Results for
FOCQUET
Belgium
"Focquet offers three-phase induction motors in cast iron or aluminum housings. The dimensions and power correspond to the values of a standard motor, but have been modified to allow braking applications. The disc brake is supplied with direct or three-phase alternating current by a rectifier located in the motor terminal block. Our solution is always a parking brake. Standard motor size and power rating, aluminum and cast iron chassis."
Request for a quoteHENSE SYSTEMTECHNIK GMBH & CO. KG
Germany
The swivel motors with attached hydraulically released spring-applied multi-disc brake are recommended if a swivel position must remain unchanged once it has been reached – even over an unlimited period of time – despite the effect of a load torque. The brake is used solely to hold the load. It should only be noted that large transmission delays in the lines can cause time differences between the switching off of the swivel motor and the application of the released brake caused by spring force. In order to provide our customers with the right drive for all areas of application, the HSB swivel motor is available in a total of 5 different versions. We have listed the most important data below. You can find all further details in our data sheet.
Request for a quoteHENSE SYSTEMTECHNIK GMBH & CO. KG
Germany
The swivel motors of the HSE series also fulfill the function of end position damping with or without adjustable swivel angle limitation. This refers to braking, the deceleration of the swivel movement to a standstill. For damping, the cross-section of the bore for the outflowing medium is continuously reduced, thus hydraulically slowing down the moving masses. The end position is reached when the hole is completely closed and the medium can no longer flow out. In order to provide our customers with the right drive for all areas of application, the HSE swivel motor is available in a total of 6 different versions. We have listed the most important data below. You can find all further details in our data sheet.
Request for a quoteLEROY SOMER
France
Advantages IP55 fully sealed splash-and dust in an industrial environment. More compact: gains in size and weight. Good resistance.
Request for a quoteIGUS® GMBH
Germany
Planetary gears for igus® stepper motors NEMA 23, 23XL & 34 Increased motor torque Increased brake holding torque 2 installation sizes Reduction gearing of 3 & 5 available Typical applications:Packaging technology, general mechanical engineering, inspection technology/ camera travel drylin® E data sheet - Gearbox for stepper motors GEA-60-..._EN.pdf Planetary gears for igus® stepper motors NEMA 23, 23XL & 34 Increased motor torque Increased brake holding torque 2 installation sizes Reduction gearing of 3 & 5 available Typical applications:Packaging technology, general mechanical engineering, inspection technology/ camera travel
Request for a quoteWEBER FOOD TECHNOLOGY GMBH
Germany
Combination machine for thick and thin: The AMS 533 TWIN skinning machine is particularly suited to processing cuts with thick tendonsand skin, such as pork loin, pork silverside, beef or veal silverside and boiled beef fillet. Advantages Removal of tendons and skin with one machine TWIN transport rollers and specially coordinated blades providethe highest possible yields Ideal cutting width for powerful skinning and tendon removal inlarge and small cuts Effort-saving work table design due to ergonomicmachine assembly Blade guard in cleaning position Gear brake motor with quick stop Product-specific precision adjustment Options: Quick-clamp blade holder for tool-less blade changing Body lever switch Skinning procedure protection Skinning gloves Special tension rollers
Request for a quoteDEMAG CRANES & COMPONENTS GMBH
Germany
Our motors perform a wide variety of industrial drive tasks. Reliably and effectively. For example, our type Z cylindrical-rotor brake motors – also as brake motors – offer high drive efficiency – also in continuous duty. They are specially designed to match our gearbox range and provide for simple project engineering. Our conical-rotor brake motors with outputs of up to 55 kW are used for stopping-and-starting drives or for direct line-fed travel applications. Thanks to their unique brake principle, they are the first choice wherever demanding requirements have to be met by the brake.
