Measuring cell - Import export

The pressure transmitters of the 9LD series use the chip-in-oil technology developed by KELLER, uniting a pressure measuring cell, digital temperature compensation and signal processing in a compact housing made of stainless steel or Hastelloy. The transmitters are extremely resistant to environmental influences and delivery highly accurate measurement results as a digital output signal. The I2C interface and the low supply voltages make it easy to integrate in microcontroller-based systems. The extremely low power consumption is ideal for battery-operated devices. The D line is perfect for IoT solutions.

The capacitive pressure transmitters of the 41X series are designed for measuring relative pressure values in the mbar and µbar range. They use digital compensation with a mathematical model to achieve an accuracy of 0,1 %FS – in the temperature range from 10 to 40 °C, this value even corresponds to the total error band. In addition to the digital RS485 interface, the X-line transmitters have a rangeable analog current or voltage output.

The pressure transmitters of the 9LC series use the chip-in-oil developed by KELLER, uniting a pressure measuring cell, digital temperature compensation and signal processing in a compact housing made of stainless steel or Hastelloy. The transmitters are extremely resistant to environmental influences and deliver compensated measurement results as an analog, ratiometric 0,5...4,5V output signal over a wide temperature range.

This miniature force sensor was optimised with respect to its height and is, at only 3.4 mm, the lowest known sensor with strain gage technology. Hardly higher than the diameter of its connection cable, it can also be housed in conditions where space is limited. Along with its minimal geometry, the force sensor is also particularly light. It has a high resonance frequency to follow quickly changing load alternations. Despite its extreme miniaturisation, in its application it remains completely robust and suitable for industry, not only with regard to the highly flexible cable connections or the full welding of sensors for the measurement ranges ≥ 0 … 10 N. The miniature compression force sensors are flat, cylindrical discs with covered bottoms. The central load application button for taking on compression forces is an integrated part of the top, which is the sensor‘s membrane.

The Battery Cell Simulator serves to test Battery Measuring Modules in the 2511 series, which are used in battery module assembly applications (incoming goods inspection, BoL, EoL). The Battery Cell Simulator is able to emulate battery cells of different technologies with resistance and open circuit voltage simulation. The resistance simulation replicates the purely ohmic resistance of a cell. The Battery Cell Simulator runs on 24 V DC. The LED on the front indicates the different operating states. Resistance and voltage values can be defined from standard values or from a custom set of values.

Thanks to its compact shape and three fixing holes on its underside, the 8526 compression load cell can be used in a variety of applications. With its wide choice of measuring ranges from 0 ... 100 N up to 0 ... 1 MN, it really can cover a wealth of measurement tasks, from the laboratory to use in heavy industry. The integral load button provides an easy and reliable means of applying the force to be measured. Angle errors in the load application with a deviation from the measurement axis of up to 3° have only a minor influence on the measurement signal. For ideal measurement accuracy, the load cell should be mounted on a surface that has been ground and has a hardness of at least 60 HRC. The model 8526 load cell is designed with an internal elastic membrane, to which strain gages are attached. When a compressive load is applied to the load cell, the membrane is elastically deformed and transfers its tension to the strain gages.

The load cell measures the compression forces between the circular contact surfaces of plunger and tool. The pin on its top side and hole on its lower face are simply provided for mechanical fixing and centering the components correctly. To provide as large a range of mechanical compatibility as possible, the pins/holes are available in different diameters. Attachments are available which clamp onto the press sensors to enable easy mounting of displacement sensors according to the circumstances of use. FEATURES: — Measuring ranges from 0 … 100 N up to 0 … 25 kN — Small, compact design — Pin/hole diameter from 8 mm to 16 mm — Different diameter for pin and hole can be combined — Mechanical overload protection for all measurement ranges

The measuring element of this load cell consists of a double bending beam with strain gauges, the resistance of which changes with the application of force. Upon applying a voltage to the strain gauge bridge, the change in the strain gauge resistance is converted into output voltage, which is directly proportional to the force. The strain gauges and the entire measuring element are protected from water spray by metal cover including sealing material. The tensile or compressive load to be measured is applied to the sensor element through the M6 threaded hole located on each end face. The load can be applied easily, along the sensor axis. This serves to prevent falsification of the measured values. Overload protection can be realized with little effort using a mechanical stop. FEATURES Measuring ranges from 0 … 20 N to 0 … 880 N Relative non-linearity: ±0.25 % F.S. Many load cycles Protection class IP54 Excellent price-performance ratio burster TEDS optionally available

Due to their small dimensions and sturdy construction, these miniature compression load cells made of stainless steel can be used in a wide range of industrial applications and in laboratories. This compression load cell is easy to handle and its installation is uncomplicated. Its small size makes it perfect for use in very restricted structures for both static and dynamic compression force measurements. The miniature compression load cell model 8415 is a flat cylindrical disc, the bottom of which is closed with a cover. The load application button for receiving the compression forces is an integrated part of the sensor. A strain gage full bridge is applied in the gauging member of the measuring element. This produces bridge output voltage directly proportional to the measured force. The small diameter of the sensors results in high rigidity and a short measurement range. The measuring force has to be applied centrically and free from lateral forces.

