Distance measurement - Import export

Wire-actuated encoder with a freely programmable electronic digital display. Linear distance measurement up to 1000 mm. Long battery life. Easy battery change without dismantling of the device. LCD display with 5 digits and special characters. Digit height approx. 8 mm. Flexible mounting position. Easy mounting.

Miniature wire-actuated encoder designed to capture linear measurement distances. Its measuring length of 600 mm is very long considering its small size. SG5 is universally usable thanks to its standardized interfaces.  Very small design. Universally applicable thanks to standardized interfaces. Easy mounting. Measurement lengths up to max. 600 mm. Potentiometer, voltage or power output. Housing made of reinforced plastic.

Absolute, sensor for MA505 and MA561 Profile MSA: To be connected to magnetic displays MA505 and MA561 Max. resolution depends on downstream electronics unit Repeat accuracy depends on downstream electronics unit ≤1 mm reading distance Max. measuring length 5120 mm

Max. resolution of 5 μm absolute, 1 μm incremental. Repeat accuracy of 0.005 mm. SSI, RS485, CANopen output circuits. Additional incremental signals LD as an option (SSI, RS485). Reading distance ≤1.3 mm. Max. measuring length 10240 mm. Status LEDs for diagnosis.

Extremely resistant to external influences. Solid or blind-hole hollow shaft, max. Ø 20 mm. Adaptation to various measurement distances owing to a wide range of gear ratios. Integrated slip clutch to protect the potentiometer. Potentiometer or power output. IP65 protection category. Up to 3 cam-operated switch outputs, freely adjustable.

Compact design with through hollow shaft Profile GP02: Through hollow shaft Ø 14 mm Adaptation to various measurement distances owing to a wide range of gear ratios Compact, low-cost design Potentiometer or power output Easy mounting

With solid or blind hole shaft Profile GP04/1: Extremely resistant to external influences Solid or blind-hole hollow shaft, max. Ø 20 mm Adaptation to various measurement distances owing to a wide range of gear ratios Integrated slip clutch to protect the potentiometer Potentiometer, power or voltage output IP65 protection category

Robust housing with through hollow shaft Profile GP09: and fine reading Through hollow shafts up to ø20 mm Adaptation to various measurement distances owing to a wide range of gear ratios Integrated slip clutch to protect the potentiometer Compact design Potentiometer, power or voltage output IP68 protection category with oil filling possible Easy mounting

Potentiometric displacement sensors are used for direct, precise measurement of mechanical displacements. The mechanical parts of the measuring equipment must be set-up in such a way that the sliding shaft can move without play or lateral forces. A special multi-finger slider ensures good contact even when the adjustment speed is high or in the presence of vibration. With its housing diameter of only 12.7 mm, the model 8709 is also suitable for highly compact structures. The movable fastening clamps allow the user variable options for attaching the sensor without complication. Optionally available adaptations, such as flange and ball joint versions, extend and complement the range of possible applications. Typical fields of application include: Measuring the stroke on riveting machines Measuring insertion distances Offset measurements on bearings Spring travel measurements on axes Measurements of the movement of hoisting platforms Length measurements on pipe bending machines

Through hollow shaft Ø 14 mm. Adaptation to various measurement distances owing to a wide range of gear ratios. Compact, low-cost design. Potentiometer or power output. Easy mounting.

Wire-actuated encoder with redundant acquisition of linear measuring distances with a maximum measurement length of 4000 mm. Robust design. Measuring lengths up to 4000 mm. Analogue signal output in redundant design (2x 4…20 mA or potentiometer). Variable mounting options. Lockable vent and water drain holes. Very robust measuring rope (stainless steel). IP65 protection category. M12 plug connection.

Solid shaft Ø 4 mm or Ø 6 mm. Adaptation to various measurement distances owing to a wide range of gear ratios. Integrated slip clutch to protect the potentiometer. Compact design. Potentiometer, power or voltage output. IP65 protection category.

Extremely resistant to external influences. Solid or blind-hole hollow shaft, max. Ø 20 mm. Adaptation to various measurement distances owing to a wide range of gear ratios. Integrated slip clutch to protect the potentiometer. Potentiometer, power or voltage output. IP65 protection category.

Solid shaft Ø 6 mm. Adaptation to various measurement distances owing to a wide range of gear ratios. Integrated slip clutch to protect the potentiometer. Compact design. Potentiometer or power output. IP65 protection category. Up to 3 cam-operated switch outputs, freely adjustable.

And fine reading. Through hollow shafts up to ø20 mm. Adaptation to various measurement distances owing to a wide range of gear ratios. Integrated slip clutch to protect the potentiometer. Compact design. Potentiometer, power or voltage output. IP68 protection category with oil filling possible. Easy mounting.

Compact design with solid shaft Profile GP03/1: Solid shaft Ø 4 mm or Ø 6 mm Adaptation to various measurement distances owing to a wide range of gear ratios Integrated slip clutch to protect the potentiometer Compact design Potentiometer, power or voltage output IP65 protection category

Profile GP44: Extremely resistant to external influences Solid or blind-hole hollow shaft, max. Ø 20 mm Adaptation to various measurement distances owing to a wide range of gear ratios Integrated slip clutch to protect the potentiometer Potentiometer or power output IP65 protection category Up to 3 cam-operated switch outputs, freely adjustable

To be connected to magnetic displays MA505 and MA561. Max. resolution depends on downstream electronics unit. Repeat accuracy depends on downstream electronics unit. Reading distance ≤1 mm. Max. measuring length 5120 mm.