Request for a quoteWEBER FOOD TECHNOLOGY GMBH
Germany
Powerful derinding machine for large and small pieces of cheese. In addition to an ideal cutting width, the Weber Cheese Skinner offers product-specific height adjustment of the blade, meaning that natural and plastic rinds can be optimally removed. Maximum product yield is guaranteed. Advantages Powerful and with a compact footprint A special cheese transport roller and perfectly adjusted blades for optimal processing results Ideal cutting width for powerful derinding of large and small pieces of cheese Bolted blade with blade protection in cleaning position Unique geared brake motor with quick stop Options: special voltages
Request for a quoteRK ROSE+KRIEGER GMBH
Germany
The completely equipped electrical cylinder unit includes the motor transmission unit, along with the motor brake, two-channel Hall-IC sensor and two end-limit switches. All connection lines run directly out of the unit to make configuration and initial start-up easier, particularly for PLC operation. The fixation of the electric cylinder connections is compatible with commercial pneumatic and hydraulic cylinders.
Request for a quoteWEBER FOOD TECHNOLOGY GMBH
Germany
One for many purposes: Powerful skinning machine for large and small cuts of beef, veal, pork, turkey, horse and game. The Skinner AMS 533 offers an ideal cutting width for processing large cuts, such as beef topside. Advantages Powerful for the highest yield from the smallest installation area Product-specific optional transport rollers and speciallycoordinated blades provide the highest possible yield Ideal cutting width for powerful skinning of large and small cuts Blade guard in cleaning position Gear brake motor with quick stop Product-specific tension rollers Newly-developed compressed air transport roller cleaning,resulting in consistent skinning results Options: Body lever switch Quick release lock for tool-free blade changes Special rollers Skinning procedure protection Special tension rollers
Request for a quoteJ.D. NEUHAUS GMBH & CO. KG
Germany
JDN air hoists mini Carrying capacities: 125 kg, 250 kg, 500 kg, 980 kg Air pressure: 6 bar Standard Features interesting and inexpensive alternative even to hoists with other driving media suitable for lube-free operation suitable for application in hazardous areas (Explosion protection) few components only for easiest maintenance wear resistant motor braking system light weight for easy handling also suitable for horizontal pulling extremely sensitive lever control with emergency shut-off valve, max. control length 6 m available lifting heights: 3m, 5m, 8m with chain box as standard with manual trolley as option
Request for a quoteGSW SCHWABE AG
Germany
Strong plasmaburned back plate provides smooth and straight operation Removable and adjustable hub disk Fast and precise expansion via bevel gear with exceptionally wide ranges, allows clamping of all internationally common coil sizes From 1000 kg capacity equipped with lever type expansion Alternatively with guide rod coil fixation instead of expansion system (mainly for pallets) Pneumatic hold down arm Motorized pivoting Electropneumatic brake system Larger mandrel segments Traveling feature Different loading heights Various expansion ranges Different back plate sizes Loop control systems
Request for a quoteGSW SCHWABE AG
Germany
Effortless 180° rotation via foot pedal and automatic mechanical locking Optional sensory position readout Crank Expansion via directionally stable joints, easily operable even under weight Highestquality Reel Arbor with maintenancefree bearing and minimal deflection Sturdy and warp resistant body in welded construction for highest stability MHD Series PullOff Reel with manually adjustable brakes MHDM Series Payoff Reel with threephase motors for start / stop operation MHDR Series Payoff Reel with threephase motors and frequency inverter for continuous operation Optional Equipment MHDSeries Pneumatic hold down arms Electropneumatic brake systems Larger mandrel segments Motorized rotation Traveling feature w optional automatic centering Different mandrel heights Various expansion ranges Different back plate sizes Loop control systems...etc.
Request for a quoteHENSE SYSTEMTECHNIK GMBH & CO. KG
Germany
The use of servo-hydraulic controls can significantly extend the range of applications for swivel motors. Larger loads can be slewed in a shorter time than is possible with purely hydraulic systems, where the damping travel is fixed. In conjunction with such a control system, the acceleration and braking behavior of the swivel motors can be specifically adapted to the requirements. This means that even fast and very precise movements with large masses can be safely mastered. We offer customized solutions for a wide range of applications. Our qualified team will be happy to advise you on design and realization.
