Results for
IGUS® GMBH
Germany
iglidur® G: The all-rounder The widest range of differing requirements are fulfilled by iglidur® G bearings. That's why this material is rightly termed universal. Recommended are applications with medium to high loads, medium surface speeds and moderate temperatures. iglidur® G is available as cylindrical bearings, plain bearings with flange and thrust washers. Maintenance-free, dry operation high wear-resistance Insensitive to dirt and dust Over 650 dimensions Delivery: from stock Low-priced
Request for a quoteIGUS® GMBH
Germany
Thrust bearing / Spherical axial bearings from igus d1 [mm]: Mechanical properties The self-aligning spherical igubal ® thrust bearings are very easy-to-mount units, which help to compensate for errors and prevent misalignments. The thrust bearing housing pad is made of the impact-resistant, stiff, thermoplastic composite material igumid G. The standard thrust bearing washer is made of iglidur® W300. This combination provides particularly good gliding and wear properties in relative movements. Loads The load carrying capacity of the spherical igubal® thrust bearing is very high in normal ambient temperature. In particular cases the load carrying capacity of the axial bearings should be checked in a practical trial with high constant loads and at higher temperatures. Coefficients of surface friction and speeds Taking the radial loads into account, maximum surface speeds up to 0.5 m/s rotating can be attained. Installation The axial bearing pad is mounted flush and secured. The spherical washer glides loosely in the pad and is held by the shouldered shaft mounted on it. Delivery program As standard, the spherical igubal® axial bearings are supplied in sizes of 5 to 20 mm. For other dimensions, please contact us. Special features Simple assembly Compensation of misalignments Compensation of edge loads Very good gliding and wear properties, low installation space When to use it? When you want to save weight When freedom from corrosion is required When a bearing with good friction coefficients is sought When not to use? When very heavy loads act When constant temperatures of more than +80℃ occur When high rotary speeds must be implemented. Thrust bearing / Spherical axial bearings from igus d1 [mm]:
Request for a quoteIGUS® GMBH
Germany
igubal® flange bearing EFOM With 2 mounting holes igubal® flange bearing EFOM igubal® flange bearing EFSM With 4 mounting holes, dimensional series E igubal® flange bearing EFSM igubal® flange bearing KFSM-GT With 4 mounting holes, dimensional series K igubal® flange bearing KFSM-GT igubal® flange bearing EFOM HT Applicable up to 200°C,resistant to chemicals , with 2 mounting holes igubal® flange bearing EFOM HT igubal® flange bearing EFSM HT Applicable up to 200°C,resistant to chemicals , with 4 mounting holes igubal® flange bearing EFSM HT igubal® flange bearing with ball pins, male thread igubal® flange bearing with ball pins - male threads for direct connections igubal® flange bearing with ball pins, male thread igubal® flange bearing with ball pins, female thread igubal® flange bearing with ball pins, female threads for direct connections igubal® flange bearing with ball pins, female thread igubal® flange bearings were developed for the bearing of shaft extensions or shaft bushings. Like all igubal® products, they consist of an igumid G housing and an iglidur® W300 spherical ball. igubal® flange bearings correspond to the dimensional series E and are offered with 2 or 4 mounting holes. Features igubal® flange bearings were developed for the bearing of shaft ends or shaft bushings. Like all igubal® products, it consists of a housing made of igumid G and a spherical ball in iglidur® W300. igubal® flange bearings correspond to the dimensional series E and are offered with 2 or 4 mounting holes. Application area As the igubal® flange bearings are also suitable for dry operation, they are particularly considered for applications in which the installation site is difficult, in humid or wet environment, or with special demands on hygiene. Thus the igubal® flange bearings are used for instance in wash-brush controls, in facade sunscreen systems, in materials handling systems and in bakery equipment. igubal® flange bearing - Applications Installation According to type, igubal® flange bearing are designed for mounting with 2 or 4 holes. The 2-hole types are provided with oblong holes that enable a trouble-free readjustment. A precise alignment of the bearing housing is not required as the flange bearing automatically compensates for error. Delivery program For shafts, igubal® flange bearings with 2 and 4 mounting holes are available in standard dimensions of 5 to 50 mm. For delivery times and more dimensions, you may please contact us. When to use it? When chemical resistance is required When a low-cost alternative is desired When dirt-resistant bearings are needed When misalignments should be compensated When fully split components are needed When not to use? When temperatures above +200°C prevail When an integrated collar is required When dimensions over 50 mm are needed When rotation speeds in excess of 0.5 m/s should be implemented igubal® flange bearing EFOM With 2 mounting holes igubal® flange bearing EFOM igubal® flange bearing EFSM With 4 mounting holes, dimensional series E igubal® flange bearing EFSM igubal® flange bearing KFSM-GT With 4 mounting holes, dimensional series K igubal® flange bearing KFSM-GT igubal® flange bearing EFOM HT Applicable up to 200°C,resistant to chemicals , with 2 mounting holes igubal® flange bearing EFOM HT igubal® flange bearing EFSM HT Applicable up to 200°C,resistant to chemicals , with 4 mounting holes igubal® flange bearing EFSM HT igubal® flange bearing with ball pins, male thread igubal® flange bearing with ball pins - male threads for direct connections igubal® flange bearing with ball pins, male thread igubal® flange bearing with ball pins, female thread igubal® flange bearing with ball pins, female threads for direct connections igubal® flange bearing with ball pins, female thread
Request for a quoteIGUS® GMBH
Germany