Max. resolution 10 μm. Repeat accuracy 0.01 mm. SSI, RS485 output circuits. Reading distance ≤2 mm. Max. measuring length 20480 mm.

Display accuracy max. 10 μm. Repeat accuracy max. ±0.01 mm. Lowest-power LCD. Reading distance ≤2 mm. Incremental measurement and reset function. Direct reference/offset value input. Hard-wired sensor.

Due to their extremely compact design, these load cells can be used wherever static or dynamic load forces have to be measured in very tight spaces. Model 8416 is perfect for use in micro-technology and just as suitable for measuring tasks in the research and development sector. The ultra-miniature compression load cell model 8416 is a flat, circular disc, the bottom of which is sealed with a cover. The load application button for receiving the compression forces is an integrated part of the sensor. The sensor element inside the body carries a strain gage full bridge which outputs voltage directly proportional to the measurement variable upon application of force. The short nominal measurement distance of the ultra-miniature compression load cells due to their design provides a high degree of rigidity. If needed, the nominal characteristic value can be standardized in the sensor connection cable.

The new Scout VGS 4500 measuring station consists of measuring probes mounted on the front of the vehicle and a measuring cell installed within the vehicle. These two parts are connected via a suction hose. The system can be mounted on different type of vehicles such as a pickup truck, quad or car. To adapt to nature of the surface to be measured, the probe distance can be adjusted quickly and it is just as easy to store the entire front probe. With the Scout VGS 4500 measuring station from Schütz, very large sections of network can be inspected and the results can be recorded in a short time. With the vehicle-based measuring system, measurements are accurately taken at speeds up to 50 km/h. Even under the most difficult conditions, Scout VGS 4500 has proven its reliability. The system was successfully subjected to a resistance test in the desert at an outside temperature of over 36 degrees Celsius.

Max. display accuracy 10 μm or 1/64 inch. Repeat accuracy max. ±0.01 mm. Low-power LCD with decimal and fraction-inch function. Reading distance ≤2 mm. Incremental measurement and reset function. Direct reference/offset value input. Battery-buffered memory. Battery operation. MS500H sensor pluggable.

Due to its high resolution also when measuring long distances, linear displacement measurements up to 900 mm can be carried out. Conversions between rotatory and translation movements through ball screws, wire or cord connections and so on are not necessary for direct displacement measurement. Application fields include: —Electromagnets —Deformations - bending —Pneumatic cylinders —Length tolerances —Press-insertions (longitudinal press-fits) —Feed strokes —Machine hubs —Punch, knee lever or extruder distances —Hydraulic cylinders Due to the technology employed in potentiometric displacement sensors, they always operate with a sliding contact system. Special processes are applied to give the resistance tracks low friction, low tendency to stick/slip, resistance to abrasion and long-term stability. The rod is guided in a low-play floating frontal bearing. This absorbs small angular and parallel displacements.

Miniature wire-actuated encoder designed to capture linear distances with a maximum measurement length of 2000 mm. Compact design. Universally applicable thanks to standardized interfaces. Easy mounting. Measurement lengths up to max. 2000 mm. Potentiometer, voltage, power output or incremental encoder. Housing made of reinforced plastic.

The sensor model 8228 with its measuring accuracy of 0.05% F.S. (for the measuring ranges ≤ 1 bar, the measuring accuracy is 0.1% F.S.) ideally suited as a reference sensor. The compact dimensions, the robust housing and the industrial-grade output signal result in a very wide range of applications. All components in contact with media are made of stainless steel. An integrated measuring amplifier converts the measuring signals directly into interference-free voltage signals or current signals that can be transmitted over long distances. With the „gage“ measurement type, the pressure measurement is carried out against the ambient pressure, the sensor has a bore that is protected against ambient influences to compensate for the ambient pressure. With the „Absolute“ measurement type, the applied pressure is measured against an enclosed vacuum; this measurement type is available from the measuring range 0 ... 250 mbar. The electrical connection is made via an M12 x 1 connector.

1. Zero setting of the dial on any flat surface / measuring block 2. The required tolerance range is set on the dial in the normal way. In our example: ±10 3. The measuring operation is carried out very simply by inserting the specimens in the measuring stop 4. Reading of the measurement and the tolerance. The next measuring operation can begin

Electrostatics disturb almost all production processes. Eltex systems prevent uncontrolled discharges and integrate electrostatics precisely into your processes.In our product portfolio for measuring electrostatic charges and leakage resistances you will discover systems and products for many industrial sectors. Electric Field Meter EM03: Handy appliance for the measurement of static charges, measuring distance ranging from 2 to 20 cm. The field strength is converted automatically and displayed in volts. Measuring range from ±0 to ±200 kV, automatic switching between measuring ranges, measured values are displayed on a 2-line alphanumerical LCD display. Dimensions: 114 x 68 x 25 mm (L x W x D)