Request for a quoteALKIM PETROKIMYA
Turkey
It is a high performance hydraulic brake and clutch system fluid based on synthetic poly glycol developed for use in the hydraulic brake systems and clutch of motor vehicles in the wide range of applications. It is formulated for the vehicle systems with the requirement of DOT3 standard brake and clutch fluid. lts high thermal and chemical stability ensures efficient operation of the braking system in all kinds of climate and road conditions.
Request for a quoteHENSE SYSTEMTECHNIK GMBH & CO. KG
Germany
The use of servo-hydraulic controls can significantly extend the range of applications for swivel motors. Larger loads can be slewed in a shorter time than is possible with purely hydraulic systems, where the damping travel is fixed. In conjunction with such a control system, the acceleration and braking behavior of the swivel motors can be specifically adapted to the requirements. This means that even fast and very precise movements with large masses can be safely mastered. We offer customized solutions for a wide range of applications. Our qualified team will be happy to advise you on design and realization.
Request for a quoteHENSE SYSTEMTECHNIK GMBH & CO. KG
Germany
The use of servo-hydraulic controls can significantly extend the range of applications for swivel motors. Larger loads can be slewed in a shorter time than is possible with purely hydraulic systems, where the damping travel is fixed. In conjunction with such a control system, the acceleration and braking behavior of the swivel motors can be specifically adapted to the requirements. This means that even fast and very precise movements with large masses can be safely mastered. We offer customized solutions for a wide range of applications. Our qualified team will be happy to advise you on design and realization.
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
HENSE SYSTEMTECHNIK GMBH & CO. KG
Germany
The use of servo-hydraulic controls can significantly extend the range of applications for swivel motors. Larger loads can be slewed in a shorter time than is possible with purely hydraulic systems, where the damping travel is fixed. In conjunction with such a control system, the acceleration and braking behavior of the swivel motors can be specifically adapted to the requirements. This means that even fast and very precise movements with large masses can be safely mastered. We offer customized solutions for a wide range of applications. Our qualified team will be happy to advise you on design and realization.
Request for a quoteHENSE SYSTEMTECHNIK GMBH & CO. KG
Germany
The use of servo-hydraulic controls can significantly extend the range of applications for swivel motors. Larger loads can be slewed in a shorter time than is possible with purely hydraulic systems, where the damping travel is fixed. In conjunction with such a control system, the acceleration and braking behavior of the swivel motors can be specifically adapted to the requirements. This means that even fast and very precise movements with large masses can be safely mastered. We offer customized solutions for a wide range of applications. Our qualified team will be happy to advise you on design and realization.
Request for a quoteHENSE SYSTEMTECHNIK GMBH & CO. KG
Germany
The use of servo-hydraulic controls can significantly extend the range of applications for swivel motors. Larger loads can be slewed in a shorter time than is possible with purely hydraulic systems, where the damping travel is fixed. In conjunction with such a control system, the acceleration and braking behavior of the swivel motors can be specifically adapted to the requirements. This means that even fast and very precise movements with large masses can be safely mastered. We offer customized solutions for a wide range of applications. Our qualified team will be happy to advise you on design and realization.
Request for a quoteBERTAZZON 3B SRL
Italy
The Swing Carousel consists of a rotating structure supporting one row of swinging chairs. The whole structure is hot-dip galvanised, with exception of the central column and is covered by hand painted decorative fibreglass panels on which lighting is fixed. The swinging chairs and their supporting chains are made by stainless steel while the seat is made out of fiberglass. The covering roof is made up by a flame-retardant canvas. The rotation is made by one self-braking AC motor.
Request for a quoteBERTAZZON 3B SRL
Italy
Single Decker Horses Merry-go-Round after the 18th century fashion. The carousel consists of an hot-dip galvanised rotating structure supported by a central column and covered by hand decorated fibreglass panels on which lighting is fixed. The floor structure is suspended from the ground by tie-bars hanged to the roof and the floor surface consist of clear coated solid hard-wood panels. The driving unit consist of AC self-braking gear-motor mounted to the central column and electronically controlled. All Jumping horses and the rocking chariot are moved by ball bearing mounted crankshafts located on the ceiling.
