Tank design - Import export

Floor box 8808B made of stainless steel. Inside there are two aluminum equipment racks for 4 units each. It can be installed at any point in the floor, as pipes are used for the line feed. Because of its low height, this version is particularly suitable for floors in old buildings. The rimless lid also closes when the plugs are inserted and is designed for sticking on floor coverings. Further equipment variants on request.

Slow speed aerators used for aeration and mixing of urban and industrial wastewater in various processes Provided in either fixed bridge or floating designs Ideal for Aerating most types of wastewater or industrial euents The TLF® Turbine Aerator is one of the most ecient aeration products in the marketplace Produces High Mixing and Homogenous Solutions in large lagoons and ASP tanks. IP55 geared motor with IE3 highly efficient rating Coupling sleeve and based materials coated with high grade Epoxy Paint Float can me supplied in various materials including HDPE Rotor made of glass fibre reinforced polyester. The GRP has a low density which allows installation without having to empty the tank and the design also reduces the axial loads on the gearbox.

Storage tanks used in the production and processing of corrosive fluids must meet customer safety requirements as well as the standards and regulations in force in the country of delivery. CTRA offers a wide range of solutions for these storage tanks. These can be built entirely in GRP or in GRP - Thermoplastic composites depending on the nature of the stored product. Our tanks cover a range from 0.5m to 6m in diameter and from 0.5 m3 to 300 m3. Other volumes can be designed and built on request.

The transport of corrosive fluids by road, rail and water is highly regulated. Design and quality requirements are very high because these hazardous materials are transported on public roads. CTRA offers a range of solutions for these tank containers, which can be made of GRP / GRP Thermoplastic or GRP Thermoplastic.

TAILOR MADE SOLUTIONS As a family owned company that offers a unique tank storage system to customers across the world, Lipp knows the high value of effective communication and customer support. Whether consulting with a Lipp specialist on a tank system design or ordering extra accessories for an installed system, the same professional help and guidance is always available. Lipp focuses on providing the optimum solution for the user, entirely customisable and ultimately efficient. Lipp will always recommend solutions that will increase the performance of a tank system while also ensuring – that it is the most suitable solution for the customer.

WITH DIGESTER CHAMBER VOLUMES RANGING FROM 200 M3 TO 5.000 M3 The LIPP Universal digester which unlike the KomBio reactor does not have an integrated gas accumulator, is used for larger plants for industry and municipalities. The biogas accumulated is either directed into a KomBio reactor combined with the Universal digester or into a separate gas accumulator. KEY BENEFITS Production of renewable energy and reduction of fossil CO2 emissions Low noise emissions Flexible substrate composition Customisable pumping and stirring technology High functional safety Effective insulation results in low heating requirement Quick construction thanks to on site production Low investment costs Low maintenance and durable Consistent quality worldwide PRODUCT SPECIFICATION MODULAR PLANT CONCEPT The LIPP Universal digester essentially consists of a (Verinox) stainless steel tank with a modular design. Panel heating and insulation are fitted on the outside and are easily accessible.

FOR THE INTERMEDIATE STORAGE OF RENEWABLE ENERGIES – FROM 200 TO 2,000 M³ The LIPP® thermal storage tank is the tailored thermal storage solution for renewable energies with an effective volume ranging from 200 to 2,000 m3 which is suitable for individual customisation. Expedient thermal storage is a prerequisite for the effective utilisation of heat from biogas plants, biomass cogeneration plants, solar plants or other heat sources. The flexible capacity LIPP® buffer storage tank provides the ideal solution for this application. The tanks are fabricated on site using the tried and tested LIPP® Double Seam System and the stainless steel VERINOX®. Insulation can be tailored to the intended application in order to produce large volume, above ground storage tanks with an individually customised interior. The tanks are designed for non pressurised operation with an operating temperature of up to 95 °C and are suitable for use with heating water. No additional nitrogen system necessary.

Round CEE floor tank 7705A in heavy design with housing and screw lid made of solid PVC and a device carrier made of aluminum. The lid is made of aluminum and can be locked with a special key. When closed, the CEE 7705A floor tank is waterproof. Degree of protection IP 67. Further configurations on request.