iglidur® flange bearing d1 [mm]: With this design it is possible to use the iglidur® high-performance bearings where housing bores with no precise tolerances are possible. When to use iglidur® flange bearings? When you want a screw flanged bearing When a clip bearing solution is not satisfactory as a sheet metal feedthrough When there is a housing with very rough tolerances When the tight fit of a press-fit bearing is not sufficient as an axial securing When not to use them? When an additional angle compensation is required igubal® flange bearing When a screw connection is not possible iglidur® clip bearing When a large guide length is necessary iglidur® G General features With this design it is possible to use the iglidur® high-performance bearings where housing bores with no precise tolerances are possible. The design enables high loads with minimum demand on the precision of the housing. iglidur® maintenance-free flange bearings are available in four materials - iglidur® G, iglidur® J, iglidur® X and iglidur® A180. Thus, with this design, a very wide range of applications - from the universal bearing through the highest wear resistance or temperature resistance (up to +250°C) up to FDA-compliant bearing solutions - can be covered. Installation Dependent on the stressing capacities, various mounting types are used. For low radial loads, it is enough to mount the iglidur® flange bearing with just two screws on a surface. For higher radial loads, it is advisable to support the iglidur® flange bearing in a bore on the reinforced side in the load direction. Large tolerances are permitted for this bore, as it is only to additionally support the iglidur® flange bearing. In order to support still higher radial loads, the iglidur® flange bearing can be press-fitted with the longer side in an H tolerance bore. The additional screw connection secures the firm seating of the bearing in the housing. For the mounting of the iglidur® maintenance-free flange bearing, no special tools or devices are necessary. The alignment of the bearing in multiple mounted shafts is easily possible at the installation. Available materials: iglidur® G, iglidur® A180, iglidur® J and iglidur® X The mounting of the iglidur® flange bearing: Simple and safe iglidur® flange bearing d1 [mm]:
Request for a quoteIGUS® GMBH
Germany
iglidur® clip bearing, metric d1 [mm]: iglidur® clip bearing, inch d1 [inch]: iglidur® clip bearings are especially intended for the shaft bushing through plates. For this reason the bearing has a flange on each of the two front sides. After the clip-on the bearings are secured on both sides in the plate. The clip bearings have chamfered slot on the side that enables the mounting of the bearing on one side. After the mounting the bearing straddles and lines the bore in the plate. The shaft prevents the clip bearing from slipping out of the bore. The bearing cannot slip out of the bore even in axial movements. Extremely simple mounting through lateral slot Maintenance-free and self-lubricating Good flexibility in punch hole Good abrasion resistance Quiet operation Suitable for rotary and linear movements Extendibility through the slot Undetachable through double flange Special dimensions possible Plate thicknesses from 3 mm to 4 mm available from stock Material: iglidur® M250 Special properties of the iglidur® clip bearings iglidur® clip bearings are made from the most abrasion-resistant material, iglidur® M250. iglidur® M250 is a bearing material for rugged, wear-resistant bearing systems for medium loads. The bearings are self-lubricating and can be used dry. If required the bearings can also be lubricated. The material iglidur® M250 is resistant to all common lubricants. The iglidur® clip bearings are the ideal solution for bearing functions with low loads. The easy mounting makes it ideal for applications with difficult bearing locations. Compressive strength The permitted static surface pressure of iglidur® M250 amounts to 20 MPa at room temperature. Due to the good adaptability to uneven surfaces of the bearing housing, a high pressure load capacity of the clip bearings persists even in punched holes. For the most small bearing surfaces, the good vibration dampening properties and the insensitivity to misalignment are of primary importance. Surface speeds Clip bearings are particularly wear resistant in slow rotating, oscillating and axial motions. You can find the maximum gliding speeds for the various motions for the iglidur® M250 material under the materials data link shown below. A lubrication at installation or continuous lubrication raises the permitted surface speeds. Clip bearings are available from stock in dimensions of 3 to 25 mm. Fixation Triflex RS For mounting, the bearings are laterally pressed together with the large flange. The chamfered slot makes the bearing spiral-shaped, whereby it can be easily inserted in the plate. The remaining slot in the attached clip bearing can compensate for linear expansions of the circumference. Thus narrow bearing clearances are possible with clip bearings. The bearing clearance is dimensioned in such a way that in a housing bore with a nominal diameter, a shaft made with the same nominal diameter turns easily. The clip bearing can be used in H-tolerance housings up to H13. The turning of the clip bearing in the bore is also permitted. Operating temperatures The wear resistance of the iglidur® clip bearings are excellent with operating temperatures till 80°C. Even at low temperature the bearings remain elastic and abrasion resistant. When to use it? When a sheet metal feedthrough is required When the bearing should be captively clipped on in a drill hole with rough tolerance For rotating, linear and pivoting movements When a quick-mounting bearing solution is sought Clip bearings application examples When not to use it? When constant temperatures of more than +80°C occur iglidur® G When a high-precision bearing is needed iglidur® J When the housing bore is more than 4 mm long iglidur® Clips 2 iglidur® MKM When very high surface pressures occur iglidur® G iglidur® clip bearing, metric d1 [mm]: iglidur® clip bearing, inch d1 [inch]:
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
BDP MECHANICAL COMPONENTS DEUTSCHLAND GMBH
Germany
For eletric motor, made by die casting and machining, material GD AlSi11 Cu2 (Fe) EN AB 46100 or ADC12, size Ø147mm x 67mm, weights 0,87kg, annual demands 40.000pcs.
