Results for
SCHULZ STANZTECHNIK GMBH
Germany
Design and construction The Schulz ball caster „Blue-Line“ with a housing made of certified plastic and a gap-free, closed cover (without dirty edges), a plastic or stainless steel carrier ball and several support balls has been specially developed by us for use in the food industry. For this purpose they have the signal colour blue. The Schulz plastic ball castor „BlueLine“ is particularly easy to clean due to the new design with several dirt holes in the housing. Dimensions The pitch is determined by dividing the shortest edge length of the conveyed material by 3.5.
Request for a quoteIGUS® GMBH
Germany
xiros® A500 heat Plastic ball bearings for high temperatures up to +150°C Product range xiros® A500 chemistry Plastic ball bearings with high resistance against chemicals. Product range xiros® A500 economical alternative Plastic ball bearings as an economical alternative. Product range xiros® A500 wear resistant Plastic ball bearing with wear resistance improved by factor 3. Product range Cage: PEEK PA Balls ES = stainless steel GL = glas PAI = Polymer xiros® A500 heat Plastic ball bearings for high temperatures up to +150°C Product range xiros® A500 chemistry Plastic ball bearings with high resistance against chemicals. Product range xiros® A500 economical alternative Plastic ball bearings as an economical alternative. Product range xiros® A500 wear resistant Plastic ball bearing with wear resistance improved by factor 3. Product range
Request for a quoteIGUS® GMBH
Germany
igubal® rod end bearing, female thread With female thread in metric and inch dimensions igubal® rod end bearing, female thread igubal® rod end bearing, male thread With male thread in metric and inch dimensions igubal® rod end bearing, male thread igubal® rod end bearing CL For simplified mounting, with inner and outer threads in metric dimensions igubal® rod end bearing CL igubal® rod End Bearing CL DT For simplified installation, detectable with female thread in metric dimensions igubal® rod End Bearing CL DT igubal® fitting screw, mm Fitting screw with circlip igubal® fitting screw, mm When to use it? When you want to save weight When rotating, oscillating and linear movements should be implemented When high-frequency oscillations/vibrations predominate When a low-noise operation is desired When an electrically insulating part is required When freedom from corrosion is desired For combinations with pneumatic cylinders and gas struts When chemical resistance is required When high stiffening is required When not to use? When you have temperatures above +80°C (then HT options) When rotation speeds in excess of 0.5 m/s should be implemented When very high tensile and lateral loads prevail When applications should be implemented with hydraulic cylinder When dimensions over 30 mm are needed igubal® rod end bearing, female thread With female thread in metric and inch dimensions igubal® rod end bearing, female thread igubal® rod end bearing, male thread With male thread in metric and inch dimensions igubal® rod end bearing, male thread igubal® rod end bearing CL For simplified mounting, with inner and outer threads in metric dimensions igubal® rod end bearing CL igubal® rod End Bearing CL DT For simplified installation, detectable with female thread in metric dimensions igubal® rod End Bearing CL DT igubal® fitting screw, mm Fitting screw with circlip igubal® fitting screw, mm Special properties of the igubal® rod end bearings Maintenance-free, self lubricating High stiffening Very high fatigue strength in varying loads Compensation for alignment errors Compensation of edge loads Insensitive to dirt, dust and lint balls Resistant to corrosion and chemicals High dampening qualities Suitable for rotary, oscillating and linear movements Very low weight Dimensional series K and E, dimensions according to DIN ISO 12240 Version with metal sleeve in the spherical ball for enhanced torque Tolerances igubal rod end bearings can be used, according to the application, with different tolerances. They are designed with a large clearance in the standard product, which enables a secure operation even under high peripheral speeds. The bore of the inner ring has a tolerance according to E10. The shafts should have a tolerance between h6 and h9. Please contact us in case you require lower or more bearing tolerances. Loads igubal® rod end bearings take high forces in normal ambient temperatures, have excellent dampening properties and weigh only a fifth of the conventional metallic bearing housing. In particular cases the load carrying capacity of the rod end bearings should be checked in a practical trial especially with high constant loads and at higher temperatures. Coefficients of surface friction and speeds Rotary motions of the mounted shaft take place directly in the bearing ball made of iglidur® W300. The advantage of this plastic/steel plain bearing is that high speeds can be achieved in dry operation. Taking the radial loads into account, maximum surface speeds up to 0.5 m/s rotating can be attained. The maintenance-free igubal® rod end bearings casually permit linear and oscillating movements of the shaft. Delivery program igubal® rod end bearings are available in the dimensional series K and E for shaft diameters of 2 to 30 mm in all dimensions according to DIN ISO 12240, and of course respectively in the Form A - with male thread and Form B - with female thread The dimensional series K and partly E are moreover available in inch dimensions and – as special version – with a stainless steel sleeve in the spherical ball. Thereby an essentially higher tightening torque is possible than with the plastic spherical ball. Please ask us for other sizes. igubal® rod end bearings - Applications igubal® rod end bearings - Applications Temperatures Dimensional series K in A+B variants for temperatures upt to +200°C (HAT material).
