Switch installation - Import export

■ Configurable output signal (4...20 mA, 0...20 mA, 0...5 V, 0...10 V, ±5 V, ±10 V) ■ DIN rail mounting ■ Low residual noise ■ Built-in cable break detection with alarm-output

For conductive limit level switches DIN rail installation, width 50 mm 1x Pt100 & 4x measurement input Output: 3x relay, 2x PNP/NPN

For conductive limit level switches DIN rail installation, width 22.5 2x measurement input Output: 2 x relay

Anywhere small quantities of wastewater need to overcome a high discharge head is the perfect application for the flattened version of the AWALIFT 2/2, with a shape that makes it a good space-saving option. It also offers our proven bulk materials collection system and is installed dry. The system controls are individually adjusted and installed in a switch cabinet outside of the shaft. Draining small towns with up to about 1700 residents which cannot be drained using natural gradient or as an intermediate pumping station within the context of a pressure drainage system Residential and industrial areas Towns Communities Infrastructure facilities such as airports, industrial parks, underground stations etc. Product features One holding tank with two separator systems Two centrifugal pumps and motors according to type and operating location required Four pump gate valves Two STRATE non-return valves Two pressure pipe gate valves DN 100 One Y-pipe DN 100

The IF2035 interface modules are designed for easy connection of Micro-Epsilon sensors to Industrial Ethernet controllers, e.g., plant control systems. The PROFINET and EthernetIP modules are compatible with sensors that output data via an RS422 or RS485 interface. These modules operate on the sensor side with up to 4 MBaud and have two network connections for different network topologies. Installation in switching cabinets is via a DIN rail.

With very slim dimensions and overall IP67 protection, the I49 switches are a perfect solution for either position indication or safety applications. — Flat design — Highly flexible deployment — Reliability — Simple and quick installation — Compact IP67 switch for safety applications

The aluminium pressure die-cast protective shroud (F3: aluminium sand casting) fully shields the pedal at the top and sides while the wide base provides a high degree of stability. It reliably prevents accidental operation from above by falling objects or careless operation from the side. Due to its robust construction the protective shroud withstands a drop of 20 kg from a height of 1 m. The foot switch is uniquely designed to allow inclusion of additional equipment: — Emergency Stop button — Contactor on DIN rail as main power switch — Customized installations (e.g. light indicators)

For preassembled cables and simple maintenance PFLITSCH brought the first completely splittable plastic single cable gland to the market in the form of the UNI Split Gland. This product allows preassembled cable to be fed through a hole or the replacement of old or defective cable glands, without having to interfere with the existing cable installation or switch off the affected machine. Your advantages: Split cable gland body, pressure screw and counter nut in size M20, M25 and M32 for over 100 different sealing inserts For cable cross sections of 2.0 mm to 20.5 mm Ingress protection rating IP 67 Superior strain relief values to EN 62444 class A Ambient temperatures of -20 °C to +80 °C

Shapely multiple socket with comfortable external hand/foot switch. Robust and shapely hand/foot switch with a very flexible 1.5 m control line. A RJ-11 connection makes switch pluggable and extendable, which enables for a very easy and flexible installation. Switching status display on hand/foot switch. With option to wind the cable around the rail for storage. With practical hanging facility. Earthed sockets in a 45° arrangement, ideal for angular plugs. Childproof sockets. Packaging: with banderole. Description: CSP 06 Cable length: 3 m Cable: H05VV-F 3G1,5 Length approx.: 51,5 cm Socket: 6 switchable Colour: Black/Light Grey Plug-in system: DE

regulated 24 pin DIL-grid PI-input filter Efficiency factor up to 50% Operating temperature up to +71°C Electrically isolated 500VDC min. Option H: 3kV Optional: For installation in switch cabinet for screwing or clipping into place on TS35-rail as per EN60715 Optional: SMD-Version when ordering addition SMD or article number/SMD

• Seat principle, direct actuated; • Frictionless movement Spider µProp-valves are real proportional valves, in which the armature stroke is proportionally defined by the infinitely-variable current applied. The constant ratio between armature stroke and flow rate thus allows variation of the flow rate by way of the applied current. Spider µProp-valves are like Spider on/off valves microvalves The anchors installed in the micro valves have the shape of a disk. In energized status, this so-called flat armature is pulled against the magnetic yoke component group. If the coil is deactivated, the leaf spring joined to the flat armature presses the seal positioned on the spring-armature assembly unit against the valve seat. These quick-acting valves owing to the small mass of the installed armature achieve switching phases in the millisecond range. These valves have a capacity of up to 4 billion actuations, depending upon operation mode.

• Sizes: Ø 7 mm, Ø 15 mm, Ø 21 mm; • Application: Neutral and mildly aggressive liquids, gases and vapors; • direct actuated; • 2-way valves and 3-way valves, NC; Spider valves are allocated to the micro valve category (outside diameter 7 mm). The anchors installed in the micronized valves have the shape of a disk. In energized status, this so-called flat armature is pulled against the magnetic yoke component group. If the coil is deactivated, the leaf spring joined to the flat armature presses the seal positioned on the spring-armature assembly unit against the valve seat. These quick-acting valves owing to the small mass of the installed armature achieve switching phases in the millisecond range. As these valves predominantly featuring cartridge connections have an almost frictionless armature movement, they have a capacity of up to 4 billion actuations, depending upon operation mode. Spider valves may also be triggered via so-called pulse width modulation.

– Connection cable 4 meters with plug – Sieve installed in the water inlet – Bypass incl. Pressure gauge installed in the device – Float switch installed for low water alarm – MicroGroove condenser (micro-channel filter, as sensitive to dirt) Terminal– Evaporator: copper plain tube coil – A series for min. outlet temperature of -5 ° C. – Many possible configurable and already assembled e.g. overflow protection – Made in Germany!

This rail guided vehicle system MONOFLEX is powered by inductive energy. The smart track guided vehicles run on floor mounted twin rails. The MONOFLEX system sets new standards in terms of throughput, flexibility, and scalability. True to the motto “dynamic warehousing”, this rail guided vehicle system from DAMBACH Lagersysteme provides a high-performance conveying system for the apron in warehouse systems, or functions as an alternative to conveyor systems with continuous conveyors. For example, the MONOFLEX can form the ideal complement to the MULTIFLEX pallet shuttle system. This rail guided vehicle system from DAMBACH consists of high-performance transport carts and a twin rail track. The track is made from anodized aluminum, which is not only robust, but easy to install. Simple switches ensure good availability, even in the case of complex plant layouts. With a 1:1 distribution of the material flow

In addition to the strip speed, VRecoS also records up to three further tracks, such as the rolling force or the strip thickness at the ingoing and outgoing ends of the mill. The measurement protocols can be stored, printed out and distributed by e-mail. The measured values are recorded as a function of length. The recording frequency can be set with a scanning rate of 2 ms. Random lengths of strip at the leading and trailing ends (drop-off) can be suppressed, even subsequently. The signals are recorded using a data collector belonging to the scope of supply. Its electronics with input and output modules is designed for installation in switch cabinets or desks in interference-proof 24 Volt top-hat (DIN) rail technology. It transmits the data via a network cable to the Windows recording computer which can be supplied by Vollmer or by the customer.