Request for a quoteSPINDEL- UND LAGERUNGSTECHNIK FRAUREUTH GMBH
Germany
can be used for the external and internal treatment of workpieces coverage of a large speed range belt-driven, or with integrated/flange-mounted motor
Request for a quoteSPINDEL- UND LAGERUNGSTECHNIK FRAUREUTH GMBH
Germany
Bearings belong to those components which influence the production process considerably and contribute significantly to its quality. In addition they are normally subject to strong loads. A high quality and availability of equipment can be achieved by preventive maintenance based on its actual condition. Through the opportunity of reconditioning (rework) of bearings this process can be realized considerably more cost-efficient compared to exchange of bearings. Reconditioning of bearings and bearing units can already be economic from an outer diameter of 180 mm. The costs of reconditioning account to approx. 50 to 85 % of the sales price. Please consider the larger a bearing is the more economic is its reconditioning. Usually the lead time for reconditioning is even shorter than for newly produced bearings. In addition to repair of our own bearings we are also able to repair bearings made by other manufacturers.
Request for a quoteSPINDEL- UND LAGERUNGSTECHNIK FRAUREUTH GMBH
Germany
We produce diverse types of ball bearings, whose outer diameters lie in the range of 32 to 1600 mm. All of our products fulfil the most stringent requirements of the standards that are in line with DIN and ISO. The high precision of our ball and roller bearings matches the characteristics of comparable world-renowned ball bearing brands. Ball bearings in almost any ranges can be quoted and delivered upon request. SLF can fit your bearing requirement needs with special material, special lubrication, special heat treatment, special backlash and higher levels of precision. We also produce high quality thin section bearings for the semiconductor, scientific and robotic industries. Our portfolio of services also includes the reconditioning of ball bearings.
Request for a quoteSPINDEL- UND LAGERUNGSTECHNIK FRAUREUTH GMBH
Germany
At SLF we pride ourself in being one of the the word leaders in self-alinging bearings. We offer this style bearing with all the same eneeringing, heat treatment, lubrication and material options as our ball and cylindrical bearings. are two-rowed bearings with two tracks on the inner ring, and one common spherical track in the outer ring specially produced for bearing-related scenarios involving larger shaft deflections or shaft displacement version with cylindrical and cone-shaped bore hole
Request for a quoteSPINDEL- UND LAGERUNGSTECHNIK FRAUREUTH GMBH
Germany
also as an eccentric spindle sleeve adjustment of the working height via the tooth system on the outer diameter can transfer high axial/radial loads bored working spindle for execution of axial movements
Request for a quoteSPINDEL- UND LAGERUNGSTECHNIK FRAUREUTH GMBH
Germany
Spindle bearings are in SLF’s DNA. When it comes to Spindle Bearings we manufacture and design only the very highest quality in large renage of Options. are particularly applicable in scenarios involving machine tool building, as well as scenarios in which the bearing is subject to the most stringent requirements pertaining to precision or permissible speeds contact angle of 15° or 25° available Other contact angle and materials are available e DLR bearings are also available
Request for a quoteSPINDEL- UND LAGERUNGSTECHNIK FRAUREUTH GMBH
Germany
designed for various tool interfaces, e.g. HSK, SK, collet chuck slot and short taper equipped with manual or automatic clamping system permanent grease lubrication or oil-air lubrication
Request for a quoteSPINDEL- UND LAGERUNGSTECHNIK FRAUREUTH GMBH
Germany
equipped with sensor for section detection for absorption of particularly high radial loads stability of balancing quality reliably fulfils the most stringent precision requirements
Request for a quoteResults for
Bearings - Import exportNumber of results
15 ProductsCountries
Company type