Results for
NORELEM FRANCE
France
Aluminium. Rim flanges, steel. Version Aluminium bright. Steel electro zincplated. Note Standard T profile acc. to DIN 7721 T2 with metric pitch (trapezoidal toothing). At least one belt pulley must have a rim flange. The toothed belt pulleys have a centre bore or a pilot hole (this can vary due to manufacturing methods). For this reason, the dimension D2 max. given in the table is the maximum diameter of the bore with which the toothed belt pulleys are supplied. This pilot/centre bore can be amended by the customer to produce a reamed bore, reamed bore with keyway or a tapped hole. Alternatively, customers can also use bushes to reduce the bore diameter.
Request for a quoteNORELEM FRANCE
France
Standard HTD profile with metric pitch (rounded toothing). At least one toothed belt pulley must have a rim flange. Conical hole for taper clamping bushes. The taper clamping bushes must be ordered separately and are available for various shaft diameters. Pulleys with a taper hole are statically balanced as per ISO 1940 grade G16.
Request for a quoteNORELEM FRANCE
France
Endless toothed belt with trapezoidal profile to DIN 7721 T1 with metric pitch. Ideal for drives with high belt flexibility. Permits smallest pulley diameters. The toothed belts are intended for drives where precision is a requirement, safety is important and the effects of chemicals are a concern. maintenancefree highpower transmission minimal belt extension accurate positioning and angles very good chemical resistance, especially to oils, greases and fuels extremely high abrasion resistance transmits power up to 30 kW reliable speed up to 10,000 rpm
Request for a quoteIGUS® GMBH
Germany
drylin® ZLW-0630 basic toothed belt axis, basic version, feed rate 54mm/rev, aluminium profile, surface: hard-anodised, neoprene toothed belt in black, guide carriage length 60mm, shaft end support made of aluminium, alignment of drive pin on the right, stepper motor with stranded wire. Configure drylin SHT linear modules individually here: https://igus.eu/ddx
Request for a quoteIGUS® GMBH
Germany
ZLN miniature toothed belt axis based on the low-profile guide system drylin® N. System width 40mm, installation height 28mm. Ready-to-install system with stepper motors or BLDC/DC motors. Configure drylin SHT linear modules individually here: https://igus.eu/ddx
Request for a quoteNORELEM FRANCE
France
Belt back and belt teeth CR. Tension cords Glascord. Tooth covering mesh polyamide. Note Endless toothed belts with an arched profile as per ISO 13050 with metric pitch. The rounded shape of the tooth contour provides a particularly high degree of safety against incorrect tooth interlocking, combined with a very rounded tooth mesh. Operating noise is significantly reduced by the rounded tooth mesh. The toothed belts are robust, economical and versatile. Belt speed vmax perm. 50 m/s Transmissible power up to 8.42 kW Permissible speed up to 14000 rpm Lownoise and lowmaintenance Very good chemical resistance, particularly against oils, greases and fuels Accurate positioning and angles
Request for a quoteROLLON GMBH
Germany
Telescopic actuator with a synchronized toothed belt system for effective linear movement and minimal overall dimensions. Horizontally mounted, it is mainly used to feed presses installed in series. It extends in both directions, feeding a press in one direction, closing, then feeding another in the other direction. The closed actuator does not occupy space in the two presses, making it possible to feed both with a single system. LOAD CAPACITY ACCORDING TO DYNAMICS Reported data must be verified according to the application. Please get in touch with our technical department for more information.
Request for a quoteROLLON GMBH
Germany
Telescopic actuator with a synchronized toothed belt system for effective linear movement and minimal overall dimensions. The wall-mounted system feeds the machine and retracts, facilitating the feeding of machine tools where obstructions to protective doors must be avoided. LOAD CAPACITY ACCORDING TO DYNAMICS Reported data must be verified according to the application. Please get in touch with our technical department for more information.
Request for a quoteROLLON GMBH
Germany
Telescopic actuator with a synchronized toothed belt system for effective linear movement and minimal overall dimensions. The compactness of the closed system makes it ideal for environments without much space between the machine and the ceiling. LOAD CAPACITY ACCORDING TO DYNAMICS Reported data must be verified according to the application. Please get in touch with our technical department for more information.
