Safety control system - Import export

The combination of crane control and wireless control concept creates the link between an operator and a crane and thus makes optimum load handling a tangible experience. Absolutely safe operation of a crane or a system of several cranes must always be guaranteed – safety for the crane operator as well as for the transported goods and surrounding infrastructure. The smart Demag SafeControl system enables independent and continuous monitoring of a crane on the basis of a largely redundant control concept to bring the system to a standstill independently if any irregularities occur. Furthermore, dangerous conditions can be identified and prevented in advance. The crane operator can concentrate fully on his/her work at all times thanks to the safety control system. A crane can be conveniently and intuitively controlled by radio, which is also very efficient. The safety control system combined with radio control can ensure gentle handling and precise positioning of loads.

Electrical control panel for starting and capacity control of : the compressor, the air dryer, the cooling water system with pump when supplied. Cabinet made of 2mm enamelled plate, protection to IP54 hermetically sealed and containing: Main circuit breaker and fuses. Star delta starter for compressor. Fuses for auxiliary circuits. Safety device to prevent compressor starting against load. Microprocessor description overview Capacity control with fully automatic start and time delayed stop of the compressor. Monitoring of air an oil temperatures on each stage, as well as oil and air pressures. Safety controls. Memorised defect system. Service intervals for maintenance. Details of loaded and total running hours. Simple keypad operation. Multi language message displays. RS485 data communication line for remote control or monitoring. Diagnostics, reprogram, Analog, digital configuration… new model available 2009 sept. Main Selection Monitoring Start control Pressure...

Kalopi pedicure spa for your client safety and to comply with regulations. All of spa bases installs pipeless magnetic jet in which water does not circulate outside of the tub. Suitable for liner. The impeller is designed stainless steel shaft for long life guarantee and never worry dry running. ​ Easy to opean luxurious chromed jet cover and clean whole system . ​​​​ The impeller housing has O ring that can make sure whirlpool water won't leaks from cap. DC24V brusless with safety control system that will turn off power if sink without enough water. The base can be installed either engineered stone or glass bowls that easy clean and maintain. ​ The K3 pedicure spa chairs come with a wide variety of features and design . Here are some of our important factors to consider for nail salons.

Heat treatment OPERATING TEMPERATURE: MAX 1200°C Standard power, size and shape or as indicated by the customer. Complete electrical BOXES with CONTROL and SAFETY systems (thermocouples). Stainless steel casing. Room insulation with technical material REFRACTORY and FIBROCERAMIC. Heating by resistive filament* SPIRAL. VIDEO: LINK

With its discrete design, Automatic Systems glass turnstile TBV 327 is intended for prestigious entrances. Its sober and modern Its sober and modern esthetics exerts a reduced impact on the architectural surroundings. It combines perfectly with the PPV 323 swing gate. Reliability & Performance Long lifecycle Reduced operating costs Flexibility Possibility of manual intervention by the operator Compatible with any access control system Safety Complete elimination of angles Central rotating column Free rotation in the event of an emergency Discretion Quiet and harmonious operation Minimal footprint Compact and monolithic brushed stainless steel housing Transparent glass panels Security Non-removable arms Mechanical locking withstands force Applications: Banks and insurance companies Governmental and institutional establishments Office buildings, registered offices, administrative sites Hospitals and medical centers

The transmitter converts the tilt angle into a direct current signal, proportional to the angle. Tilt angle values of a platform stand for important measuring data as a part of the safety and control system of that type of machinery. • Robust magnetoresistive CANopen angular position transmitter, conctact free, freely rotatable without stops • With oil-damped pendulum system • The sensor is contact free and has minimal abrasion on the pendulum • Pendulum shaft has no mechanical stops and can be 360° infinitely rotated • Reduced wiring expenditure • Autoconfiguration of the network • Comportable access of all instrument parameters • Instrument synchronisation, simultaneous data read-in and read-out

The transmitter converts the tilt angle into a direct current signal, proportional to the angle. Tilt angle values of a platform stand for important measuring data as a part of the safety and control system of that type of machinery. • Robust magnetoresistive angular position transmitter with interface SSI, contact free, freely rotatable without stops • With oil-damped pendulum system • The sensor is contact free and has minimal abrasion on the pendulum • Measuring range, sense of rotation, zero position and measuring span programmed directly at the transmitter

The transmitter converts the tilt angle into a direct current signal, proportional to the angle. Tilt angle values of a platform stand for important measuring data as a part of the safety and control system of that type of machinery. • Robust magnetoresistive angular position transmitter, conctact free, freely rotatable without stops • With oil-damped pendulum system • The sensor is contact free and has minimal abrasion on the pendulum • Measuring range, sense of rotation and zero position programmed directly at the transmitter

Welding process for each corners of Pvc profiles at sime time Welding feature for white and colory profiles Welding feature of 2 x 90 degree with just one process 90 degree easy welding process on moveable working table Full automatic head control system More safety welding pressure and profile pressure adjustment pneumatic fixing/brake system for right corner Mor sentitive welding process by sliding bearings on right welding corner 0.2mm esthtetic finished welding at white and colory profiles Easily changeable single piece tefon sheet wrap Maximum welding strength

SAFETY SYSTEM AND ADVANCED SOLUTIONS: - Safety access control with key removal systems; - CCTV systems grant high safety standards and a constant and effective production control; - Integration between SCADA screens and real-time images of the plant; - Continuous recording with play-back option; - Camera system also on wireless technology and fiber optic; - Historical and Analysis with trend systems; - Material shape detection devices.

The IU-01 Industrial Panel is a human-machine interface based on industrial PC architecture and originally designed as a part of a train safety system for guiding an operator to monitor and control a rolling stock drive including overspeeding control, temperature, motioning, safety and other train systems control. Its dependable performance and robustness allows applying IU-01 in other harsh environments to operate automobile and marine vehicles as well as agricultural and customized machinery and equipment. IU-01 can be associated with a numerous functional systems of vehicles, and its functionality can be programmed as per customer specific requirements.

Tilt angle values of a platform stand for important measuring data as a part of the safety and control system of machinery. Angular measurement is, for instance for equipment levelling, performed in such cases by means of dual axis pendulum systems. Transducers of that type contain inside a robust splash-proof aluminium case of protection degree IP 65 to IP 68 oil-damped pendulum systems, the tilt angle dependant swing of which is measured, depending on the application, either by a potentiometric, non-contact inductive or an optoelectronic angular encoder. For measurements relevant to safety, the pendulum swing per axis is detected with redundancy i.e. by means of two mechanically and electrically independent pendulum systems. The output signal, representing the tilt angles, is provided either in form of an analog resistance, current or voltage variation or as a digital signal - with interface bus - as well.