Request for a quoteBERTAZZON 3B SRL
Italy
Single Decker Horses Merry-go-Round, Liberty style. The carousel consists of an hot-dip galvanised rotating structure supported by a central column and covered by hand decorated fibreglass panels on which lighting is fixed. The floor structure is suspended from the ground by tie-bars hanged to the roof and the floor surface consist of clear coated solid hard-wood panels. The driving unit consist of AC self-braking gear-motor mounted to the central column and electronically controlled. All Jumping horses and the rocking chariot are moved by ball bearing mounted crankshafts located on the ceiling.
Request for a quoteBERTAZZON 3B SRL
Italy
Single Decker Horses Merry-go-Round after the 18th century fashion. The carousel consists of an hot-dip galvanised rotating structure supported by a central column and covered by hand decorated fibreglass panels on which lighting is fixed. The floor structure is suspended from the ground by tie-bars hanged to the roof and the floor surface consist of clear coated solid hard-wood panels. The driving unit consist of AC self-braking gear-motor mounted to the central column and electronically controlled. All Jumping horses and the rocking chariot are moved by ball bearing mounted crankshafts located on the ceiling.
Request for a quoteBERTAZZON 3B SRL
Italy
Single Decker Horses Merry-go-Round after the 18th century fashion. The carousel consists of an hot-dip galvanised rotating structure supported by a central column and covered by hand decorated fibreglass panels on which lighting is fixed. The floor structure is suspended from the ground by tie-bars hanged to the roof and the floor surface consist of clear coated solid hard-wood panels. The driving unit consist of AC self-braking gear-motor mounted to the central column and electronically controlled. All Jumping horses and the rocking chariot are moved by ball bearing mounted crankshafts located on the ceiling.
Request for a quoteBERTAZZON 3B SRL
Italy
Single Decker Horses Merry-go-Round after the 18th century fashion. The carousel consists of an hot-dip galvanised rotating structure supported by a central column and covered by hand decorated fibreglass panels on which lighting is fixed. The floor structure is suspended from the ground by tie-bars hanged to the roof and the floor surface consist of clear coated solid hard-wood panels. The driving unit consist of AC self-braking gear-motor mounted to the central column and electronically controlled. All Jumping horses and the rocking chariot are moved by ball bearing mounted crankshafts located on the ceiling.
Request for a quoteBERTAZZON 3B SRL
Italy
Single Decker Horses Merry-go-Round after the 18th century fashion. The carousel consists of an hot-dip galvanised rotating structure supported by a central column and covered by hand decorated fibreglass panels on which lighting is fixed. The floor structure is suspended from the ground by tie-bars hanged to the roof and the floor surface consist of clear coated solid hard-wood panels. The driving unit consist of AC self-braking gear-motor mounted to the central column and electronically controlled. All Jumping horses and the rocking chariot are moved by ball bearing mounted crankshafts located on the ceiling.
Request for a quoteBERTAZZON 3B SRL
Italy
Single Decker Horses Merry-go-Round after the 18th century fashion. The carousel consists of an hot-dip galvanised rotating structure supported by a central column and covered by hand decorated fibreglass panels on which lighting is fixed. The floor structure is suspended from the ground by tie-bars hanged to the roof and the floor surface consist of clear coated solid hard-wood panels. The driving unit consist of AC self-braking gear-motor mounted to the central column and electronically controlled. All Jumping horses and the rocking chariot are moved by ball bearing mounted crankshafts located on the ceiling.
Request for a quoteBERTAZZON 3B SRL
Italy
The Galleon Race ride consist of a circular development track with depressions and two “cat’s back”. The rail is supported by a steel horse structure, connected to the central body by radial longeron and tie rods. The whole metal structure is hot-dip galvanised. Twelve cars run along the rail, connected to a central rotor by radial arms (sweeps). The foot-boards approaching the cars consists of an aluminium tread plate. All electric and pneumatic equipment is fitted inside the central body, on which the central rotor is fixed. The ride moves by means of 1 self-braking A.C. gear-motor fixed to the central rotor and controlled by Frequency Drive.
Request for a quoteResults for
Brake motors - Import exportNumber of results
72 ProductsCountries
Company type
Category