Results for
SCHNELL SPA
Italy
Automatic mesh bending machine, equipped with double gearmotor, fast fitting pins. It is equipped with Reinforced framework; Bending pin holder; Adjustable mobile bending bar (minimum length 70 mm); 'KS31' electronic digital programmer which allows adjusting bending angles.
Request for a quoteSCHNELL SPA
Italy
Bar bending machine. Bending disk and adjustable strength steel saddles. Capacity 1 bar Ø 32 mm (#10) Plate revolving speed 9 RPM
Request for a quoteSCHNELL SPA
Italy
Bar bending machine. Bending disk and adjustable strength steel saddles. Capacity 1 bar Ø 45 mm (#14) Plate revolving speed 5÷12 RPM Equipped with electronic programmer up to 50 bends
Request for a quoteSCHNELL SPA
Italy
Ring bending machine for rings of unlimited radius (rib rings) and spirals. Driven by a variablespeed electric motor min 20; max 30 rpm. Adjustable bending radius from a minimum 15 cm (with small diameters) and over. For Ø 6 mm (#3) Ø 32 mm (#10) wires.
Request for a quoteSCHNELL SPA
Italy
Bar bending machine. Bending disk and adjustable strength steel saddles. Capacity 1 bar Ø 36 mm (#11) Plate revolving speed 8 RPM
Request for a quoteSCHNELL SPA
Italy
Dualdirection bar bending machine with threespeeds selfbraking motor driven by inverter. The machine doesn't pull the bars during bending operations. The equipment is driven by a selfbraking motor. Electronic digital programmer mod. 'KS31' which allows Programming stirrups and shapes with up to 30 bends; Adjusting bending angles; Storing up to 50 different shapes.
Request for a quoteSCHNELL SPA
Italy
Automatic double bending machine for bars up to Ø 50 mm (#14). It works automatically and bends any kind of shapes, positive and negative bends included. Automatic system for bars feeding and discharging Ejection cylinder pneumatic ejector for shapes and mandrels to remove the tools from the toothed part Operation by means of digital electric servomotors 4 adjustable bending speeds
Request for a quoteSCHNELL SPA
Italy
Automatic steel ring bending machine for the production of circles, spirals and radius bars for diameters from Ø 6 mm (#3) to Ø 40 mm (#14). The machine uses a system of 4 rollers, one of which is specifically to ensure the stability and consistency of the radius of the curve. The rebar combined machine CER40 can be programmed to produce automatically up to 5 different radius curves on the same bar thanks to the measuring system.
Request for a quoteSCHNELL SPA
Italy
Automatic double bending machine for bars up to Ø 50 mm (#14). It works automatically and bends any kind of shapes, positive and negative bends included. Version with automatic feeding and discharging units, which fold away (Optional) they allow the minimum distance of 980 mm between the two bending mandrels. Automatic system for bars feeding and discharging Ejection cylinder pneumatic ejector for shapes and mandrels to remove the tools from the toothed part the positions of the clamps and guides on the kick off arms and their adjustment are motorized and automatic Operation by means of digital electric servomotors 4 adjustable bending speeds
Request for a quoteSCHNELL SPA
Italy
Four speed dualdirection bar bending machine. It doesn't pull the bars during bending operations. Driven by digital electric servomotors. Industrial PC equipped with touch screen graphic display 8'', which allows Programming stirrups and shapes with up to 30 bends; Adjusting bending angles; Storing up to 100 different shapes.
Request for a quoteSCHNELL SPA
Italy
IPC 40 is the plant for the production of radius bars with bends in a single, automatic process. It is composed of the radius machine CER 40, the bidirectionalbending machine P 45 PRO and has an unloading system for the completed bars. It is possible to fabricate 2 bars simultaneously in the diameter range between Ø10 mm and Ø 40 mm.
Request for a quoteSCHNELL SPA
Italy
Automatic mesh bending machine, equipped with double gearmotor, fast fitting pins and switch for 3 mechanical programs. It is equipped with Reinforced framework; Bending pin holder; Adjustable mobile bending bar (minimum length 70 mm);
Request for a quoteSCHNELL SPA
Italy
Automatic rebar bending machine for bars up to Ø 40 mm. It works automatically and bends any kind of shapes, positive and negative bends included. Automatic system for bars feeding and discharging 2 adjustable bending speeds
Request for a quoteSCHNELL SPA
Italy
Automatic bar bending machine for the production of shapes with positive bends (“L”, “C” and double “C”), up to Ø 40 mm (#11). Device for the production of "bottlenecks“. Automatic system for bars feeding and discharging.
Request for a quoteSCHNELL SPA
Italy
Multirotor straightening and shaping machine using coils up to Ø 20mm for the production of straight bars, large stirrups and shapes with bends on both ends. 4 wheel drive pulling unit driven by servomotors for high speed production; Maximum pulling speed 140 m/minute; The straightening system uses rotors, each one dedicated to a single bar diameter which guarantees perfectly straight bars and wire diameter changes in just a few seconds; Servomotor driven cutting unit guarantees high speed and high cutting accuracy; 2 bidirectional bending units work “offline” so the bars are bent in “masked time”; Automatic bending tooling changeover for higher productivity; Indexing carriage for the automatic collection and sorting of the bars produced.
Request for a quoteSCHNELL SPA
Italy
Stirrup bender and bar shaping machine from coil with 2 bending heads, allows to produce stirrups and shaped wires with bends at both ends using wires up to Ø 25 mm (#8). Driven by electric servomotors. These automatic stirrup benders and bar shaping machines are equipped with Max. pulling speed 160 m/min (525 ft/min) Straighteners (horizontalvertical) with electronic and independent setting for the 2 wires with Joystick Patented feed unit that allows independent advancement for single o double wire (Optional) 2 bending unit Automatic motorized wire change Automatic adjustable wireguide Web Teleassistance Prestraightening Feeding Unit (Optional).
Request for a quoteSCHNELL SPA
Italy
Stirrup bender and bar shaping machine from coil with 2 bending heads for the production of stirrups and shaped wires with bends at both ends using wires up to Ø 16 mm (#5). Driven by electric servomotors. Also available HS version machine. These automatic stirrup benders and bar shaping machines are equipped with Max. pulling speed 140 m/min (460 ft/min) HS Version 200 m/min (660 ft/min) Straighteners (horizontalvertical) with electronic and independent setting for the 2 wires with Joystick AntiTwist electronic device (Optional) Patented feed unit that allows independent advancement for single o double wire (Optional) 2 bending unit (upper and lower) 4 pulling drive wheels Cutting unit with adjustable wire guide, reversible mobile and fixed cutting blades Web Teleassistance 3D version for the production of tridimensional pieces.
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
SCHNELL SPA
Italy
Electromechanical automatic mesh cutting and bending machine for the production of U, L, Zshaped mesh and sandwich panels. Mesh handling is guaranteed by clamps driven by electric servomotors. Max mesh width 1250 mm; Max mesh length 6000 mm.
Request for a quoteResults for
Bending - Import exportNumber of results
19 ProductsCountries
Company type