Results for
AFS ENTWICKLUNGS + VERTRIEBS GMBH
Germany
Measurement of the surface tension The adhesion of a surface is usually directly dependent on the surface energy. If the surface energy is substantially lower than that of the printing ink used, the wetting is disturbed, resulting in poor adhesion. For this reason, plastic surfaces have to be pre-treated. Depending on the type of ink used the surface tension required can vary: solvent based inks => 38 bis 42 mN/m (=Dyn/cm) water soluble inks => 40 bis 44 mN/m UV inks => 44 bis 46 mN/m With the test inks of AFS, which are available from 34 to 56 dyn/cm surface tensions of plastic films can be easily and reproducibly determined according to DIN ISO 8296. Depending on whether the ink sticks or bubbles on the surface it indicated whether the surface tension is above or below the dyne-value of the currently used test ink. We also offer the test inks in a case with 12 bottles from 34 to 56 dyn/cm.
Request for a quoteDPL INDUSTRI A/S
Denmark
DPL SpeedyTM UV LED INK Testing system use sliding block to carry ink sample or radiation meter by Linear Motion system with servo driver +Integrated PLC control to reach precision measurement at speed from 4-300m/min. Our clients set testing speed and UV Energy on Touch screen, Sliding block with ink sample run automatic at the setup speed when it pass the curing area,in the meanwhile lamp will be automatic reach the setup energy. After curing, the sample will be automatic return back to the start position. SpeedyTM UV LED Ink testing system provides real-time picture for your curing result same as your printing machines. Why DPL UV LED INK Testing system? High speed: up to 300m/min easy switch Multi-light source: UV Lamp or LED Lamp easy swich on/off Multi-wave length: 365,385,395,410nm
Request for a quoteDEKORTECH GMBH
Germany
Water based, pigment ink for DTF (direct to film) printing. ✔ Fine pigment dispersion ✔ OEKO-TEX certified ✔ Great prices ✔ Intense colors ✔ Low clogging ✔ Approved for EPSON i3200-A1 print heads Colors: CMYK+White, Spot colors, fluorescent colors Our DTF inks are tested and approved for DTF printing. With particles smaller than 0.3μm they can be used in a wide range of print heads. The unique formulation creates a perfect balance of color density and drying behavior. By this we make sure that your print heads stay open for as long as possible without sacrificing the opacity of your prints. With spot or fluorescent colors, you can run these inks in 2, 3 and 4 head printers to increase your color gamut or add special effects. The overall compatibility of these inks makes them a great and affordable partner for many adhesives powders and films.
Request for a quoteBIO STROHHALME GMBH
Germany
Paper drinking straws according to highest standards and most stringent European quality requirements. -thicker than comparable Asian or US paper drinking straws -extremely stable as they do not dissolve in water for at least 2 h -bio degradable and 100 % compostable. -made of food-safe and approved materials and inks -100% free of lead, chlorine and softeners. -they comply with various European guideline and FDA regulations about paper products with food contact -the straws are halal, kosher and vegan -also the straw inks are tested and certified according a.m. EU regulations -5-6 years shelf life under proper and dry storage conditions -not for hot beverage. Available in small household sizes and larger units for gastronomy -the straws are 100% Made in Germany and also the FSC certified paper and the relevant glues are of German origin. -the straws are packed in our certified and environmental friendly design boxes made of craft paper
Request for a quoteDIENER ELECTRONIC GMBH & CO. KG
Germany
A prerequisite for the adhesion of an adhesive or coating to a surface is wetting. For wetting to take place, the surface energy of the substrate must be greater than that of the coating. In particular, very many plastics have a very small surface energy and are correspondingly difficult to bond. Often the aim of a plasma treatment is to make a surface wettable and bondable. The wettability can easily be tested with test inks. Diener electronic supplies a test ink set with 8 liquids with surface tensions between 30 and 73 (105) mN/m suitable for most practical applications. There is also a set of 23 test inks, with additional gradations between 30 and 73 (105) mN/m.
Request for a quoteASTRONOVA GMBH
Germany
The T3-OPX is the perfect direct-to-package solution, providing the flexibility to print directly onto a wide range of materials with ink-receptive surfaces such as cardboard, postcards, envelopes, boxes, paper bags, wooden planks, or thicker objects like blister envelopes or folded boxes ready for shipment. The T3-OPX automates the product handling and printing process, resulting in greater efficiency and higher profitability for all businesses, including large brand owners or commercial printers. The durable pigmented inks are tested for superb lightfastness, water, and scratch resistance on a wide range of printable materials. Unique, self-calibrating, adjustable product height ensures optimal print quality while providing fast product changeovers, helping you to meet rigorous production demands. The Print width of up to 297 mm supports a wide range of product sizes on a single device. This solution is versatile to expand your products and services - private labeling!
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
Results for
Ink test - Import exportNumber of results
6 ProductsCountries
Company type