and strain reliefs. Assembly Instructions Application examples Applications in various industrial sectors and in the igus® test laboratory. E3 system E3: System for highly dynamic applications The cycle times are always shorter in the automation, whereas the requirements in noise reduction, service life, vibration dampening are always higher. For this wide area of small E-Chain®, igus® now introduces the E3 system product range that completely caters to these requirements: Extremely low noise operation (max. 38 dB(A)). The resilient element replaces pins and bores as fastener Modular chain made of three elements Cost-efficient crossbar and separator "on the band" Quicker and easier access to cables by the zipper system Good stability through stable, interlocked links Easy to shorten or lengthen Ideal for flat cables Accessories: Separators, integrated strain reliefs, mounting brackets Typical industrial sectors and applications Production and processing of semiconductors Optics Automatic insertion machines Materials handling technology Measuring technology Printer and plotter Clean room application General mechanical engineering iF -Design Award 2005 IPA classification - Report IG0704-400:: ISO Class 1, according to DIN EN ISO 14644-1 for system E3, Series E3.15.040.075.0 at v = 0,5 m/s, 1 m/s, 2 m/s

Other information Series R48 Inner height hi: 25 mm Inner widths Bi: 25 - 130 mm bending radii R: 60 - 250 mm Pitch: 30,3 mm E-Tube, snap-open along the outer radius Series R58 Inner height hi: 35 mm Inner widths Bi: 50 - 200 mm bending radii R: 75 - 250 mm Pitch: 33,3 mm E-Tube, snap-open along the outer radius Series R68 Inner height hi: 45 mm Inner widths Bi: 50 - 250 mm bending radii R: 100 - 300 mm Pitch: 36 mm E-Tube, snap-open along the outer radius iF-Design-Award for Series R117/R118 and Series R68 ESD classification: Electrically conductive ESD/Atex versions on request UL94-V0 Classifications on request E-Tube made of igumid HT: Hot chips (to 850°C) cannot burn into it. Supplied as a special design on request Other information Series R48 Inner height hi: 25 mm Inner widths Bi: 25 - 130 mm bending radii R: 60 - 250 mm Pitch: 30,3 mm E-Tube, snap-open along the outer radius Series R58 Inner height hi: 35 mm Inner widths Bi: 50 - 200 mm bending radii R: 75 - 250 mm Pitch: 33,3 mm E-Tube, snap-open along the outer radius Series R68 Inner height hi: 45 mm Inner widths Bi: 50 - 250 mm bending radii R: 100 - 300 mm Pitch: 36 mm E-Tube, snap-open along the outer radius E-Chain® selection aids You can find the right E-Chain® quickly by entering concrete parameters and with the aid of a comparison table. Selection aids Installation instructions Joining and separating of the E-Tubes. Assembly Instructions Application examples Applications in various industrial sectors and in the igus® test laboratory. E2 R100 and E2 R Small pitch for silent operation Protection for cables and tubes against chips (even hot chips) Rugged and tight Space-saving with good ratio of inner to outer dimensions Modular interior separation options Small pitch for low-noise, silent operation Very small radii possible through small pitch Smooth, chip-repellant exterior contour Removable lid for shortening the installation time Double stop dog system for longer unsupported lengths KMA mounting brackets with potential for "all-round" fastening Typical industrial sectors and applications Materials handling Construction machinery Machine tools Timber Processing Machines Long travels in many industrial sectors Semiconductor ESD versions Theater and entertaining industry Vehicles General mechanical engineering etc. In all areas exposed to dirt and chips iF-Design-Award for Series R117/R118 and Series R68 ESD classification: Electrically conductive ESD/Atex versions on request UL94-V0 Classifications on request E-Tube made of igumid HT: Hot chips (to 850°C) cannot burn into it. Supplied as a special design on request

