Horizontal pumps - Import export

The horizontal Pump tube is suitable for emptying highly aggressive, thin-bodied, flammable and explosive liquids from IBC containers or tanks and is the perfect alternative to the vertical Drum Pumps. Depending on the application, different Motors are available, which you can combine with the Pump tube at any time. This means you are flexible at all times and thus save important resources. * Horizontal connection at the bottom run of the container * Pump tube equipped with Lutz original hand wheel * Suitable for emptying alternative fuels, oils, flammable liquids * Optionally with electric or compressed air drive * Low loss of medium when disconnected * Explosion-proof versions for applications in hazardous areas (Zone 1 and 2) * Easy to dismantle * Low space requirement

The horizontal Pump Set is suitable for emptying highly aggressive, aqueous to slightly viscous media from IBC containers or tanks and is the perfect alternative to the vertical Drum Pumps. Perfectly suited for the discharge of concentrated acids and alkalis. * Optionally with leakage detection (Safety Box) * Horizontal connection at the bottom of the container Features & Advantages * Optionally with electric or compressed air drive * Low loss of medium when disconnected * Simple installation * Easy to dismantle * Small footprint * Automatic emergency stop function of the motor in case of leakage detection

The horizontal Pump tube is suitable for emptying highly aggressive, aqueous to slightly viscous media from IBC containers or tanks and is the perfect alternative to the vertical Drum Pumps. Perfectly suited for the discharge of concentrated acids and alkalis. * Optionally with leakage detection (Safety Box) * Horizontal connection at the bottom of the container * IBC connection: S60 x 6 Features & Advantages * Optionally with electric or compressed air drive * Low loss of medium when disconnected * Easy to install * Easy to dismantle * Small footprint * Automatic emergency stop function of the motor in case of leakage detection * The maximum flow rate is a value determined by means of a test bench and measured with water at a liquid temperature of approx. 20 °C . The measurement is taken at the pressure joint of the pump, without hose, nozzle or flow meter.‌

without shaft seal streamlined housing made of PP or ETFE volume flow of MA pump type 2 is up to 80 l/min, of MA pump type 3 up to 100 l/min discharge head of MA pump type 2 is up to 8m.Wg, of MA pump type 3 up to 15m.Wg horizontal single-stage monoblock design

The horizontal Pump tube is suitable for emptying aqueous and fatty food from IBC containers or tanks and is the perfect alternative to the vertical Drum Pumps. Depending on the application, different Motorsareavailable , which can be combined with the Pump tubeat any time. This gives you flexibility at all times, thus saving important resources. * Horizontal connection on the bottom run of the container * Pump tube equipped with Lutz original hand wheel * also for foodstuffs containing alcohol, cosmetics and pharmaceutical products as well as flammable cleaning agents Features & Advantages * Optionally with electric or compressed air drive * Low loss of the medium when disconnected * Food grade connections * Low space requirement * Approved according to FDA and regulation (EG) 1935/2004

One of the priority areas in the production of Villina pumping equipment was initially the development of a specialized line of pumps designed for pumping harsh chemical fluids. At present, we are ready to offer you Villina high-end lined centrifugal canned pumps having design life of 20 years for pumping mineral and organic acids, alkalis, salts, oxides and anhydrides, including chlorides, as well as alcohols, esters, aromatic hydrocarbons, ketones, aldehydes and other media which contain various concentrations of mordant substances. Modern technology makes rapid progress, and in place of pumps used earlier for transit of corrosive fluids made of chemically resistant yet expensive steels such as KhN65МV, N70MFV, 06KhN28MDT, lined pumps are widely used now. In accordance with para. 51 of the Safety Rules of chemically hazardous production facilities, corrosion-resistant non-metallic coatings (polyethylene, fluoroplastic) can be used to protect equipment and pipelines