Load cell capacity range from 30 kg to 300 kg. Specially designed for tank and hopper weighing as well as basic dosing systems. For use in EX zones 1, 2, 20, 21, 22 and FM DIV 1. Compact design ensuring a low system height Accuracy class: 0.05 % Extreme wide temperature range Corresponding mounting kits

Specially designed for tank and hopper weighing, hybrid scales and high-precision dosing systems. For use in EX zones 1, 2, 20, 21, 22 and FM DIV 1. Ultra-high precision load cell for batching applications Load cell capacity range from 100 kg to 3 t Accuracy class: D1 (0.04 %), C3 (0.015 %), C6 (0.008 %) Corresponding mounting kit: PR 6046

Compression load cells from 100 kg to 5 t. Specially designed for tank and hopper weighing as well as basic dosing systems. For use in EX zones 1, 2, 20, 21, 22 and FM DIV 1. Ultra-high precision load cell for batching applications Load cell capacity range from 100 kg to 5 t Accuracy class: 0.04 % - 0.008 % Corresponding mounting kits

• Control cabinet with process control, inspection and monitoring for automated applications • Integrated control and safety components • Simple, ergonomic operation • For use with stationary CO2 tank (or bundles) • Modular construction, design according to customer requirements

Length: Approximately 20 feet (6.1 meters) Width: Standard ISO container width Height: Standard ISO container height"2. Material: Typically made of stainless steel to ensure resistance to corrosion and durability, which is crucial for transporting hazardous materials like refrigerants.**3. Capacity: The capacity of the ISO tank is designed to accommodate a specific volume of R40<Ja refrigerant based on its density and weight characteristics."t. Pressure Rating: The SO tank would oe designed to handle the pressure associated with storing and transporting R40£a refrigerant. The pressure rating would meet safety standards.'*5. Valves and Fittings: Equipped with appropriate

Storage and Transportation: ISO tanks provide a safe and secure means of storing and transporting refrigerant gases. These tanks are designed to handle the specific properties and pressures associated with refrigerants.2. Bulk Quantity Handling: SO tanks allow refrigerant gases to be transported and stored in large quantities, facilitating bulk distribution to meet the demands of various industries.3. Safety Features: ISO tanks for refrigerant gases are equipped with safety features to ensure proper handling and storage. This includes pressure relief valves, emergency vents, and other safety mechanisms to maintain the integrity of the tank and prevent accidents.4. Standardization ISO tanks adhere to international standards, ensuring uniformity in size, design, and handling procedures. This standardization alows for seamless intermodal transportation and handling across different regions.5. Efficient Loading and Unloading ISO tanks are designed for efficient

CR-M - Electric tote tank mixer for stainless steel IBCs The tote tank mixers CR-M are designed for operation on stainless steel containers with filling openings of DN 400 mm and mixing volumes from 400 l up to 1,500 l. Depending on the viscosity of the mixing material, CR-Ms with fast running or gear reduced drives are available. The agitator shafts are connected to the drive shafts with sleeve couplings or borne within the gear’s hollow shaft (worm gear). The agitator shafts are balanced for concentric run after assembly. The mixer is mounted on the container’s manway lid, which is clamped with butterfly screws or a clamp ring. The manway lid is supplied by the container manufacturer or by the customer. The impellers are designed to fit through the filling opening DN 400 when being inserted. The electric container mixers are delivered with on-/off-switches with low-voltage breaker. The electric container mixers can also be supplied with frequency converter drives. All CR-M...

CR-E - electric tote tank mixer for plastic IBCs The tote tank mixers CR-E are designed for operation on plastic containers with filling openings of 150 mm and volumes from 600 l up to 1,200 l. The customer may choose between various viscosity-related basic versions of fast-running and slow-running mixers with electric drives. The agitator shafts are connected to the drive shafts with sleeve couplings or borne within the gear’s hollow shaft (worm gears). The agitator shafts are balanced for concentric run after assembly. CR-E 6 0,75 The mixer is mounted on a container traverse bridge, which is included in the scope of supply and clamped with a rapid fixing system to the cage frame of the IBC. The plastic bulk of the container is therefore not harmed by any static or dynamic loads by the agitator. The fixing of the traverse bridge is adjustable for various container models. The impellers are designed to fit through the filling opening 150 mm when being inserted. The electric...

