Magnetic%20equipment - Import export

Pole extensions are the perfect complement to the square pole magnetic clamping plates and modules. Workpieces with any structure can be perfectly clamped with Assfalg pole extensions. The pole extensions adjust optimally to the shape of the workpiece. The workpiece is underpinned and is located safely on the extensions,, for a five-side complete processing free of vibration and warping. The surface of the magnetic clamping plate is additionally protected against accidental damage through, for example, deep drilling. Another possible application is use as a stop for 3D forms, round material and smaller workpieces. Other pole extension or pole placement plates are available on request. The connection cables are available in different lengths. They connect the magnetic modules with each other in a row. The controller is additionally connected with the magnetic module through this. The cables are protected against hot chips and cooling water.

The uniform radial pole division offers significant advantages compared to magnetic chucks with parallel pole or square pole division in particular when processing rings and discs that are difficult to hold as well as sleeves. A higher stability and stiffness can be achieved through radial pole division in particular with larger diameters. A centric through-hole can be incorporated in the area that has no active magnet. The electropermanent magnetic chuck EPMradial from Assfalg is ideal for clamping big, rotationally-symmetrical workpieces (for example, bearing ring processing) starting at a diameter of 400 mm, in particular on rotating and milling machines as well as drilling machines without distortion. The EPMradial electropermanent magnetic chuck permits an extreme takeoff during the hard processing of rings. The highest precision is achieved during grinding work.

The EPFlux magnetic clamping plate has no remanence (residual magnetism) upon deactivation. Highly alloyed and hardened workpieces can be easily loosened from the magnetic clamping plate. Highest grinding precision is achieved, because the plate is not heated up. Not heated up means that there are no expansion and deformation to the workpieces to be processed. The electropermanent magnetic clamping plate is the ideal clamping plate for precision grinding machines. The laminated surface made of brass and steel and the solid steel body guarantee magnetic holding force as well as unique hardness over the entire surface. With the EPFlux magnetic clamping plate, large and small workpieces can be evenly clamped. The magnetizing and demagnetizing occurs through a short power pulse within seconds.

The patented EPM magnetic clamping plates *** Patent-No. EP1874504 *** have a solid steel surface and are therefore significantly more resistant than conventional plates with epoxy resin against hot chips, coolant and other processing influences. The workpiece is clamped on the EPM magnetic clamping plate MAGNASLOT within seconds through an impulse current. This combo plate allows for 5-side processing of your workpieces in only one clamp. This reduces equipping times to a minimum and increases productivity. Conventional machine vices or clamping claws can be used to clamp non-ferrous workpieces. Through the use of pole extensions, which adjust to the workpiece surface, any unevenness on the workpiece can be compensated for and a deformation of the workpiece can be prevented. The magnet field from the MAGNASLOT magnetic clamping plate guarantees low-vibration clamping of your workpieces.

The patented EPM magnetic clamping plates *** Patent-No. EP1874504 *** have a solid steel surface and are therefore significantly more resistant than conventional plates with epoxy resin against hot chips, coolant and other processing influences. The workpiece is clamped on the EPM magnetic clamping plate MAGNASLOT within seconds through an impulse current. This magnetic clamping plate allows for 5-side processing of your workpieces in only one clamp. This reduces equipping times to a minimum and increases productivity. Through the use of pole extensions, which adjust to the workpiece surface, any unevenness on the workpiece can be compensated for and a deformation of the workpiece can be prevented. The magnet field from the MAGNASLOT magnetic clamping plate guarantees low-vibration clamping of your workpieces. This protects the milling spindle as well as your tools, increases process safety and extends the service life.

The patented EPM magnetic clamping plates *** Patent-No. EP1874504 *** have a solid steel surface and are therefore significantly more resistant than conventional plates with epoxy resin against hot chips, coolant and other processing influences. The workpiece is clamped on the EPM magnetic clamping plate MAGNASLOT within seconds through an impulse current. This magnetic clamping plate allows for 5-side processing of your workpieces in only one clamp. This reduces equipping times to a minimum and increases productivity. Through the use of pole extensions, which adjust to the workpiece surface, any unevenness on the workpiece can be compensated for and a deformation of the workpiece can be prevented. The magnet field from the MAGNASLOT magnetic clamping plate guarantees low-vibration clamping of your workpieces. This protects the milling spindle as well as your tools, increases process safety and extends the service life.

The Assfalg Battery Electro-Permanent Lifting Magnetic Beam EPMBL has a compact design. Due to the integrated rechargeable battery box, a power connection is no longer required. The EPM Battery Magnetic Lifting Beam is operated by remote control. The load lifting beam with a max. load of 1,500 kg is equipped with magnetic modules and can thus safely move sheet metal formats from a minimum length of 500 mm to a maximum length of 4,000 mm.

These highly accurate Magnet Sinetables are used for grinding work as well as for eroding. It allows for universal clamping of small, medium and large workpieces of any thickness, however, they are best suitable for thin and fine workpieces. The permanent Microsine magnetic clamping plate is preferably used if a flat and light construction is needed during grinding, eroding or milling. A complete, fine transverse pole distribution (steel/brass) guarantees a consistent holding force over the entire width up to the longitudinal sides. This clamping plate can be activated through a hexagonal switch lever. They are available in two versions: either single-pivotable via the longitudinal axis or double-pivotable via the longitudinal and transverse axis. Gauge blocks can be used to set the tilt angle precisely up to 45 °. The magnet Sinetable is suitable for accurate grinding of workpieces with nonparallel surfaces. Individual designs can be created on request.