Load cell model 8417 measures the tension or compression force between both axially mounted metric exterior threads on the cylindrical sensor housing. Forces are only applied to the threadings, which are especially long, to accommodate counter nuts and must not be affected by external influences such as bending, lateral force or torsion. Any contact with units affixed to the sensor housing - even on the front - must be avoided. The measurement element is a membrane perpendicular to the axis of the sensor with a strain gage full bridge applied to the inner surface, which requires stable excitation with a rated value of approx. 1 mV/V. The connection cable is led radially out of the housing through a sleeve which is used for strain relief. FEATURES: —Measuring ranges from 0 ... 10 N to 0 ... 5 kN —Very small dimensions —Made of stainless steel —Rugged construction —Simple screw mounting —burster TEDS optionally available

This, related to its measuring range, miniaturized load cell enables an universal and reliable operation in industries and laboratories. It is well suited for compression measurements in very restricted structures. The load cell is a compact construction and made of superrefined steel. Therefore it can be used in many fields of industry, like. Examples are: — Press-in force measurements on longitudinal and transversal connections — Compression force measurements on punch and roller applicancy — Spring tension measurements on shock absorbers for cars — Contact pressure determination in push rods — Compression force measurements on compressed-air knee-lever presses Thanks to the rounded top, in shape of a little hat, the force to be measured is led into the sensor centrically and free of lateral force. Specific characteristics: Very small dimensions Drug chain qualified cable Made of stainless steel burster TEDS optionally available

The model 8527 high-precision compression load cell is the ideal load cell for reference measurement chains where highly precise measurement results are required. Its very high production quality and extremely low non-linearity of just 0.035 % F.S. make it a dependable choice for comparative measurements and calibration tasks. Designed for a dynamic stress of up to 100 % of the full scale value, the model 8527 load cell is also suitable for situations where a rapid signal change with high amplitude occurs and has to be measured. The model 8527 high-precision compression load cell has a domed load button on top, onto which the compressive load being measured is applied. Inside the load cell is an elastic membrane, on which strain gages generate a resistance change in the measuring bridge and an output signal proportional to the load. For the best possible measurement results, the force should be applied axially and centrically to the load button.

The measuring element of the load cell consists of a double bending beam on which strain gages are applied. The applied force detunes the measuring bridge so that a proportional output voltage is generated. The strain gages on the measuring element are protected against dirt and water spray by a rubber bellows. The sensor can be easily mounted via two mounting holes. The tension or compression force to be measured is introduced at the opposite end perpendicular to the sensor axis. Due to its special design, the influence by an extension (e.g. touch finger) on the measuring signal is low. Overload protection can be realized with little effort using a mechanical stop. FEATURES For tension and compression forces Measuring ranges from 0 ... 5 N to 0 ... 2 kN Relative non-linearity: ≤ ±0.1 % F.S. Very low mounting height Simple force application Material aluminium or stainless steel Special design on request burster TEDS optionally available

The Load cell model 8451 has been developed for measuring the forces that occur during press operation. The internal measuring elements have a rugged design, which mean they can cope reliably with the steep force curves that are typical of press applications. They can be fitted or replaced quickly and easily on the press ram without the need for additional components around them. The force sensor is placed between the tool and the press ram and can thus measure the actual compression force directly in the axis of operation. The load cell measures the compression forces between the circular contact surfaces of plunger and tool. The pin on its top side and hole on its lower face are simply provided for mechanical fixing and centering the components correctly. The connecting cables are suitable for drag chains, designed for many movements and stably fastened in the sensor housing.

The low-cost OEM pressure transducers of the 6M series are based on a piezoresistive measuring cell with a brazed metal diaphragm in a brass housing.

The low-cost OEM pressure transducers of the 6S series are based on a piezoresistive measuring cell with a brazed metal diaphragm in a steel housing.

The force measuring chain has been developed for applications where the requirements for precision are not the primary focus, but rather where an economical purchase price and simple functionality are the key criteria. The sensor‘s strain gauge technology allows both static and dynamically changing forces to be measured. The large display means that the force acting on the sensor can be read easily. The four integrated threaded holes allow the sensor to be integrated quickly and easily into existing production and assembly equipment. Typical applications include: —Testing the strength of welded joints —Sports medicine —Monitoring the clamping force of hose connections The body of the sensor is a flat, cylindrical disk, into which a domed force application knob is integrated. It is important that the force is applied axially to the center of the sensor.

