International transport - Import export

Muscular and skeletal problems are the most common reasons for people being unable to work, particularly if they have a job that frequently involves physically strenuous activity like pushing and pulling loads. The electric drive systems of the Blickle ErgoMove® series reduce these health risks considerably. The effort required for pulling and pushing is reduced by up to 100 %. The physical strain on the operator is decreased during internal material transport due to the considerably lower amount of effort required compared with manual operation. Equipment and transport units of any kind can be quickly and easily upgraded with a “plug & play” electric drive, steering and braking assistance. The modular sets include two fixed castors with electric drive, cockpit solutions with integrated controls and battery unit as well as all relevant safety features.

The manual magnet transporter magnetizes and demagnetizes with the push of a button. Nevertheless, it holds like a permanent magnet. Oily, sharp workpieces or hot burn cutting parts can be quickly moved with this. The HL 60-CEL has an ergonomic extended handle bar to pick up components on the ground. It is switched through a remote control in the handle. All technical data can be found in the .pdf file.

These magnets can be individually adjusted to different tasks. They are only switched on with a short compressed air impulse between 5 and 8 bar. They are low-maintenance and have very fast switch-on times. Individual solutions with multiple parallel-controlled magnets simplify your lifting task or work process. It is not just used in fully automatic systems, but rather also for the simples manual lifting processes.

The AY series was developed specifically for sheet handling. They can measure technically with vacuum systems in the thin sheet area and are much more efficient. They are only switched on with a short compressed air impulse between 5 and 8 bar. They are low-maintenance and have very fast switch-on times. Individual solutions with multiple parallel-controlled magnets simplify your lifting task or work process. It is not just used in fully automatic systems, but rather also for the simples manual lifting processes.

These magnets can be individually adjusted to different tasks. They are only switched on with a short compressed air impulse between 5 and 8 bar. They are low-maintenance and have very fast switch-on times. Individual solutions with multiple parallel-controlled magnets simplify your lifting task or work process. It is not just used in fully automatic systems, but rather also for the simples manual lifting processes.

The EPM M electropermanent load lifting magnets are used where there is a frequent change of workpieces due to the very short switching times. Only a 230V rated current, depending on magnet with 230V or 400V, must be provided to use these devices and they are then immediately ready for use. Through electrical impulses within seconds, the EPMM from ASSFALG is automatically switched on or manually with the push of a button. No electricity flows during load transport and nevertheless, the workpiece is as securely clamped as with a permanent load lifting magnet. The electropermanent battery lifting magnet EPMM can be used in single mode as well as on magnet traverses and is an interesting alternative for 3-shift operation. With the tip function (inching), even stacked sheets can be separated starting with a thickness of 4 mm.

The electropermanent load lifting magnets from the EMPH series are suitable for the lifting and transportation of individual slabs and unprocessed blocks. These magnets are used to handle loads with a large air gap or with scaled surface. Only a 400V rated current must be provided to use these devices and they are then immediately ready for use. Through short electrical impulses within seconds, the EPMH from ASSFALG are automatically switched on or manually with the push of a button. No electricity flows during load transport and nevertheless, the workpiece is as securely clamped as with a permanent load lifting magnet. Through the impulse current control, the EPMH load lifting magnets do not use much energy. The effectiveness and efficiency can be seen on the one hand in the reduction of operating costs and on the other hand in a saving of time.

The SB950-SF is equipped with the highest safety technology. The electropermanent battery lifting magnet SB950-SF is the top product from ASSFALG in the 950kg load range for flat material. 400kg can be lifted for round material. The SB950-SF has an installed sensor. It measures the magnetic force, compares it with the workpiece weight and shows on the display if the workpiece can be transported. Parameters such as surface property, material thickness and material are considered here. They combine the advantages of permanent load lifting magnets with those from electro load lifting magnets. Through electrical impulses within seconds, the electropermanent battery lifting magnet SB950-SF from ASSFALG can be automatically or manually switched with the push of a button. Even though no electricity is present during the load transportation, the workpiece is clamped as securely as it would be with permanent load lifting magnets.

The electropermanent battery lifting magnet SBs are top products from ASSFALG in the 200kg | 500kg | 950kg load range for flat material. Round material can be lifted with up to 50kg | 200kg | 400kg. They combine the advantages of permanent load lifting magnets with those from electro load lifting magnets. Through electrical impulses within seconds, the electropermanent battery lifting magnets SB200 | SB500 | SB950 from ASSFALG can be automatically or manually switched with the push of a button. Even though no electricity is present during the load transportation, the workpiece is clamped as securely as it would be with permanent load lifting magnets. Approximately 1,000 ON/OFF switch cycles are possible until the integrated batteries must be recharged through a simple power connection. The electropermanent battery lifting magnets SB200 | SB500 | SB950 can be used in single mode as well as on magnet traverses and is an interesting alternative for 3-shift operation.