Other information Installation video: Instructions for the opening and closing of the E-Tubes Series R117 Inner height hi: 21 mm Inner widths Bi: 20 - 100 mm bending radii R: 63 - 180 mm Pitch: 30,5 mm E-Tube, snap-open along the inner radius on both sides Series R118 Inner height hi: 21 mm Inner widths Bi: 20 - 100 mm bending radii R: 63 - 180 mm Pitch: 30,5 mm E-Tube, snap-open along the outer radius on both sides Series R157 Inner height hi: 40 mm Inner widths Bi: 40 - 200 mm bending radii R: 100 - 250 mm Pitch: 46 mm E-Tube, snap-open along the inner radius on both sides Series R158 Inner height hi: 40 mm Inner widths Bi: 40 - 200 mm bending radii R: 100 - 250 mm Pitch: 46 mm E-Tube, snap-open along the outer radius on both sides Series R167 Inner height hi: 50 mm Inner widths Bi: 50 - 250 mm bending radii R: 100 - 300 mm Pitch: 58,8 mm E-Tube, snap-open along the inner radius on both sides Series R168 Inner height hi: 50 mm Inner widths Bi: 50 - 250 mm bending radii R: 100 - 300 mm Pitch: 58,8 mm E-Tube, snap-open along the outer radius on both sides iF-Design-Award for Series R117/R118 and Series R68 ESD classification: Electrically conductive ESD/Atex versions on request UL94-V0 Classifications on request E-Tube made of igumid HT: Hot chips (to 850°C) cannot burn into it. Supplied as a special design on request Other information Series R117 Inner height hi: 21 mm Inner widths Bi: 20 - 100 mm bending radii R: 63 - 180 mm Pitch: 30,5 mm E-Tube, snap-open along the inner radius on both sides Series R118 Inner height hi: 21 mm Inner widths Bi: 20 - 100 mm bending radii R: 63 - 180 mm Pitch: 30,5 mm E-Tube, snap-open along the outer radius on both sides Series R157 Inner height hi: 40 mm Inner widths Bi: 40 - 200 mm bending radii R: 100 - 250 mm Pitch: 46 mm E-Tube, snap-open along the inner radius on both sides Series R158 Inner height hi: 40 mm Inner widths Bi: 40 - 200 mm bending radii R: 100 - 250 mm Pitch: 46 mm E-Tube, snap-open along the outer radius on both sides Series R167 Inner height hi: 50 mm Inner widths Bi: 50 - 250 mm bending radii R: 100 - 300 mm Pitch: 58,8 mm E-Tube, snap-open along the inner radius on both sides Series R168 Inner height hi: 50 mm Inner widths Bi: 50 - 250 mm bending radii R: 100 - 300 mm Pitch: 58,8 mm E-Tube, snap-open along the outer radius on both sides Installation video: Instructions for the opening and closing of the E-Tubes E-Chain® selection aids You can find the right E-Chain® quickly by entering concrete parameters and with the aid of a comparison table. Selection aids Installation instructions Joining and separating of the E-Tubes. Assembly Instructions Application examples Applications in various industrial sectors and in the igus® test laboratory. E2 R100 and E2 R Chip protection, swivelable Excellent protection against chips (even hot chips) Rugged and tight Snap-open alternately along inside or outside - Swivelable or removable lid, short installation time Space-saving through good internal/external dimensions ratio Modular interior separation options Double stop dog system for longer service life and long, unsupported lengths Universal KMA mounting brackets with potential for "all-round" fastening Typical industrial sectors and applications Machine tools Timber Processing Machines General mechanical engineering etc In all areas exposed to dirt and chips iF-Design-Award for Series R117/R118 and Series R68 ESD classification: Electrically conductive ESD/Atex versions on request UL94-V0 Classifications on request E-Tube made of igumid HT: Hot chips (to 850°C) cannot burn into it. Supplied as a special design on request

The mobile radar is an excellent alternative to the fixed radar to improve the safety of your city's roads. Easily moved and transported with its integrated wheels, this educational radar has the same functions as the traditional preventive radar. It can be seen from a distance thanks to its red and white banners. The photovoltaic panel of this solar radar also allows it to enjoy a greater autonomy and has an internal battery. Directional educational radar with Doppler technology Brightness automatically adjusted according to outside light Speed display in red/green or red/amber (high brightness LEDs) Withstands temperatures from 20°C to 60°C Side mounting bracket with 20° opening angle for optimal solar charging

Hook clamps and clamping screw carbon steel, tempered.

Pipe bracket with rubber inlay

Application: Panel insert for thermocouple and RTD citcuits. Mounting by means of a stainless steel bracket and two screws. Mechanical design: • Housing of fibreglass-filled plastic. • Contacts of original thermocouple materials. • Spring-loaded sockets. • Reverse polarity protection by different pin thicknesses. • Moulded barriers prevent short-circuits. • Screw terminals enable quick connection. • Polarity designation next to the connection screws.

Mounting plate steel/plastic. Monitor bracket aluminium. Bearing washers and sleeves plastic. Mounting flange aluminium. Mounting adapter aluminium. Screws steel. Version: Mounting plate painted. Monitor bracket painted. Mounting flange painted. Mounting adapter painted. Screws electro zinc-plated