Request for a quoteECKARDT SYSTEMS GMBH
Germany
Dosing system DB 10: lubrication made easy The dosing system DB 10 uses a pressure vessel with a capacity of 10 litres. This is equipped with a filler ball valve and plastic funnel, a pressure regulator with bleed screw and a safety pressure relief valve. A float switch is fitted to regulate the fill level. There are two dosing valves on the underside. This dosing system is available in the following versions: DB 10 H – with poppet valve DB 40 – with 40 litre reservoir DB 40 H – with 40 litre reservoir and poppet valve
Request for a quoteECKARDT SYSTEMS GMBH
Germany
Dosing systems The right amount every time Compact & efficient Our supply and dosing systems are designed to harmonize perfectly with all Eckardt lubricators. These range from small integrated dosing devices through to standalone oil supply solutions with filter units and tank heaters. Features & benefits • Individual dosing and storing solutions • Integrated tank heater and filter units optional • Suitable for oils of all manufacturers and viscosities • Available in all sizes and performance data Design versions and details Dosing system VB 10: the sound entry-level solution The VB 10 dosing system operates without any pressure. It hangs above the roller lubricator; the oil is supplied to the machine purely through the force of gravity. The capacity of the VB 10 storage container is 10 litres. Dosing system DB 10: lubrication made easy The dosing system DB 10 uses a pressure vessel with a capacity of 10 litres. This is equipped with a filler ball valve and plastic funnel, a p
Request for a quoteFRANKE GMBH
Germany
Franke slim bearings of the type LSA convince by their smooth running, extremely compact installation space, simple mounting and favourable price. Slim bearings of type LSA consist of an inner and outer race with hardened and profiled raceways and a plastic cage with retained balls. The rolling elements rest against the raceways at two points each, thus maintaining the 4-point system. The raceways are split and can therefore be changed elastically in diameter for installation.
Request for a quoteGEMÜ GEBRÜDER MÜLLER APPARATEBAU GMBH & CO. KG
Germany
The GEMÜ 728 2/2-way metal ball valve is motorized. It has a plastic actuator housing. A manual override and an optical position indicator are integrated as standard. The seat is made of PTFE. — High flow rates — Full-flow bore
Request for a quoteGEMÜ GEBRÜDER MÜLLER APPARATEBAU GMBH & CO. KG
Germany
The GEMÜ 717 2/2 or 3/2-way plastic ball valve has an ergonomically designed hand lever and is manually operated. The seat is made of PTFE. — High flow rates — Low weight — Nominal sizes: DN 10 to 100 — Operating pressure: to 16 bar depending on version and/or operating parameters — Media temperature: -20 to 100 °C depending on version and/or operating parameters
Request for a quoteRIPPERT ANLAGENTECHNIK GMBH & CO. KG
Germany
Up to three processes – cleaning, painting and drying in one booth. Multi-process booth Just one booth for cleaning, painting and drying (up to three processes). Dry paint filter and wet cleaning in one booth – that is actually a contradiction in itself. Thanks to the separate air guidance, the exhaust air is fed downwards through the grating when drying and laterally through the filter boxes when painting, so that very little moisture enters the dry filter and virtually no particles get into the cleaning water. In order to prevent the ingress of particles, the gratings can additionally be covered over during painting. Any paint that does get into the cleaning water is usually already dry, so that no dilution in the classic sense takes place; instead, it behaves like small, filterable plastic balls. Advantages:
Request for a quoteTOK EUROPE GMBH
Germany
Load capacity of up to 80 kg possible Allowable rotation speed 300+ rpm
Request for a quoteTOK EUROPE GMBH
Germany
Load capacity of up to 60 kg possible
Request for a quoteTOK EUROPE GMBH
Germany
Plastic ball bearing featuring a polyacetal (POM) outer race, and steel inner race. Its main applications are: office furniture, furniture, vending machines, and refrigerators. There are 3 different types of D-Series Bearings, each serving a different use of application: Hole, Screw, and Riveting bearings. In addition, there are 6 different types of outer housing shapes, which can be seen below. Dimensions range from φ9 to φ48, and load capacity ranges from 2kgf (4.40 lb) to 20kgf (44.0lb).