Centrifugal pumps have well-known advantages such as uniform pumping without surges, the ability to create high pressures at low pump rate in multi-stage designs, long service life and others. Advantages: the fluid can be taken in at a point lower than the axis of the inlet suction pipe without using a pre-installed vacuum pump. - Purpose: transit of corrosive, toxic, explosive and flammable fluids at insufficient suction pressure; - Pump rate ranges: 0.8 to 450 m3/h; - Head ranges: 3 to 132 m; - Self-priming height (depth): up to 6 metres; - Seal type: magnetic coupling according to API 685 or tandem mechanical seal according to API 682; - Climatic version: for moderate and for moderate and cold climate; - Temperature of the pumped fluid: for GNGC-S, GNGC-S-M up to plus 350°С, for NCG-S up to plus 450°С; - Shaft speed: 1,450 or 2,900 rpm; - Structural design: ОН-2 single-stage back pull-out pump according to API 610 or a single block.

The ECO SNM close coupled, end suction, single stage horizontal centrifugal pump is standardised to DIN 24255 / EN 733 and can be used for a vast range of applications in the industrial and marine markets. It is designed to pump low viscosity clean or slightly contaminated fluids without the presence of solid or fibrous particles. If required, this pump is available in a vertical version known as the ECO SNM-V series. Typical Applications & Industries: - Water Treatment - Fresh, Grey or Sea Water - Fuels - Diesel, Petrol and Kerosene - Irrigation and Agriculture - Pressurisation - Draining and Dewatering - Building Systems - Marine - Cooling/Heating Conditioning (HVAC) - Chemical Transfer - and More

Horizontal End-Suction Pumps are centrifugal inline pumps with a compact design where the impeller is mounted onto the extended motor shaft. These pumps are not self-priming and must be gravity fed. All pumps are equipped with double mechanical seal. This pump series is designed for horizontal installations next to a tank and are capable of cutting aluminium chips and similar materials and pumping of these materials along with the coolant fluid. An agitator located at the pump suction helps to break up and separate any large bundles of chips or birds nests which reach the pump suction. The specially made cutting unit (>60 HRC) is cuting chips and the above located semi-open impeller allows with its large clearances to pump the particles along with the coolant fluid from the machine back to the filter. The SBC pumps are capable of handling chip to coolant ratios of up to 1.5% by weight. Volumetric delivery: up to 1400 l/min Delivery head: up to 34 m

Horizontal End-Suction Pumps are centrifugal inline pumps with a compact design where the impeller is mounted onto the extended motor shaft. These pumps are not self-priming and must be gravity fed. All pumps are equipped with a single mechanical seal. Upon request a second mechanical seal is available to allow for dry-running (-GD). This pump series is designed for horizontal installations next to a tank and for pumping air entrained coolant fluids, such as water-soluble coolants or cutting oils, as they occur in high speed turning, milling or grinding applications. The SBA pumps are equipped with the user-friendly (SAE) flange connection which allows for either vertical or horizontal pipe connection and the connection of a pressure gauge with G 1/4. Volumetric delivery: up to 2200 l/min Delivery head: up to 62 m Please contact us for delivery quantity.

The horizontal Drum and container pump F 430 TR is ideal for conveying media from IBCs, tanks and other containers with low level outlet. E.g. if a tank is not accessible from the top, or if the spatial conditions do not allow use of a vertical pump. For cleaning, the pump can be easily and quickly taken apart in its two main components. The pump is available in stainless steel or polypropylene. The stainless steel version can also be used in hazardous areas. Benefits: - For containers with floor drain - Provides highest flexibility in installation and mobility - Can also be used at low ceiling heights - Stainless steel version for use in hazardous areas - Can also be integrated into pipe systems - A horizontal centrifugal pump that can be used with different FLUX motors

The AM series was specially developed for for the medium performance segment in plant and apparatus engineering. High-quality housing and bearing materials enable adaptation to almost any conveying task as required. * Drive is via a magnetic coupling * Examples of applications: Acids, alkalis, acid and alkali mixtures, solvents, alkaline degreasing baths, electroplating baths, photographic chemicals Features & Advantages * Variable connection options * Compact dimensions, performance in line with requirements * Also for liquids with high density * Version "R" conditionally suitable for dry running * Motor and pump are mechanically separated * Connections with BSP thread or hose nozzle