Request for a quoteROLLON GMBH
Germany
Modline linear modules are toothed belt or ball screw driven systems with high accuracy, speeds and load performances. Our experience in the fields of the automotive plants, painting, plate working, manufacturing machines and palletization systems has allowed us to widen our product range with the most advanced technical solutions. Our products stand out for their: high quality and competitive performances; up to 12-m beams (longer lengths can be obtained with jointed versions), high level torsional rigidity, precise shape; no play transmissions achieved by high torque couplings; beams with transversal stiffening ribs and preset for threads on profile ends; accurate scaling and consequent reduced maintenance; fast and accurate belt or without play screw drives; the most complete range of accessories. The Modline linear module strong points are: toothed belt or ball screw driven linear modules; rolling on trapezoidal or recirculating ball guides; payloads from 3 to 2000 Kg; up to...
Request for a quoteIGUS® GMBH
Germany
Lead-free - According to (RoHS) 2002/95/EG Standards and Certificates drylin® trapezoidal lead screw nut - cylindrical nuts with right-hand thread Trapezoidal lead screw nuts made from lubricant-free iglidur® W300, J, J350 and A180. drylin® - trapezoidal leadscrew nuts - WSRM, JSRM, J350SRM and A180SRM drylin® trapezoidal lead screw nut - cylindrical nuts with left-hand thread Trapezoidal leadscrew nuts made from lubrication-free iglidur® W300 and iglidur® J. drylin® - trapezoidal leadscrew nuts - WSLM and JSLM drylin® trapezoidal lead screw nut - flanged nuts with right-hand thread Trapezoidal lead screw nuts made from lubricant-free iglidur® W300, J, J350 and A180. drylin® - trapezoidal leadscrew nuts - WFRM, JFRM, J350FRM and A180FRM drylin® trapezoidal lead screw nut - flanged nuts with left-hand thread Trapezoidal leadscrew nuts made from lubrication-free iglidur® W300 and iglidur® J. drylin® - trapezoidal leadscrew nuts - WFLM and JFLM drylin® Anti-backlash nuts Trapezoidal leadscrew nuts with reduced bearing clearance. Anti-backlash nuts drylin® split lead screw nuts Split lead screw nuts for easy assembly. drylin® split lead screw nut drylin® leadscrew nut - two start two-start lead screws, double stroke in addition to the usual trapezoidal leadscrew nuts. drylin® two-start leadscrew nut drylin® miniature nuts Screw drives ,iniatur lead screw nuts, small sizes. Miniature nuts small sizes drylin® lead screw nuts with spanner flat Ideal transmission of the torque through form fit. drylin® lead screw nuts with spanner flat drylin® disc drylin® disc – eliminate clearance easily at low cost drylin® disc drylin® - Trapezoidal threaded spindle drylin® - Trapezoidal threaded spindle drylin® - trapezoidal lead screws made from aluminum, coated drylin® - Trapezoidal threaded spindle, Aluminium drylin® - Trapezoidal lead screw spindles with pin drylin® - Trapezoidal threaded spindle with pin drylin® - Trapezoidal lead screw spindles reverse Increased flexibility for format adjustments: counter rotating drylin® lead screws. reverse drylin® Zero backlash screw drives Screw drives with steep thread for quick adjustments. Zero backlash screw drives drylin® steep-threaded nuts For quick adjustments as an alternative to pneumatic or toothed belt. Leadscrews drylin® steep thread DST Lubricant-free steep thread DST higher performance in service life and efficiency Steep thread DST drylin® steep-threaded spindles Lubrication-free threaded spindles with high pitches. Steep-threaded spindles drylin® leadscrew nuts made of SHT linear modules Threaded nuts made of SHT linear modules drylin® leadscrew nuts made of SHT linear modules drylin® leadscrew nuts made of SLW linear modules Threaded nuts made of SLW linear modules drylin® leadscrew nuts made of SLW linear modules drylin® leadscrewsstorage Anodized aluminum bearing blocks of iglidur® L250. Design your own linear table. Leadscrewsstorage Floating bearing block for lead screws with ball bearing Useful extension to the