The manual magnet transporter HL-series are ideal wherever conventional load lifting magnets are not used due to the low material thickness. They can be used to transport sheets vertically or horizontally directly from the sheet shelf directly to the workplace or on a transportation vehicle. They are used for the secure transportation of sharp steel sheets in sheet storage, burn cutting operations and stamping. All technical data can be found in the .pdf file.

For decades, the crane magnetic transporters from the SH series have been used throughout Europe as the optimal solution for the crane transportation of sheets, even with larger sizes. Contrary to normal load lifting magnets, crane magnet transporters have a flatter magnetic field allowing them to take up thinner workpieces such as sheets already from 3 mm thickness. They are ideal for horizontal and vertical transport and extremely efficient, but they must be separated from the workpiece using a jacking fixture. With bend presses, they are an interesting alternative to mechanical carrying clamps for metal sheet guiding. The mobile crane suspension makes it possible to lift and move heavy metal sheets. The SH series is used where sheets have to be lifted, transported and moved with a crane, for example, in a material warehouse.

The manually activated permanent load lifting magnets with flexible single or double hooks are ideal for the horizontal and vertical transportation of materials. A wide range of models of the Mlay lifting magnets are available with bearing loads between 90 kg and 1825 kg for different material thicknesses. The flat magnet field is another advantage when destacking sheets or workpieces. Replaceable pole shoes make individual solutions possible. They can transport, for example, angle profiles or round sticks with different dimensions.

The unmistakable advantages of the load lifting magnets Elift from Assfalg are economy and fast handling. The hand-operated permanent load lifting magnet is the perfect and fully developed solution for moving all ferromagnetic materials in an efficient, safe and reliable way. Usage during lifting and transportation includes a variety of flat and round workpieces, from pre-processed materials to raw material. A wide range of models of the Elift lifting magnets are available with bearing loads between 100 kg and 5000 kg for different material thicknesses. The Elift has become an irreplaceable helper in many areas of application. ASSFALG offers an additional ring eyelet for the Elift 300 and Elift 500 allowing vertical transportation. We would be happy to perform an annual safety inspection of your magnets. All technical data can be found in the .pdf file.

The manual magnet transporters SH 12, from German production, are ideal wherever conventional load lifting magnets are not used due to the low material thickness. They can be used to transport sheets vertically or horizontally directly from the sheet shelf directly to the workplace or on a transportation vehicle. They are used for the secure transportation of sharp steel sheets in sheet storage, burn cutting operations and stamping. All technical data can be found in the .pdf file.

The EPMB electropermanent battery lifting magnets are considered the best load lifting magnet development in the past decades at ASSFALG. They combine the advantages of permanent load lifting magnets with those from electro load lifting magnets. Through electrical impulses within seconds, the EPMB from ASSFALG is automatically switched on or manually with the push of a button. No electricity flows during load transport and nevertheless, the workpiece is as securely clamped as with a permanent load lifting magnet. The electropermanent battery lifting magnet EPMB can be used in single mode as well as on magnet traverses and is an interesting alternative for 3-shift operation. With the tip function (inching), even stacked sheets can be separated starting with a thickness of 6 mm. All technical data can be found in the .pdf file.

The electropermanent load lifting magnet traverses TBK4 and TBK6 with automatic telescopic arm allow the lifting and transportation of sheets in different sizes from 3m to 16m. The patented solid steel modules are more heat-resistant than comparable modules made with a plastic casting mass. Only a 400V rated current must be provided to use these devices and they are then immediately ready for use. Through short electrical impulses within seconds, the magnet traverses from ASSFALG are automatically switched on or manually with the push of a button. No electricity flows during load transport and nevertheless, the workpiece is as securely clamped as with a permanent load lifting magnet. With the tip function (inching), even stacked sheets can be separated starting with a thickness of 5 mm. Magnet modules that are not needed can be switched off with the multi-channel control. This means a large magnet traverse system can be securely used for the transportation of smaller sheets.

These magnets can be individually adjusted to different tasks. They are only switched on with a short compressed air impulse between 5 and 8 bar. They are low-maintenance and have very fast switch-on times. Individual solutions with multiple parallel-controlled magnets simplify your lifting task or work process. It is not just used in fully automatic systems, but rather also for the simples manual lifting processes.