The level sensors of the 46X series combine a ceramic measuring cell for very low measuring ranges on the mbar scale with microprocessor electronics for compensating for temperature dependence and nonlinearity. In addition to the digital RS485 interface, the sensors also have a rangeable analog output.

With the EASYPRO CS, you get a configurable system. This customised solution is ideal for industrial applications and saves costs as only the required components are installed. The design of the base plate allows the CS120 to be used in combination with up to three other measured variables in the water. The integrated TOPAX® MC multi-channel controller continuously measures the water parameters and keeps them within the target range. It controls a large number of actuators and final control elements and is simple and intuitive to operate. Components of the EASYPRO CS (mounted on base plate): . Multi-channel controller TOPAX® MC . Measuring cells and measuring cell fittings . Sample water filter . Flow monitor . DFR 45 flow controller with temperature sensor and sample water tapping point . Inlet and outlet tap . Holder for buffer solutions and buffer solutions for adjusting the measuring cells . Multicoloured LEDs

The pressure transmitters of the 21C series with ratiometric 0,5...4,5V output combine chip-in-oil measuring cells with conventional electrical connections and pressure connections, making them ideal for industrial use. The transmitters are extremely resistant to environmental influences and deliver accurate measurement results over a temperature range of -40 °C to 125 °C.

The level sensors of the 46X-Ei series combine a ceramic measuring cell for very low measuring ranges on the mbar scale with microprocessor electronics for compensating for temperature dependence and nonlinearity. In addition to the digital RS485 interface, the sensors also have a rangeable analog output. Intrinsically safe – suitable for use in explosive atmospheres.

The high-pressure transmitters of the 7LHPC series use the chip-in-oil technology developed by KELLER, uniting a pressure measuring cell, digital temperature compensation and signal processing in a compact housing made of stainless steel or Inconel. The transmitters are extremely resistant to environmental influences and deliver compensated measurement results as an analog, ratiometric 0,5...4,5V output signal over a wide temperature range.

The high-pressure transmitters of the 6LHPC series use the chip-in-oil technology developed by KELLER, uniting a pressure measuring cell, digital temperature compensation and signal processing in a compact housing made of stainless steel or Inconel. The transmitters are extremely resistant to environmental influences and deliver compensated measurement results as an analog, ratiometric 0,5...4,5V output signal over a wide temperature range.

The pressure transmitters of the 8LC series use the chip-in-oil developed by KELLER, uniting a pressure measuring cell, digital temperature compensation and signal processing in a compact housing made of stainless steel or Hastelloy. The transmitters are extremely resistant to environmental influences and deliver compensated measurement results as an analog, ratiometric 0,5...4,5V output signal over a wide temperature range.

The pressure transmitters of the 7LC series use the chip-in-oil developed by KELLER, uniting a pressure measuring cell, digital temperature compensation and signal processing in a compact housing made of stainless steel or Hastelloy. The transmitters are extremely resistant to environmental influences and deliver compensated measurement results as an analog, ratiometric 0,5...4,5V output signal over a wide temperature range.

The pressure transmitters of the 4LC series use the chip-in-oil developed by KELLER, uniting a pressure measuring cell, digital temperature compensation and signal processing in a compact housing made of stainless steel or Hastelloy. The transmitters are extremely resistant to environmental influences and deliver compensated measurement results as an analog, ratiometric 0,5...4,5V output signal over a wide temperature range.

FTIR analyzer in a turnkey cabinet for the measurement of up to 50 parameters, to be selected according to the application. MCERTs certified. Based on the FTIR technology (Fourier Transform Infrared) for simultaneous measurement of HCl, HF, NH3, NO, NO2, N2O, SO2, CO, CH4, TOC, H2O, CO2, O2, etc. • 180 °C heated sample line/measurement cell • turnkey system including industrial PC • measurement of trace concentrations in wet, corrosive gas streams • suited for hot wet measurement of soluble gases such as HCI, HF, NH3, etc.

NIR LED– Technology, Continuous InLine density measurement Description The HK8 Series are NIR (Near Infrared) LED InLine measurement devices with state–of–the–art technology. The devices are used on conveyor belt, in pipelines (connection via flowthrough measuring cell or flange) and in tanks / vessel. Through the modular construction (Sensor and evaluation unit are separate), the sensor can be installed at a difficult accessible places and the evaluation unit can be installed at a well accessible place. This ensure the easy handling. The modular construction makes the operation of the HK8– Series very easy.

NIR LED– Technology, Continuous InLine measurement of two organic components Description The HK3 Series are NIR (Near Infrared) LED InLine measurement devices with state–of–the–art technology. The devices are used on conveyor belt, in pipelines (connection via flow through measuring cell or flange) and in tanks / vessel. Through the modular construction (Sensor and evaluation unit are separate), the sensor can be installed at a different accessible places and the evaluation unit can be installed at a well accessible place. This ensure the easy handling. The modular construction makes the operation of the HK3– Series very easy.