drylin® construction kit. Floating bearing block for lead screws with ball bearing drylin® lead screw nut retainer Conveniently use srews to standard lead screw nuts with nut retainers drylin® lead screw nut retainer drylin® spherical trapezoidal lead screw nut To compensate for angular errors in screwed on plates. Spherical trapezoidal lead screw nut drylin® spherical lead screw nut with flange housing spherical trapezoidal lead screw nut, which permits continuous angle adjustments. drylin® leadscre nut with flange housing drylin® spherical lead screw nut with pillow block bearing Spherical lead screw nut with pillow block bearing continuous angle adjustments. drylin® lead screw nut with pillow block bearings drylin® quick-release nut – Fast Forward Fast forward mechanism: A combination of accurate positioning and quick manual adjustment with trapezoidal lead screw nuts. Quick release mechanism drylin® clamping rings drylin® clamping rings - flexible even down to the finest of details, made of coated aluminum. drylin® clamping rings drylin® trapezoidal lead screw nut - cylindrical nuts with right-hand thread Trapezoidal lead screw nuts made from lubricant-free iglidur® W300, J, J350 and A180. drylin® - trapezoidal leadscrew nuts - WSRM, JSRM, J350SRM and A180SRM drylin® trapezoidal lead screw nut - cylindrical nuts with left-hand thread Trapezoidal leadscrew nuts made from lubrication-free iglidur® W300 and iglidur® J. drylin® - trapezoidal leadscrew nuts - WSLM and JSLM drylin® trapezoidal lead screw nut - flanged nuts with right-hand thread Trapezoidal lead screw nuts made from lubricant-free iglidur® W300, J, J350 and A180. drylin® - trapezoidal leadscrew nuts - WFRM, JFRM, J350FRM and A180FRM drylin® trapezoidal lead screw nut - flanged nuts with left-hand thread Trapezoidal leadscrew nuts made from lubrication-free iglidur® W300 and iglidur® J. drylin® - trapezoidal leadscrew nuts - WFLM and JFLM drylin® Anti-backlash nuts Trapezoidal leadscrew nuts with reduced bearing clearance. Anti-backlash nuts drylin® split lead screw nuts Split lead screw nuts for easy assembly. drylin® split lead screw nut drylin® leadscrew nut - two start two-start lead screws, double stroke in addition to the usual trapezoidal leadscrew nuts. drylin® two-start leadscrew nut drylin® miniature nuts Screw drives ,iniatur lead screw nuts, small sizes. Miniature nuts small sizes drylin® lead screw nuts with spanner flat Ideal transmission of the torque through form fit. drylin® lead screw nuts with spanner flat drylin® disc drylin® disc – eliminate clearance easily at low cost drylin® disc drylin® - Trapezoidal threaded spindle drylin® - Trapezoidal threaded spindle drylin® - trapezoidal lead screws made from aluminum, coated drylin® - Trapezoidal threaded spindle, Aluminium drylin® - Trapezoidal lead screw spindles with pin drylin® - Trapezoidal threaded spindle with pin drylin® - Trapezoidal lead screw spindles reverse Increased flexibility for format adjustments: counter rotating drylin® lead screws. reverse drylin® Zero backlash screw drives Screw drives with steep thread for quick adjustments. Zero backlash screw drives drylin® steep-threaded nuts For quick adjustments as an alternative to pneumatic or toothed belt. Leadscrews drylin® steep thread DST Lubricant-free steep thread DST higher performance in service life and efficiency Steep thread DST drylin® steep-threaded spindles Lubrication-free threaded spindles with high pitches. Steep-threaded spindles drylin® leadscrew nuts made of SHT linear modules Threaded nuts made of SHT linear modules drylin® leadscrew nuts made of SHT linear modules drylin® leadscrew nuts made of SLW linear modules Threaded nuts made of SLW linear modules drylin® leadscrew nuts made of SLW linear modules drylin® leadscrewsstorage Anodized aluminum bearing blocks of iglidur® L250. Design your own linear table. Leadscrewsstorage Floating bearing block for lead screws with ball bearing Useful extension to the drylin® construction kit. Floating bearing block for lead screws with ball bearing drylin® lead screw