The TMR series is a reliable magnetic drive pump that easily handles critical operating conditions due to its patented magnetic axial thrust compensation. * Drive via magnetic coupling with patented magnetic axial thrust compensation * Typical applications: Acids, alkalis, acid and alkali mixtures, solvents, alkaline degreasing baths, electroplating baths, photographic chemicals Features & Advantages * Variable connection options * Compact dimensions, performance in line with requirements * Also for liquids with high density * Due to "magnetic axial thrust balancing" the bearing system "R" is suitable for dry running * Motor and pump are mechanically separated * Connections with thread or flange

The TMB series was specially developed for installation in small systems and apparatus. The single-stage Centrifugal pump offers robust technology in the smallest space. * Drive is via a magnetic coupling * Typical applications: Acids, alkalis, acid and alkali mixtures, solvents, alkaline degreasing baths, electroplating baths, photographic chemicals Features & Advantages * Variable connection options * Compact dimensions, performance in line with requirements * Connections with BSP thread or hose nozzle * Ideal for mobile use * Motor and pump are mechanically separated

The horizontal pumping unit is suitable for emptying aqueous and fatty foodstuffs from IBC containers or tanks and is the perfect alternative to vertical drum pumps. Depending on the application, various motors are available, which you can combine with the pumping unit at any time. This gives you flexibility at all times and saves important resources. * Horizontal connection at the bottom of the container * Also for alcoholic foodstuffs, cosmetics and pharmaceutical products as well as flammable cleaning agents * Optionally with electric or compressed air drive * Low loss of medium when disconnected * Food-safe connections * Approved in accordance with ATEX Directive 2014/34/EU, category 1/2 * Approved according to FDA and Regulation (EC) 1935/2004 The value of the maximum flow rate is determined on the basis of fixed parameters and always under the same conditions. These can be found on our website.

The horizontal Pump Set is suitable for emptying highly aggressive, aqueous to slightly viscous media from IBC containers or tanks and is the perfect alternative to the vertical Drum Pumps. Perfectly suited for the discharge of concentrated acids and alkalis. * Optionally with leakage detection (Safety Box) * Horizontal connection at the bottom of the container Features & Advantages * Optionally with electric or compressed air drive * Low loss of medium when disconnected * Simple installation * Easy to dismantle * Small footprint * Automatic emergency stop function of the motor in case of leakage detection * The maximum flow rate is a value determined by means of a test bench and measured with water at a liquid temperature of approx. 20 °C . The measurement is taken at the pressure joint of the pump, without hose, nozzle or flow meter.‌

The horizontally installed, compact container pump MINIFLUX is designed for emptying IBCs via their floor-level outlet. Designed as an alternative to a vertical pump, the MINIFLUX can be used when an IBC is not accessible from the top. It is suitable for applications when gravity draining via the outlet tap is insufficient e.g. rapid dispensing or transfer to another container in a higher location. Power can ideally be provided by a commutator or compressed air motor. Benefits: - Can be used where ceilings are low - Allows pumping directly from floor-level outlets, even when containers are stacked - Significantly higher flow rate and pressure compared to draining by gravity - Minimal space requirement - Simple disconnection from IBC with union nut - Delivery against closed valve (e.g. hand nozzle, flap valve etc.) possible - Suitable for use in hazardous areas zone 1

Horizontal End-Suction Pumps are centrifugal inline pumps with a compact design where the impeller is mounted onto the extended motor shaft. These pumps are self-priming after initial filling. All pumps are equipped with a single mechanical seal. SBM Pumps are mounted next to or on top of the tank and they are suitable for pumping air entrained coolant fluids, such as water-soluble coolants or cutting oils, as they occur in high speed turning, milling or grinding applications. Volumetric delivery: up to 440 l/min Delivery head: up to 20 m Please contact us for delivery quantity.

