Results for
France
Rest pads are for supporting machined and non-machined parts. They can also be used as stops and thrust pads in fixtures and toolmaking. Studs or grub screws can be screwed and glued into the tapped hole D to make a rest pad with external thread.
Request for a quoteFrance
Hardened and ground. Top face without centerbore. Note: If more than one rest pad is used, the support height can be reground. Rest pads can also be used as feet for jigs and fixtures.
Request for a quoteFrance
Worm screw steel. Worm wheel CuZn37Mn3Al2PbSiS40. Version Worm screw with righthand pitch, casehardened HV 620 – 700, flanks and hole ground. Note for ordering Wheels/screws can only be combined to form a worm gear if they have the same centre distance and transmission ratio. Note A worm gear consists of a worm screw (shaft) and a worm wheel. Suitable for forming worm drives with a 90° shaft angle. A worm drive enables very large speed reduction ratios with a single stage. The toothing has the flank shape K. The engagement angle is 15°. The worm gears are prebored. The stated T2 output torques are the permissible output torques on the worm wheel. These apply for an input speed of 2800 rpm of the worm screw. The worm gears are suitable for continuous operation at high speeds and high torques. Attention 22500171002 Screw polished only. 22500172002 Worm wheel with helical gear toothing.
Request for a quoteFrance
The floating joint unit is a bolt for connecting two components, that permits a desired movement of those components in relation to each other. The floating joint unit is mainly used when: a temperature change alters the dimensions of a component assembly inaccuracies occur manufacturing tolerances must be compensated for the position of the components varies due to dynamic loads
Request for a quoteFrance
Slides steel. Ball cages steel. Balls, steel. Version Slides electro zincplated. Ball cages, electro zincplated. Balls hardened. Note for ordering Sold in pairs. Note By telescopic slides with full extension, the travel is roughly equal to the installed length, which ensures greater comfort and accessibility. The dynamic load capacity of the telescopic slides indicates the maximum load rating of a vertically mounted slide pair when the entire extension length is used. The load capacity specified is calculated with a slide spacing of 450 mm and is based on the maximum value with 80,000 cycles. Not suitable for horizontal mounting. The head height of the fastening screws should not exceed 1.8 mm otherwise there is a risk of collision with other parts of the slide. Advantages Low slide thickness Light running Precise guidance for high lateral stability
Request for a quoteFrance
Slides steel. Ball cages steel. Balls, steel. Version Slides electro zincplated. Ball cages, electro zincplated. Balls hardened. Note for ordering Sold in pairs. Note On telescopic slides with partial extension both sides, the travel is less than the installed length. Latches in open position on both sides. The dynamic load capacity of the telescopic slides indicates the maximum load rating of a vertically mounted slide pair when the entire extension length is used. The load capacity specified is calculated with a slide spacing of 450 mm and is based on the maximum value with 50,000 cycles. The load capacity is ca. 75% lower by horizontal mounting. The head height of the fastening screws should not exceed 2.5 mm otherwise there is a risk of collision with other parts of the slide. Advantages Pulls out in both directions Latches in open position on both sides Light running
Request for a quoteFrance
Polyethylene. Screw, steel. Note: Levelling feet with hexagonal base. Rigid version.
Request for a quoteAustria
Hot-dip galvanized mounting plate 2 stainless steel screws M16 x 32 mm Suitable for the hinges 4D16 and 4D20
Request for a quoteKazakhstan
Self-tapping screw for fastening, connecting sheet metal and metal profiles up to 0.9 mm Head: hexagonal with a shoulder, straight slot
Request for a quoteKazakhstan
Roofing self-tapping screw for metal DIN-EN-ISO 15480 (old - DIN 7504-K) with an EPDM washer 2.4-2.8 mm thick Standard Head: hexagonal with a shoulder, , turnkey 8 (D-5.5) or 10 (D-6.3) mm, a marking mark in the form of the letter "X" is stamped on the cap
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
Germany
Stainless steel barrel screw joint with a R 2" steel fine outer thread for tubes dia. 32 mm.
Request for a quoteChina
Custom Quality Stainless Steel Screws in low Price. Ming Xiao Metal Parts Manufacturing custom produce cold forging parts (such as bolt,nuts,screw,metal pin,meta stud) according to customer's drawing or sample, we made nonstandard fasteners by cold heading / cold forging or lathing - handle pins, Dowel Pins, nonstandard hex head bolts,squre head bolt,philips head screws,pan head screws, nonstandard screws, nonstandard pins, nonstandard nuts of square nuts,self lock nut,all kinds of metal studs,etc. Generally we use cold forging process to produce rough parts, then machining it again by turning,milling and other machining processes to make the parts with good surface and dimensions, this stainless steel screw is this type of machining process. This way can make the production cost reduced and the producing processes more less it's a more competitive way to produce high quantity parts.
Request for a quoteGermany
These screws are produced by automatic turining machine,custom screw fittings are mainly used in small internal parts of machinery.
Request for a quoteTurkey
Micron hand tools are made of high quality stainless steel material, allows you to install your curtain grommets easily. Remember to use a plastic mallet, not a steel hammer. Supplied with full instructions.
Request for a quoteTurkey
This 2 piece set is designed to work with the TEP 3, M 3, PL 10 and MC 20 fastener attaching machines. This dies set is made of stainless steel, for a durable and long lasting product.
Request for a quoteTurkey
With the added support provided by Grommet Mart’s Jean Rivets, your garments will perform and look their best. Jean rivets are offered in several basic styles that are attached using solid Metal Rivet Nails. All of our Jean Rivet combinations offer maximum attaching strength with high quality visual appearance. Jean rivets manufactured out of brass, designed to be installed in denim garments to securely fasten segments together.
Request for a quoteTurkey
With the added support provided by Grommet Mart’s Jean Rivets, your garments will perform and look their best. Jean rivets are offered in several basic styles that are attached using solid Metal Rivet Nails. All of our Jean Rivet combinations offer maximum attaching strength with high quality visual appearance. Jean rivets manufactured out of brass, designed to be installed in denim garments to securely fasten segments together.
Request for a quoteTurkey
With the added support provided by Grommet Mart’s Jean Rivets, your garments will perform and look their best. Jean rivets are offered in several basic styles that are attached using solid Metal Rivet Nails. All of our Jean Rivet combinations offer maximum attaching strength with high quality visual appearance. Jean rivets manufactured out of brass, designed to be installed in denim garments to securely fasten segments together.
Request for a quoteResults for
Steel screws - Import exportNumber of results
232 ProductsCountries
Company type
Category