nut retainer Conveniently use srews to standard lead screw nuts with nut retainers drylin® lead screw nut retainer drylin® spherical trapezoidal lead screw nut To compensate for angular errors in screwed on plates. Spherical trapezoidal lead screw nut drylin® spherical lead screw nut with flange housing spherical trapezoidal lead screw nut, which permits continuous angle adjustments. drylin® leadscre nut with flange housing drylin® spherical lead screw nut with pillow block bearing Spherical lead screw nut with pillow block bearing continuous angle adjustments. drylin® lead screw nut with pillow block bearings drylin® quick-release nut – Fast Forward Fast forward mechanism: A combination of accurate positioning and quick manual adjustment with trapezoidal lead screw nuts. Quick release mechanism drylin® clamping rings drylin® clamping rings - flexible even down to the finest of details, made of coated aluminum. drylin® clamping rings Lead-free - According to (RoHS) 2002/95/EG Standards and Certificates
Request for a quoteIGUS® GMBH
Germany
drylin® W - Advantages Dirt-resistant Weight saving Lubrication-free High speed Silent and light weight drylin® W - Advantages drylin® W - technical properties The technical properties of the drylin® W profile guide system Technical properties drylin® W - configuration Find the right profile guide system in 4 simple steps with the system and life calculation. drylin® W - configuration Single rail and housing bearing - round Sizes: 10 mm, 16 mm, 20 mm and 25 mm DryLin® W single rail and housing bearing - round Single rail and housing bearing - angular Sizes: 6 mm, 10 mm, 16 mm and 20 mm DryLin® W single rail and housing bearing - angular double rail, round Sizes: 10 mm (rail width 40 mm, 74 mm and 120 mm), 16 mm (rail width 58 mm), 20 mm (rail width 82 mm) and 25 mm (rail width 120 mm) DryLin® W double rail Guide carriage, assembled Sizes: 10 mm, 16 mm, 20 mm and 25 mm DryLin® W guide carriage, assembled double rail, square Sizes: 06 mm (rail width 30 mm), 10 mm (rail width 40 mm and 74 mm) and 16 mm (rail width 58 mm) drylin® W double rail, square Mono-slide guide carriage Size: 10 mm Mono-Slide guide Single rail and housing bearing - round, adjustable Sizes: 10 mm, 16 mm and 20 mm Linear Guides with “Turn-To-Fit” Hybrid bearing WJRM drylin® roller bearings - Roll and glide for easy movement. drylin® W hybrid bearing | roller bearing hybrid bearing double WJRM drylin® double roller bearing - Roll and glide for easy movement. drylin® W hybrid bearing double Double rail, reduced weight Sizes: 6 mm (rail width 30 mm), 10 mm (rail width 40 mm and 80 mm) DryLin® W double rail, reduced weight Hybrid carriage with rollers Size: 10, 16 mm DryLin® W hybrid carriage with rollers Stainless steel guide V4A, individual Size: 20 mm DryLin® W stainless steel guide V4A - individual Stainless steel guide V4A - double DryLin® W stainless steel guide V4A - double drylin® W slider rails/carriages drylin® W rail profiles with 3/8" threads, complete rails with Ø 10 mm through bore, with/without hand clamps DryLin® W double rail, square Gliding elements For round and angular rails. DryLin® W - Gliding elements Manual clamp Developed for simple positioning tasks. DryLin® W - Manual clamp Digital measuring system With immediate digital indication of position. DryLin® W - Digital measuring system Hand clamp for higher forces Designed for positioning tasks with higher forces. DryLin® W hand clamp for higher forces DryLin® WKMEX digital measuring system with external output drylin® WKMEX measuring system with external output DryLin® SLW - the compact* Spindle-lift tables The extremely thin unit is based on a DryLin® W profile system, and its entire length is supported. This design offers an extremely high torsional stiffening simultaneously with compact dimensions. DryLin® SLW - Compact DryLin® ZLW Toothed belt axis For quick positioning of small loads. DryLin® ZLW - Toothed belt axis Single rail and housing bearing - round Sizes: 10 mm, 16 mm, 20 mm and 25 mm DryLin® W single rail and housing bearing - round Single rail and housing bearing - angular Sizes: 6 mm, 10 mm, 16 mm and 20 mm DryLin® W single rail and housing bearing - angular double rail, round Sizes: 10 mm (rail width 40 mm, 74 mm and 120 mm), 16 mm (rail width 58 mm), 20 mm (rail width 82 mm) and 25 mm (rail width 120 mm) DryLin® W double rail Guide carriage, assembled Sizes: 10 mm, 16 mm, 20 mm and 25 mm DryLin® W guide carriage, assembled double rail, square Sizes: 06 mm (rail width 30 mm), 10 mm (rail width 40 mm and 74 mm) and 16 mm (rail width 58 mm) drylin® W double rail, square Mono-slide guide carriage Size: 10 mm Mono-Slide guide Single rail and housing bearing - round, adjustable Sizes: 10 mm, 16 mm and 20 mm Linear Guides with “Turn-To-Fit” Hybrid bearing WJRM drylin® roller bearings - Roll and glide for easy movement. drylin® W hybrid bearing | roller bearing hybrid bearing double WJRM drylin® double roller bearing - Roll and glide for easy movement. drylin® W hybrid bearing double Double rail, reduced weight Sizes: 6 mm (rail width 30 mm), 10 mm (rail width 40 mm and 80 mm) DryLin® W double rail, reduced weight Hybrid carriage with rollers Size: 10, 16 mm DryLin® W hybrid carriage with rollers Stainless steel guide V4A, individual Size: 20 mm DryLin® W stainless steel guide V4A - individual Stainless steel guide V4A - double DryLin® W stainless steel guide V4A - double drylin® W slider rails/carriages drylin® W rail profiles with 3/8" threads, complete rails with Ø 10 mm through bore, with/without hand clamps DryLin® W double rail, square Gliding elements For round and angular rails. DryLin® W - Gliding elements Manual clamp Developed for simple positioning tasks. DryLin® W - Manual clamp Digital measuring system With immediate digital indication of position. DryLin® W - Digital measuring system Hand clamp for higher forces Designed for positioning tasks with higher forces. DryLin® W hand clamp for higher forces DryLin® WKMEX digital measuring system with external output drylin® WKMEX measuring system with external output DryLin® SLW - the compact* Spindle-lift tables The extremely thin unit is based on a DryLin® W profile system, and its entire length is supported. This design offers an extremely high torsional stiffening simultaneously with compact dimensions. DryLin® SLW - Compact DryLin® ZLW Toothed belt axis For quick positioning of small loads. DryLin® ZLW - Toothed belt axis drylin® W - Advantages Dirt-resistant Weight saving Lubrication-free High speed Silent and light weight drylin® W - Advantages drylin® W - technical properties The technical properties of the drylin® W profile guide system Technical properties drylin® W - configuration Find the right profile guide system in 4 simple steps with the system and life calculation. drylin® W - configuration
Request for a quoteKEIPER GMBH & CO. KG ANTRIEBS- U. TRANSPORTTECHNIK
Germany
KEIPER synchronizing toothed shafts can be made of such diff erent materials as aluminum, steel or stainless steel. The fact that they can be produced with all pitches and designed according to your specifications and drawing ensures optimal solutions for all applications and any loads. Our synchronizing toothed shafts work together optimally with our extensive and complete range of timing belts. Together they are a perfectly matched system for your application. We have a large range of standard pulleys on stock, which can be reworked according to your specifi cations within a short time (e.g. bores and machining based on your drawings). Special surface coatings, e.g. such as hard coating, anodizing, zinc coating or bronzing, improve corrosion and wear resistance.
Request for a quoteFRANKE GMBH
Germany
Bearing assemblies with direct drive are suitable for applications where high performance and low space requirements are important criteria. The integration of the drive into the bearing housing means that wear-prone assemblies for transmitting drive power, such as toothed belts, shafts or chains, can be dispensed with. This reduces the required drive energy and also benefits more accurate positioning.