Hemogum has its own recipes for mixtures with special requirements in the field of mining such as: mills with balls, shrink sleepers, rubber rotatory and stationary parts of horizontal and vertical pumps for handling of hydro mixtures with high resistance to abrasion. With Hemogum equipment we produce profiles of different diameters made from material of diverse quality, that attend requirements of the mining industry. In the construction area we produce spongy profiles, foils for acoustic and termo isolation, hydro isolation. Upon customer request foils can be made from different types of elastomer. Depending on the purpose, functions and customer request we make articles from: CR, NR, S8R, HR, BR, EPDM and NBR. In the field of energetics we produce electrical conductive mats, with width from 1 mm to 5mm. superficial resistence R<10 to 5<that is on 100000) W. Foils are NR. S8R quality orthe combination depending on its purposeand specific customers request. Foils may

10,000 PSI (700 BAR) COMPACT ELECTRIC TORQUE WRENCH PUMP The SPXFlow PE39 is compact and capable of being used in a vertical or horizontal orientation. Based on proven pump design for reliability in rugged torque wrench applications to support operation and maintenance requirements. Quality means Lower Life-Cycle Costs: Over 100,000 cycles Continuous duty up to 122˚F (50˚C) ambient Proven design = proven reliability Enhanced Usability: Light weight and portable: 39 lb (17.7 kg) Removable control pendant (15 ft / 5 m cord length) Removable 4" (100 mm) calibration-capable gauge Universal Motor for reduced voltage applications (up to -20% nominal voltage) Vertical or horizontal operation Easy install cooling fan as option Designed with Safety in Mind: Easily adjusted pressure regulator (relief) valve Fixed 1,500 psi (103 bar) retract relief valve pressure

* Set independent horizontal peristaltic pump * Ability to work with all infusion sets * Turkish Usage Menu * Microprocessor Controlled Reliable and Precise operation * KVO, Bolus and Purge functions * Audible and Visual alarms * Voiced alarm system * Optional docking station * HBYS

* LCD touch screen * Set independent horizontal peristaltic pump * Ability to work with all infusion sets * Turkish Usage Menu * Microprocessor Controlled Reliable and Precise operation * KVO, Bolus and Purge functions * Audible and Visual alarms

Horizontal canned pumps with welded bodies (Villina-GNGC) are designed for transit in stationary conditions of neutral, corrosive, toxic, as well as explosive and fire hazardous liquids, the vapors of which can form explosive mixtures with air. These pumps are used in petrochemical, petroleum refining and other industries. single-stage or multi-stage version of the unit design (increased discharge pressure, in contrast to back pull-out pumps); high efficiency of the impellers; a possibility to pump contaminated liquids with 100% tightness (for pumping units with combined seals); Temperature of the pumped fluid: up to +420°С.

The Villina GNGC series horizontal canned centrifugal pumps with magnetic couplings are widely used in oil and gas companies of Russia and its neighbouring countries for transit of explosive and flammable, toxic and corrosive fluids. The horizontal arrangement allows the use of a GNGC as a replacement for technically obsolete and physically worn pumps without significantly changing the geometry of the location and pump lines group assembly systems. 100% tightness, structural design in accordance with API 610, 685 (ISO 13709) standards and explosion-proof design of GNGC pumps are approved by design institutes and Rostekhnadzor for use in projects for modernization, reconstruction or construction of new facilities. GNGC horizontal pumps with magnetic couplings provide for axial position of the suction pipe and radial position of the delivery pipe. The motor and pump body are mounted on supports (OH 2 according to API 610), the drive shaft of the motor

