Fingering - Import export

FE C series finger joint suitable to absorb decks displacements from 300 mm (± 150) to 600 mm (± 300) consisting of: • overhung finger elements of CORTEN steel; • mechanical anchoring system consisting of multidirectional clamps and anchor rods; • stainless steel gutter; • "L"-shaped stainless steel profile for under pavement waters drainage; • epoxy mortar strips connecting the joint elements and the bituminous pavement. JOINT TYPE TOTAL MOV. (mm) HEIGHT H (mm) WIDTH*X (mm) GAP *Y (mm) ANCHORS Z (mm) ANCHORS T (mm) FE C 300 300 55 760 220 100 115 FE C 400 400 65 890 270 105 150 FE C 500 500 75 1040 320 110 195 FE C 600 600 85 1210 370 130 235 FE C 700 700 115 1310 420 145 250 FE C 800 800 120 1470 470 150 300 Length of finger element = 480 mm * average gap POS. DESCRIPTION MATERIAL A Finger element S355J2WP EN 10025 B Sealant EPOBLOCK ME Legante C Transition strip EPOBLOCK ME 3C D Bedding EPOBLOCK ME 3C / Beton FIP E M16 anchoring system F M24 anchoring system G Gu

GP-type steel finger joints suitable to absorb deck displacements of up to 250 mm (+ I 25) consisting of: • anchoring/support system made of patented anchor rods of suitable section and length; • suitably dimensioned and shaped stainless steel gutter. • active upper part consisting of an overhung metal finger system obtained by the processing of COR-TEN steel plates equipped with bolts, nuts, washers etc.; • under-pavement waters drainage consisting of stainless steel "L"-shaped profile. JOINT TYPE TOTAL MOV. (mm) HEIGHT H (mm) WIDTH*X (mm) GAP *Y (mm) ANCHORS Z (mm) ANCHORS T (mm) ANCHORS ø (mm) GP 50 50 30 400 60 80 45 M16 GP 100 100 30 470 80 105 45 M16 GP 150 150 35 545 105 130 45 M20 GP 200 200 40 620 130 155 45 M24 GP 250 250 45 820 155 180 45 M24 Length of finger element = 480 mm * average gap POS. DESCRIPTION MATERIAL A Finger element S355J2WP EN 10025 B Sealant EPOBLOCK ME Legante C Transition strip EPOBLOCK ME 3C D Bedding EPOBLOCK ME 3C / Beton FIP E Anch

Expansion joint specifically designed for highway use within structures creating longitudinal movements of ± 15 (mm), vertical movements up to 10mm. It consists of an extruded rubber bellows, vulcanized to two 80x80x9 mm T-profiles and anchored to the slab by clamps of suitable diameter, placed at a centre distance of 240 mm. The extruded rubber, together with the steel profiles it is vulcanized to, makes up a water-tight system and seamlessly covers the entire width of the road bed. Water-tight capacity around the areas close to the joint is ensured by appropriate water-proof materials. POS. DESCRIPTION MATERIAL A 65x80x9 finger "T" profile S235JR EN 10025 B Vulcanized rubber profile CR 65 sh/a cnr 10018 C A.M. clamp Ø 16x150÷200 FeB 44K D Construction joint Fibre-reinforced cement mortar E Gutter Hypalon F "L" shaped drainage profile X5 CrNi 1810-UNI 8317 G Epoxy-resin mortar H Road surface

These joints are obtained by opposing two finger-shaped metal elements: each is fixed to its head, thus ensuring, thanks to a suitable interpenetration, continuity of the carriageway in case of expansion/shrinkage. Their static layout can act as a beam on two bearings when the finger rests on both heads or as a shelf when it overhangs a head. A specific device is needed, usually a gutter, to ensure the gap watertightness. Special attention should be paid to the alignment during the installation phase and to the head anchoring, especially in the case of shelf layout. Except for special arrangements, this type of joint permits limited transverse displacements. TIPOLOGIE: SFE 90/65 GP FE C