Request for a quoteKULLEN-KOTI GMBH
Germany
Toothed belt brushes from Kullen complement the belt brush range and offer one advantage in the feeding technique which the others do not: they can be set to a measurable cycle time. We only use standard toothed belts made of polyurethane with especially welded studs for fixing the fill material. The toothed belts are resistant against humidity, oils, greases and most chemicals. They can be used at temperatures between -15°C up to 80°C. Our experience shows that the required variations of toothed belt brushes are specific according to the customer's application and thus are normally produced ready to be installed as an endless unit. This brush type is available in common widths (KB) of standard toothed belts divided in T5, T10 and T20. The belt length depends on your requirements. You should always inform us about the inside belt length. The maximum belt speed is 6 m/s. Mainly natural hairs and bristles, plant fibres and synthetic bristles (PP, PA, etc.) are used, so all kinds of...
Request for a quoteNORELEM FRANCE
France
Body, extruded aluminium section. Bearing housing and slide, aluminium. Profile guide rail and guide carriage, steel. Toothed belt, polyurethane with steel cord reinforcement. Version Body natural colour anodised Bearing housing and slide, black anodised. Tracks of the profile guide rail, inductively hardened and ground. Note Compact and flexible linear actuators with toothed belt drive. The body consists of a selfsupporting aluminium extruded section with integrated profile guide rail. This rail system is able to absorb highest forces from all directions, is lowwear, and is optimised for moving large masses. Slots are located on the outer sides of the aluminium profile, ensuring easy, reliable assembly and enabling accessories mounted. Proximity switches can be positioned and fastened in the upper Tslot. The aluminium profile is fully compatible with our standard I series profiles.
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
NORELEM FRANCE
France
Steel. Toothed pulleys without aluminium rim flanges. Version Steel phosphated. Aluminium bright. Note Standard HTD profile with metric pitch (halfround toothing). At least one belt pulley must have a rim flange. The toothed belt pulleys have a centre bore or a pilot hole (this can vary due to manufacturing methods). For this reason, the dimension D2 max. given in the table is the maximum diameter of the bore with which the toothed belt pulleys are supplied. This pilot/centre bore can be amended by the customer to produce a reamed bore, reamed bore with keyway or a tapped hole. Alternatively, customers can also use bushes to reduce the bore diameter. The pulleys may be recessed on the sides.
Request for a quoteNORELEM FRANCE
France
The tension meter is used to perform a pretension test on commercially available belt systems quickly and easily by means of frequency measurement. Fully electronic and equipped with stateoftheart microprocessor technology, the meter enables precise adjustment of all V, toothed and flat belts that have to be tensioned in the range from 10 to 600 Hz. The measurement must never be performed while the drive is running The meter is not permitted or certified for use in potentially explosive areas.
Request for a quoteKEIPER GMBH & CO. KG ANTRIEBS- U. TRANSPORTTECHNIK
Germany
easy drive® track timing belts can be made from the complete range of polyurethane and neoprene timing belts: in open lengths, endless welded, for form belts, endless Flex or wide timing belts, in almost any length and width. The directional guiding, with groove in tooth, is either already integrated in the timing belt during production or added later. These timing belts exhibit the same properties as standard timing belts. However, in addition, axial movement is prevented and the zero-play guiding leads to high directional stability. Advantages • Universal application instead of flanged pulleys or special toothed belt guides • Can be used with any tooth shape or belt pitch • Can be combined with any material – steel, aluminium, grey cast-iron or plastics • For polyurethane and also for neoprene timing belts • Maximum directional stability, without lateral play, inaccurate running or drift
Request for a quotePRESSTA EISELE GMBH
Germany
Tooth belt drive with profile slide Available for following automatic cutting machines: Profilma 200, 250, 500E, 510E, 600R Max. load 750 KG Dimension of stories fix, e.g. max. cutting range of the saw Conveying length 1.850 mm Profile length from 2.700 – 10.000 mm Pneumatic gripper for good feeding of the profiles
Request for a quoteFRANKE GMBH
Germany
Franke linear modules type FTD are light, compact and ready-to-install positioning units. They are extremely compact and combine the guide system and toothed belt drive within the housing. Franke FTD linear modules can be used universally. They are suitable for long stroke lengths of up to 7 meters.
Request for a quoteFRANKE GMBH
Germany
Franke FTC linear modules are light, compact and ready-to-install positioning units. The external guide system is moved by an internal spindle or toothed belt drive. Franke FTC linear modules are very versatile. The guide cassette can be designed to meet customer specific requirements.