Our products include Villina-GNGC-2T type centrifugal horizontal pumps with tandem mechanical seals type according to your parameters. These are used for transit in stationary conditions of neutral, corrosive, toxic, as well as explosive and fire hazardous liquids, the vapors of which can form explosive mixtures with air. The units are mainly used by petrochemical industry companies. Parameters of operating fluids (liquids): temperature from -50oС to +400oС viscosity up to 160 cSt density 2,000 kg/m3 max, with a high concentration of particles particle size over 0.2 mm, but not exceeding free passage of the impeller (3 to 12 mm depending on the pump rate) For such conditions, mechanical seals (operating temperature up to 425°C) of well-known companies are used, such as: OOO NPC ANOD, JSC TREM ENGINEERING, UNICHIMTEK Group of Companies and others DESIGN FEATURES The unit consists of a pump, a base plate, an electric motor, a casing and a support system.

Modern petrochemical and gas industries typically use horizontal centrifugal canned pump units with magnetic couplings similar to Villina-GNGC type pumps. They are designed for transiting neutral, corrosive, toxic, as well as explosive and flammable liquids in stationary conditions, the vapors of which can form explosive mixtures with air. Magnetic coupling pumps combine complete tightness, smooth operation, long service life and high maintainability. A sub-type of horizontal pumping units are high-temperature pumps Temperature of the pumped fluid: -50°C to +420°C; viscosity up to 26 cSt; density 2,000 kg/m3 maximum; mass concentration of solid non-abrasive inclusions up to 0.2%; size 0.2 mm maximum Permanent magnets (SmCo) with an operating temperature of up to 450°C are used for operation in these temperature conditions. The pump, a part of the pumping unit, is a single-stage or multi-stage horizontal centrifugal section-type

Centrifugal pumps have well-known advantages such as uniform pumping without surges, the ability to create high pressures at low pump rate in multi-stage designs, long service life and others. However, operation of centrifugal pumps requires building positive pressure (pressure boosting) upstream of the inlet suction pipe for the following reasons: to fill the pump body with the pumped fluid in order to avoid a "dry start" to prevent cavitation during pump operation. Classic methods for creating pressure boosting before centrifugal pumps can be: installation of a tank from which the fluid is pumped, several meters above the axis of the pump shaft and placing the pump in the draw-off sump; inclusion of an additional vacuum pump into the process, which is capable of building the desired pressure boosting of several metres. HOW IS THE PROBLEM OF CREATING A PRESSURE BOOSTING IN MODERN SELF-PRIMING CENTRIFUGAL PUMPS SOLVED? Villina company offers you Villina self-priming GNGC series

Magnetic couplings are used as transmission mechanisms in modern pumps, which makes it possible to obtain a qualitatively new 100% tight device without making essential changes to the design of the electric drive and the wet end of the pump. At present Villina offers GNVC, GNGC and GNVC-P series vertical, horizontal and semi-submersible centrifugal pumps with magnetic couplings, designed for pumping explosive and flammable, toxic and corrosive fluids (petroleum products, alkalis, acids, alcohols, etc). PURPOSE Magnetic couplings for Villina centrifugal pumps allow for transmission of torque from the electric motor to the pump shaft using magnetic fields generated by permanent magnets instead of mechanical engagement devices. At the same time, there is no need to withdraw the shaft from the pump wet end to the drive device, therefore the wet end can be made in the form of a completely sealed system free of leaks which are typical for pumps with mechanical shaft seals.

The design of an electric pump section is similar to the design of a standard vertical electric pump with a GNVC series magnetic coupling, which allows for the use of already proven technical solutions: impeller blades with curved surfaces create an angle of attack and partially allow for switching to the laminar mode of wall-adjacent flow on their surface and provide more efficient deflection of liquid to the periphery; a closed type impeller has a higher efficiency and longer service life compared to open and semi-closed impellers; bell-type fit of the impeller on the pump shaft precisely keeps the geometric position of the impeller with respect to the guide vanes; the vertical position of the shaft resting on a heavy-duty carrying cushion in the vertical plane, and sleeve type bearings in the horizontal plane help prevent sagging of the shaft, as for instance, in the horizontal design of the pump, and play and runout; the use of sleeve type bearings