Lip seals - Import export

iglidur® sealing lip bearing d1 [mm]: Quick and easy-to-mount polymer bushing made of iglidur® J (JDSM) or iglidur® V400 (VDSM) with clip-on radial shaft seal ring as sealing for the rotating shaft. Seals off against dirt, dust as well as all pressure-less media. Polymer bushing with clip-on radial shaft seal ring Sealing for rotating shaft Temperature application range like iglidur® J Coefficient of friction only 10% higher than in iglidur® J Coefficients of friction identically exceptional like iglidur® J Reduced installation space as well as easy and simple mounting Realizable with numerous sealing types High-temperature option VDSM possible Temperatures till 150° C Material: iglidur® J High temperature option VATM, iglidur® V400 Seal ring made of fluorelastomer Bearing-sealing combinations for other applications on request When to use it? When the penetration of dirt and spray water should be prevented When only a small installation space is available in the axial direction When an existing seal should be integrated in a plain bearing When not to use it? When pressurized media should be sealed When absolute impermeability to the shaft and housing is needed continuously We'll gladly do the developing with you iglidur® sealing lip bearing d1 [mm]:

The troubleshooter for energy supply systems in the chip area - available in 4 sizes. Chips and dirt can affect the service life of cables and hoses significantly. With the RX system, igus® offers an extremely tight plastic e-tube that is nonetheless very easy to open. Snap-open in the outer radius A smooth, curved outer contour prevents chips from sticking Injection-molded "sealing lips" all around No holes, cracks, undercuts Series RX40 is IP40 tested (TÜV Saarland) Interior separation and guide trough available Covered pin/hole connection and stops "RBR" version with bending radius on both sides available Typical branches of industry Machine tools All applications in the direct chip sector Applications exposed to dust and dirt General mechanical engineering Dimensions and technical datas RX e-tubes RX32 Inner height hi: 42 mm Inner widths Bi: 80mm Bending radii R: 80 - 250 mm Pitch: 32 mm RX E-Tube RX40 Inner height hi: 52 mm Inner widths Bi: 100 mm bending radii R: 100 - 300 mm Pitch: 40 mm RX E-Tube RX48 Inner height hi: 62 mm Inner widths Bi: 120mm Bending radii R: 120 - 325 mm Pitch: 48 mm RX E-Tube RX56 Inner height hi: 73 mm Inner widths Bi: 140mm Bending radii R: 140 - 350 mm Pitch: 56 mm RX E-Tube RX56 High-temperature plastic version of the chip-proof RX energy tubes from stock - 850°C from 24h RX - from stock against hot chips red dot 2011: honourable mention for RX40 iF-Design-Award for RX e-tubes ESD classification: Electrically conductive ESD/Atex versions on request UL94-V0 classification on request e-tubes available as special design with HT material for 850°C hot chips The troubleshooter for energy supply systems in the chip area - available in 4 sizes. Chips and dirt can affect the service life of cables and hoses significantly. With the RX system, igus® offers an extremely tight plastic e-tube that is nonetheless very easy to open. Snap-open in the outer radius A smooth, curved outer contour prevents chips from sticking Injection-molded "sealing lips" all around No holes, cracks, undercuts Series RX40 is IP40 tested (TÜV Saarland) Interior separation and guide trough available Covered pin/hole connection and stops "RBR" version with bending radius on both sides available Typical branches of industry Machine tools All applications in the direct chip sector Applications exposed to dust and dirt General mechanical engineering Dimensions and technical datas RX e-tubes Chip tests in the igus® laboratory demonstrate the tremendous chip-proof properties of the igus® RX tube. Chip-proof - for all types of chips and applications RX32 Inner height hi: 42 mm Inner widths Bi: 80mm Bending radii R: 80 - 250 mm Pitch: 32 mm RX E-Tube RX40 Inner height hi: 52 mm Inner widths Bi: 100 mm bending radii R: 100 - 300 mm Pitch: 40 mm RX E-Tube RX48 Inner height hi: 62 mm Inner widths Bi: 120mm Bending radii R: 120 - 325 mm Pitch: 48 mm RX E-Tube RX56 Inner height hi: 73 mm Inner widths Bi: 140mm Bending radii R: 140 - 350 mm Pitch: 56 mm RX E-Tube RX56 High-temperature plastic version of the chip-proof RX energy tubes from stock - 850°C from 24h RX - from stock against hot chips Submersion test in water - Various tube types were submerged under water. The new RX tube needs over 30 seconds until it is filled up, thus proving its high leak tightness Y = time in seconds A = igus® products B = competitor Chip penetration test - Various types of tube were exposed to a defined quantity of chips. In the new RX tube, after 80,000 cycles only 0.2 g of chips were found in the interior Y = chip mass [g] A = igus® RX e-tube RX40.100.100 251.900 cycles B = igus® e-tubes 68.10.100.0 256.132 cycles C = test tube 01 250.907 cycles D = test tube 02* 2.600 cycles *Teststop after 2.600 cycles E = igus® products F = competitor E-Chain® selection aids You can find the right E-Chain® quickly by entering concrete parameters and with the aid of a comparison table. Productfinder Assembly instruction Dismantling / assembling a cover, replacing a chain link and assembling / inserting the RX tube. Assembly instruction Configure interior separation Define cables, select chain and configure interior separation. Now also for RX tubes! Interior separation configurator Application examples Applications in various industrial sectors. RX tubes Series RX - new chip-proof design, small pitch, removable cover 1 Chip-proof design without undercuts and edges 2 Excentric locking 3 Material igumid G 4 rounded shape 5 covered pin/hole connection RX tubes IP tested Technical report TÜV NORD red dot 2011: honourable mention for RX40 iF-Design-Award for RX e-tubes ESD classification: Electrically conductive ESD/Atex versions on request UL94-V0 classification on request e-tubes available as special design with HT material for 850°C hot chips

Shower door seals, shower door seal UNIVERSAL LENGTH - Our shower sealing lip is suitable for doors up to 1m in length. Shower door seals, PERFECT FIT - The Vellure shower seal 6mm shower seal is available in 2 sizes. For glass thicknesses of 6mm and 8mm. These therefore fit perfectly and are easy to attach. UNIVERSAL LENGTH - Our shower sealing lip is suitable for doors up to 1m long. It can be easily cut to size and therefore fits perfectly into almost any shower door. Shower cubicle seal. 100% TIGHT - The shower lip seal for shower doors made of high-quality PVC is absolutely tight. Thanks to the pearling effect, the rubber seal optimally repels water from the shower seal glass door. EASY OPENING & CLOSING - Thanks to the soft rubber lip, the shower door opens and closes by itself. The shower lip seal seals a door gap of up to 1.2 cm. QUALITY PROMISE - Our shower seals are absolutely durable and look like new for a very long time. As a German premium

These one-way respirator masks are designed and appropriate for work in dusty environment. This mask consists of several layers filter material, with adjustable aluminium nose bracket, foam rubber pad over the nose, and exhalation valve. It fits perfectly through additional sealing lip, as well as easy adjustable woven elastic bands. Weight only 30g. The dust masks are divided into following classes: FFP1 provides protection against dust and other particles with low health risk For example: fish meal, grain dust, mortar, titanium dioxide, talcum, aluminium FFP2 provides protection against dust and other particles with low health risk For example: ash, concrete, wood dust, oil mist, chalk, quartz, cellulose FFP3 provides protection against harmful, toxic, solid and liquid particles. For example: asbestos, surface treatment, metal foundries, construction works Masks of class FFP1 and FFP2 are availably with and or exhalation valve, for masks of class FFP3 exhalation valve is...