Request for a quoteFRANKE GMBH
Germany
Franke bearing assemblies type LVE are bearing assemblies with toothed belt gearing, aluminium housing rings and integrated bearing elements. Franke bearing assemblies type LVE are suitable for medium rotational speeds and accuracies. They convince by their low weight and are available at short notice, in some cases even from stock. Designed as 4-point bearings, they can support equally high loads from all directions and are insensitive to shocks and vibrations. The bearing assemblies are sealed on both sides and adjusted to preload.
Request for a quoteTECNORULLI S.R.L. CON SOCIO UNICO
Italy
PVC-STEEL cylindrical and tapered rollers with one or two grooves rolled on the steel tube, driven by round belt links in series or individually connected to a transmission bar activated by the motor unit. PVC and PVC-STEEL rollers with flat or toothed polyamide resin PA or steel ACC pulley driven by tangential belt or belt links in series. The diagrams and tables on page 86 show the dimensional characteristics and minimum and maximum lengths of manufacture. The rollers for flat or toothed belts are produced in the following versions: with pinion integral to the jacket for continuous transport; with friction pulley for stockpiling transport and in the connection of machines operating at different speeds.
Request for a quoteB+B AUTOMATIONS- UND STEUERUNGSTECHNIK GMBH
Germany
The products are manually placed on the conveyor belt, printed from above and collected at the end of the system. The portable system is equipped with a Wolke m610 Touch thermal inkjet system. An upgrade to a manual serialisation system with b+b Linemanager and Full Vision System is optionally available. The conveyor belt is driven by a powerful stepper motor with constant speed. The conveyor belts are provided with crossbars at regular intervals to achieve constant product guidance and thus a consistent print result. The distance between the two toothed belt conveyors can be easily adjusted in order to process different product widths. For processing slightly slanted products, the positions of the crossbars can also be adjusted to each other.
Request for a quoteIAI INDUSTRIEROBOTER GMBH
Germany
Toothed belt linear actuators from IAI are particularly suitable for high speeds, rapid accelerations and strokes between 200 mm and 3,200 mm. All actuators have a compact frame geometry and optimised cross section for maximum rigidity and load bearing capacity, making them resistant to twisting and deformation. IAI linear actuators with toothed belt drive are ideal for fast handling and positioning tasks in which high repeat accuracy with short cycle times are vital. The double slider option of the IF and the new IFA series gives the possibility to vary the distance between the two sliders. This increases the overhang load capability and allows a wide variety of configurations. Advantages at a glance ▸ High speed and acceleration ▸ High bending stiffness ▸ Long strokes ▸ Low maintenance ▸ Low noise
Request for a quoteIAI INDUSTRIEROBOTER GMBH
Germany
Electric linear actuators from IAI are available as rod, slider and slide table types as well as with toothed belt drive. They are equipped with a stepper motor or servo motor and often already have a battery-free absolute encoder as standard. On request, they can also be supplied without an electric drive unit. The product range of linear actuators consists of the RoboCylinder series, which are characterised by high user-friendliness, simple programming as well as compact design. Their focus is on covering common customer requirements and are therefore relatively inexpensive. Electric slider type actuators and axes with toothed belt drive from the IntelligentActuators product line complete the product portfolio. They meet higher requirements than RoboCylinders in terms of payload, speed, acceleration and precision.
Request for a quoteJERKO-SPRÜHSYSTEME GMBH
Germany
Jerko High Speed Manipulators are designed for extremely rough environmental conditions. Due to their encapsulated design, the ingress of dirt is impossible, while at the same time high loads up to 300kg can be handled. Driven by a powerful servo motor and a low-maintenance toothed belt drive, extreme accelerations up to 15m/s² are possible. Due to this simple and ingenious design, the manipulator can be integrated in all forging lines. Different spraying tools are possible to meet every task The manipulators can be modularly equipped with several independent axes. This design saves money and increases the productivity of your forging line! Many optional extras can be configured to meet all requirements.
Request for a quoteResults for
Toothed belts - Import exportNumber of results
40 ProductsCompany type
Category