NRK - Compact top-entry agitator The NRK series is a compact top-entry agitator that can be used to meet high requirements regarding both surfaces and cleaning inside and outside of the tank. Due to its’ compact design, agitator shafts with diameters of 25 mm and lengths of up to 1,200 mm can be realized, making the NRK the ideal mixer for small tanks in food and drug industry. GMP and FDA conform design. The NRK series agitator has an integrated bearing and coupling housing with flexible coupling to connect drives with shaft journals. The NRK can be supplied with radial shaft seal rings for non-pressurized operation or with liquid-lubricated mechanical seals on pressurized tanks. Explosion protection to ATEX 2014/34/EU for explosive zones 0 to 2 for gases and for explosive zones 20-22 for dusts (device group II, categories 1-3).

The tote tank mixers CR-M are designed for operation on stainless steel containers with filling openings of DN 400 mm and mixing volumes from 400 l up to 1,500 l. Depending on the viscosity of the mixing material, CR-Ms with fast running or gear reduced drives are available. The agitator shafts are connected to the drive shafts with sleeve couplings or borne within the gear’s hollow shaft (worm gear). The agitator shafts are balanced for concentric run after assembly. The mixer is mounted on the container’s manway lid, which is clamped with butterfly screws or a clamp ring. The manway lid is supplied by the container manufacturer or by the customer. The impellers are designed to fit through the filling opening DN 400 when being inserted. The electric container mixers are delivered with on-/off-switches with low-voltage breaker. The electric container mixers can also be supplied with frequency converter drives. All CR-M series mixers can be supplied as follows:

The tote tank mixers CR-E are designed for operation on plastic containers with filling openings of 150 mm and volumes from 600 l up to 1,200 l. The customer may choose between various viscosity-related basic versions of fast-running and slow-running mixers with electric drives. The agitator shafts are connected to the drive shafts with sleeve couplings or borne within the gear’s hollow shaft (worm gears). The agitator shafts are balanced for concentric run after assembly. The mixer is mounted on a container traverse bridge, which is included in the scope of supply and clamped with a rapid fixing system to the cage frame of the IBC. The plastic bulk of the container is therefore not harmed by any static or dynamic loads by the agitator. The fixing of the traverse bridge is adjustable for various container models. The impellers are designed to fit through the filling opening 150 mm when being inserted. The electric container mixers are delivered with on-/off-switches with low-voltage breaker.

The NRK series is a compact top-entry agitator that can be used to meet high requirements regarding both surfaces and cleaning inside and outside of the tank. Due to its’ compact design, agitator shafts with diameters of 25 mm and lengths of up to 1,200 mm can be realized, making the NRK the ideal mixer for small tanks in food and drug industry. GMP and FDA conform design. The NRK series agitator has an integrated bearing and coupling housing with flexible coupling to connect drives with shaft journals. The NRK can be supplied with radial shaft seal rings for non-pressurized operation or with liquid-lubricated mechanical seals on pressurized tanks. Explosion protection to ATEX 2014/34/EU for explosive zones 0 to 2 for gases and for explosive zones 20-22 for dusts (device group II, categories 1-3).

Astra will help you choose the right storage tank design and size for storing your product at the desired temperature, staying homogeneous, without changing original product structure. 10 liters is the smallets tank was produced at "Astra" and a largest was distillation column of 500,000 liters. We are not afraid of oversized products, only two questions remain, is there a way to deliver it to your site and will the produced tank fit into your factory?

Agromeks - New Generation Moving Drum Jaguar Stone Collecting Machine is a superior agricultural equipment that has become an important player in the agricultural sector and maintains its leading position in transforming stony lands into productive agricultural areas. The most striking feature of this machine is its springless floating bearing drum system. This system makes it possible to easily collect stones from 3 cm to 50 cm, thanks to the up-down moving drum beds that can adapt to sudden load changes during operation. Larger warehouse volume increases efficiency by offering up to 9,000 kg stone storage capacity . It has an innovative design, embroidered tank plates and a three-layer hood system. Agromeks - New Generation Jaguar Stone Collecting Machine with Movable Drum is designed to process your soil while collecting stones from the surface to a depth of 30 cm on your land with a spring sieve and special drum system.

Agromeks - New Generation Moving Drum Jaguar Stone Collecting Machine is a superior agricultural equipment that has become an important player in the agricultural sector and maintains its leading position in transforming stony lands into productive agricultural areas. The most striking feature of this machine is its springless floating bearing drum system. This system makes it possible to easily collect stones from 3 cm to 50 cm, thanks to the up-down moving drum beds that can adapt to sudden load changes during operation. Larger warehouse volume increases efficiency by offering up to 9,000 kg stone storage capacity . Its innovative design has embroidered tank plates and a three-layer hood system. Agromeks - New Generation Jaguar Stone Collecting Machine with Movable Drum is designed to process your soil while collecting stones from the surface to a depth of 30 cm on your land with a spring sieve and special drum system.

