Clip - Import export

Solutions for plates Application examples - Automotive The new solution for all applications in stamped sheet metal retainers: iglidur® Clip On's are frequently used in seat and convertible top systems and multi-joint hinges. iglidur® clip-on bearings facilitate captive assembly even in punched sheetmetal / steering arms with limited fine blanking content. Compensation of axial clearance Loss secure pre-assembly possible Electrically conductive materials are optionally available Pressure-resistant materials until 80 MPa The Clip On bearings can also be produced from electrically conducting iglidur® RN89, thus permitting e-coating.

iglidur® clip bearing, metric d1 [mm]: iglidur® clip bearing, inch d1 [inch]: iglidur® clip bearings are especially intended for the shaft bushing through plates. For this reason the bearing has a flange on each of the two front sides. After the clip-on the bearings are secured on both sides in the plate. The clip bearings have chamfered slot on the side that enables the mounting of the bearing on one side. After the mounting the bearing straddles and lines the bore in the plate. The shaft prevents the clip bearing from slipping out of the bore. The bearing cannot slip out of the bore even in axial movements. Extremely simple mounting through lateral slot Maintenance-free and self-lubricating Good flexibility in punch hole Good abrasion resistance Quiet operation Suitable for rotary and linear movements Extendibility through the slot Undetachable through double flange Special dimensions possible Plate thicknesses from 3 mm to 4 mm available from stock Material: iglidur® M250 Special properties of the iglidur® clip bearings iglidur® clip bearings are made from the most abrasion-resistant material, iglidur® M250. iglidur® M250 is a bearing material for rugged, wear-resistant bearing systems for medium loads. The bearings are self-lubricating and can be used dry. If required the bearings can also be lubricated. The material iglidur® M250 is resistant to all common lubricants. The iglidur® clip bearings are the ideal solution for bearing functions with low loads. The easy mounting makes it ideal for applications with difficult bearing locations. Compressive strength The permitted static surface pressure of iglidur® M250 amounts to 20 MPa at room temperature. Due to the good adaptability to uneven surfaces of the bearing housing, a high pressure load capacity of the clip bearings persists even in punched holes. For the most small bearing surfaces, the good vibration dampening properties and the insensitivity to misalignment are of primary importance. Surface speeds Clip bearings are particularly wear resistant in slow rotating, oscillating and axial motions. You can find the maximum gliding speeds for the various motions for the iglidur® M250 material under the materials data link shown below. A lubrication at installation or continuous lubrication raises the permitted surface speeds. Clip bearings are available from stock in dimensions of 3 to 25 mm. Fixation Triflex RS For mounting, the bearings are laterally pressed together with the large flange. The chamfered slot makes the bearing spiral-shaped, whereby it can be easily inserted in the plate. The remaining slot in the attached clip bearing can compensate for linear expansions of the circumference. Thus narrow bearing clearances are possible with clip bearings. The bearing clearance is dimensioned in such a way that in a housing bore with a nominal diameter, a shaft made with the same nominal diameter turns easily. The clip bearing can be used in H-tolerance housings up to H13. The turning of the clip bearing in the bore is also permitted. Operating temperatures The wear resistance of the iglidur® clip bearings are excellent with operating temperatures till 80°C. Even at low temperature the bearings remain elastic and abrasion resistant. When to use it? When a sheet metal feedthrough is required When the bearing should be captively clipped on in a drill hole with rough tolerance For rotating, linear and pivoting movements When a quick-mounting bearing solution is sought Clip bearings application examples When not to use it? When constant temperatures of more than +80°C occur iglidur® G When a high-precision bearing is needed iglidur® J When the housing bore is more than 4 mm long iglidur® Clips 2 iglidur® MKM When very high surface pressures occur iglidur® G iglidur® clip bearing, metric d1 [mm]: iglidur® clip bearing, inch d1 [inch]:

MDM Double flange bearing b1 [mm]: When to use it? When the axial safety of the iglidur® clip bearing is not sufficient When there is a housing with very rough tolerance When high axial forces must be absorbed When not to use it? When an automated assembly is required iglidur® MKM When the iglidur® clip bearings offer adequate tightness iglidur® clip bearing When a large guide length is necessary iglidur® MKM MDM Double flange bearing b1 [mm]: Special features Large flange surfaces Symmetrical flange Easy installation Easy to clip on Undetachable after cataphoretic painting process Special option possible

Simplex-, Duplex-clamps, wire rope clips, various turnbuckles, thimbles made from stainless steel

Wire rope clip similar DIN 741 Simplex-, Duplex-clamps, wire rope clips, egg shaoed wire rope clips, varous turnbuckles,thimbles, rope shortenings made from steel and ferrules made from aluminium

In our range we have a variety of different rubberised floor plates which can be used for earthmoving machines with a total weight of up to 25 tonnes. The rubberised floor pads (ChainOn) can be mounted directly on the carrier chain. You will also find bolton pads (BoltOn) and clipon pads (ClipOn), which only need to be fixed to the steel floor plates. We also have vulcanised rubber and polyurethane floor pads in our range. Pads for standard applications up to 25 tonnes are also part of the portfolio. In addition, we have rubberised floor plates as well as attachments for all types of asphalt machines from Caterpillar, Vogele, Wirtgen, Dynapac, Marini, Abg, Bitelli and many other brands in our range.

For marking Euro pallets Dimensions: 100 x 75 x 150 mm For Labels sized DIN A7 / DIN A8 Material: PP

Ø = mounting hole diameter S = max. sheet thickness Material: PA 6.6 Colours: last digits 500 = white last digits 599 = black Note: The order quantity refers to the connections. e.g. order quantity = 500 pcs., you get 500 clips & 500 counter pieces --> 500 connections

Our Identification Accessories such as Lanyards, Card holders and Clips are available in different sizes and colours.

A Nose clip avoids breath loss through the nose during sampling.