These magnets can be individually adjusted to different tasks. They are only switched on with a short compressed air impulse between 5 and 8 bar. They are low-maintenance and have very fast switch-on times. Individual solutions with multiple parallel-controlled magnets simplify your lifting task or work process. It is not just used in fully automatic systems, but rather also for the simples manual lifting processes.

The AR series was specifically designed for workpieces that do not have any level contact surfaces. They are only switched on or off with a short compressed air impulse. Workpieces with level, flat, round or irregular surfaces are transported without effort. Individual solutions with multiple parallel-controlled magnets simplify your lifting task or work process. The magnets are only switched on with a short compressed air impulse between 5 and 8 bar. They are low-maintenance and have very fast switch-on times. It is not just used in fully automatic systems, but rather also for the simples manual lifting processes.

These magnets can be individually adjusted to different tasks. They are only switched on with a short compressed air impulse between 5 and 8 bar. They are low-maintenance and have very fast switch-on times. Individual solutions with multiple parallel-controlled magnets simplify your lifting task or work process. It is not just used in fully automatic systems, but rather also for the simples manual lifting processes.

These magnets can be individually adjusted to different tasks. They are only switched on with a short compressed air impulse between 5 and 8 bar. They are low-maintenance and have very fast switch-on times. Individual solutions with multiple parallel-controlled magnets simplify your lifting task or work process. It is not just used in fully automatic systems, but rather also for the simples manual lifting processes.

The positioning drawbar has a gradual flexible range of +/- 60°. The adjustment occurs easily by loosening the hand brake. A wireless remote control can be installed directly on the handle to switch the magnets on and off. Other remote controls to control cranes are possible on request. All technical data can be found in the .pdf file.

Funnel stand with two funnel holders and two reducing inserts. Space-saving design with two practical storage areas. Sturdy and stable funnel stand, resistant to chemicals, shatter-proof and with continuously variable height adjustment. The funnel stand is suitable for all funnels from 40 to 180 mm in diameter. The funnel holders can be used with reducing inserts for small funnels. The funnel stand also makes an excellent filtering stand. Thanks to an innovative magnet concept no clamping screws are necessary. The height of the funnel holder can be adjusted easily and flexibly with one hand. The laboratory stand can be flexibly adapted with corresponding accessories, for example with adjustment funnel holders or a holder for Imhoff funnels. The funnel stand can also be converted into a pipette stand.

The stand for sedimentation funnels is used to keep, hold or store Imhoff funnels safely and reliably during sedimentation. Two funnel holders ensure that Imhoff funnels will be held safely and securely and can be placed in an absolutely vertical position. Stand with two holders for sedimentation funnels, suitable for funnels 90 mm or more in diameter. Thanks to an innovative magnet concept no clamping screws are necessary. The height of the funnel holder can be adjusted easily and flexibly with one hand. With the corresponding accessory the holders for Imhoff funnels can also be replaced by holders for all-purpose funnels.

Frame for pipettes with two rotating perforated plates and drip pan. The holders are suitable for up to 40 pipettes of different sizes, for all measuring and full pipettes up to a max. diameter of 18 mm.A drip pan protects the tips of the pipettes and collects liquid as it drips off.The pipette stand is suitable for drying and for space-saving storage of pipettes or thermometers, test tubes and similar items. A very sturdy pedestal ensures absolute safety against overturning.No clamping screws are necessary thanks to an innovative magnet concept. The height of the holding plates can be adjusted easily and flexibly with one hand. The lab frame can be flexibly adapted with corresponding accessories, for example as a frame for Imhoff sedimentation funnels or as a funnel frame.

Battery-powered load lifting magnets are location-independent and flexible like permanent load lifting magnets and at the same time have the advantage of remote controllability and operability at the push of a button. They are mainly used where larger loads are continuously handled, as they can be switched without physical effort. Another common application is where access to the touchdown point is difficult. All our battery-powered lifting magnets are equipped with an IR remote control and a high-quality, deep discharge-proof gel battery. FBM load lifting magnets comply with the latest standard and have been designed according to the main criteria of safety and ease of use.

FXE-T2500/50 and 4000/80 electro-permanent lifting magnet trusses in compact design with onBoard control technology are designed for frequent handling of larger formats. Like FXE lifting magnets, they can be operated directly from mains voltage and are therefore very quickly installed and ready for use. They can be controlled directly on the unit or optionally via remote control. The FXE-T6400/80 electro-permanent lifting magnet truss is a fully equipped standard unit with all options. The truss with 6400 kg max. lifting capacity is equipped with sliding magnetic modules and can thus safely move sheet metal formats from min. 1200mm length to max. 6000mm length.

FXE electro-permanent lifting magnets are equipped with on-board control technology for direct connection to mains voltage - the fast, user-friendly plug & play solution for loads from light to super heavy. Different pole types are available, depending on the material thickness and surface to be moved.