The machine is designed for cleaning and degreasing of machine parts and components. The components placed in the rotating basket, which can have a diameter of 800, 1000 or 1200 mm. By rotating of the basket the components are washed with washing solution. The machine can be with or without insulation, sensors for level-and temperature controls, mud sump or oil separator. The mud sump is welded to the machine’s corpus. The washing solution flows from the tank into the mud sump and catches the gross dirt. The purified solution flows from the mud sump in the tank. The oil separator designed for separation of the oil from the washing solution. The oil is separated as a surface layer, which is collected in a special bath and discharged out of the chamber. The skimmed fluid is returned to the tank. Machine corpus made entirely out of stainless steel, material No. 1.4301. The machine complies with the high CE-Requirements and EU- a

950 tank cap female threaded, in plastic material, passage diameter 32 mm, with different types of sealing gasket in relation to the fluid in the tank. It is available hermetic, ventilated or ventilated through valves. For the optimal operation of the endothermic engine or in case it is required by law or specific regulations, the 950 tank cap can be equipped with unidirectional valves, that allow both the expulsion of vapors generated by fuel and the air inlet into the tank; moreover, in case of tank overturning, the loss of fuel is limited by the valves of controlled ventilation system. 950 fuel tank plug can be supplied in different colours on request. The trapezoidal threaded filler neck profile, compatible with 950 tank cap, is obtained directly from the tank molding. The ergonomic design makes the handle easier also when the worker uses his working gloves;

TIGHTChecker is an ultrasound solution designed to verify the tightness of closed volumes. Focused Tightness integrity is an issue that plagues every industry. TIGHTChecker is an ultrasound solution focused on pinpointing leaks in any volume. Cars, trains, airplanes, buildings, cleanrooms… TIGHTChecker checks them all. Simple TIGHTChecker is so easy to use. Simply open the box, position the T-SONIC1, seal the volume and listen for leaks. TIGHTChecker’s crystal-clear sound and vibrant colour display pinpoints even the smallest leaks. Affordable With so many things to test, TIGHTChecker is in high demand. It’s low entry cost, versatility, and SDT quality make it the most affordable solution for testing everything that leaks. And everything leaks. Use the TIGHTChecker to pinpoint the exact location of leaks in vehicles, buildings, tanks, and ships. Designed for use with SDT’s ergonomic Flexible sensor and compact T-Sonic1 transmitter.

Suction immersion pumps series TAS/STS make it possible to connect to vacuum filters through their simple connection on the suction side (for instance, with a slot screen). Suction immersion pumps without seals are positioned in the area of unfiltered coolant in the tank. With their robust design, they allow operating pressures of - 0.3 bar to - 0.5 bar on the suction side. Volumetric delivery: up to 1200 l/min Delivery head: up to 60 m The STS serie offers a flange with pressure gauge connection port. The flange can be rotated for either horizontal or vertical pipe connections. Please contact us for delivery quantity

A galvanised corrugated steel water tank is a robust container designed to efficiently store water. Water tanks provide a practical solution to address water supply challenges and find applications across a wide range of industries, including irrigation, fire suppression, agricultural farming, and more. Our water tanks are specifically engineered to meet the demands of water storage for irrigation, catering to a variety of crops such as olives, wheat, cotton, and more. With their durable construction and effective design, these tanks ensure a reliable and convenient solution for your irrigation needs. Please note that our galvanised corrugated steel tanks are not intended for drinking water purposes. Choose our galvanised corrugated steel tanks for their durability and performance, ensuring a dependable water storage solution for your agricultural and irrigation projects.

Horizontal Water Tanks & Bowsers These Horizontal Tanks & Bowsers are designed for the transportation of liquid such as water and liquid fertiliser. The tanks are designed to mount onto straight to flat surfaces with a unique pin mounting system without the need of mounting frames or steel mounting straps and are highly impact resistant and easy to fill. The horizontal plastic tanks are manufactured from WRAS approved polymer for the storage of drinking water (black, boat blue or natural coloured tanks only). These can be used as sprayer tanks or water bowsers for agricultural sprayers with a range of sprayer camlock fittings available to suit your sprayer. The optional Ball Baffle System guarantees fluid stability for safer operation, reducing fuel usage and mechanical wear & tear.