Request for a quoteFATH GMBH
Germany
Handles in various designs and dimensions: — ergonomic design and finger protection — electrostatically discharging — with/without bore and cover caps Front handle, handle, bridge handle, machine handle, comfort handle Material selection: — Plastic PA glass fibre reinforced, black — Plastic PA glass-ball reinforced, black System handle Material selection end piedes: — Plastic PA glass-ball reinforced, black Material selection tubes: — Carbon fibre, glossy finish — Aluminium, anodised — stainless steel — Steel plastik covered Strip handle Material selection handle strip: — Aluminium Material selection cover caps: — PA glass-fibre reinforced plastic Other sizes, other colors on request
Request for a quoteFATH GMBH
Germany
T-slot feet — to protect the floor and the aluminium profile — can also be used as spacers, e.g. when transporting aluminium profiles and frames — or as a buffer stop, e.g. for door frames incl. anti-slip-plate, prevents movement of T-Slot foot on slippery surfaces and absorbs some vibration can be mounted into the slot by a quarter turn Profile: 20, 30, 40 Profile slot: 5, 6, 8, 10 Material: Plate: PA plastic, glass ball reinforced Anti-slip plate: thermoplastic elastomer, ≈70 Shore A Color: black
Request for a quoteFATH GMBH
Germany
Lift castor system for a fast and flexible placing of plant and machinery or assembly tables; gear transmission ratio: 10:1 Max. Load: 500 kg per lifting unit Material: Housing: Die-cast aluminum with PTFE bearing Roller: Plastics PA with ball bearing Roller housing: Zinc plated steel Set: 4 lifting units 1 hydraulic drive unit 4 hydraulic pipes at each 3 m, pre-filled Extras: Other sets on request
Request for a quoteFATH GMBH
Germany
For precise positioning of dollys or material trolleys suitable for different wheel diameters no brakes needed self-adhesive, for tool-free assembly no screwing required, immediately ready for use Models: High / high, for light to medium weights Low / high, for medium to heavy weights Low / low, for heavy weights Different lengths available on request. Material: Alumnium Surface: Plain Extra accessories possible Compatible One-piece end caps; self-adhesive, screwable with optional screw-on set Yellow position markings with signal effect to indicate the position of the wheels from floor dollys or material trolleys in the parking rail Plastic PA, glass ball reinforced
Request for a quoteFATH GMBH
Germany
Adjustable feet in over 20,000 variations — fixed adjustable foot — hinged adjustable foot function: — screw-on (with screw-on hole/with extension arm/through accessories: floor mounting for trapeze plate) — levelable — swiveling — anti-slip (by accessories: anti-slip plate made of thermoplastic elastomer) — EDS-capable Plate shape and size: — Round — Trapezoidal shape — Square — Diameter 20 mm to 120 mm other shapes on request Material plate: — Plastic PA, glass ball reinforced — steel, galvanized — zinc die casting — stainless steel other materials and surfaces on request Threaded rods for adjustable feet with/without ball head — swivel range 0° - 20° degrees — M5, M6, M8, M10, M12, M14, M16, M20, M24, M30 — Length: 20 - 300 mm — Alternative: ball head with internal thread — Material: galvanized steel, stainless steel Colors: black, silver, other colors on request
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
TORWEGGE GMBH & CO. KG
Germany
Our flexible ball transfer units provide a simple solution for transporting lightweight to heavy goods along all directions. Our ball transfer units enable you to easily move, rotate and control your conveyed goods. The ball transfer units are constructed so that a very smooth run is possible in all directions, even when moving heavy loads (depending on the version). In a configuration where the ball transfer units are offset from the vertical with overhead mounting, it is possible to achieve a reduction in the load-carrying capacity of up to 50%. Many of our ball transfer units are low-maintenance and feature an oil-soaked felt seal against contamination. Ball transfer units with plastic load balls are excellent for moving loads with delicate surfaces (such as glass, polished aluminum, brass and steel sheet).
Request for a quoteTORWEGGE GMBH & CO. KG
Germany
Our flexible ball transfer units provide a simple solution for transporting lightweight to heavy goods along all directions. Our ball transfer units enable you to easily move, rotate and control your conveyed goods. The ball transfer units are constructed so that a very smooth run is possible in all directions, even when moving heavy loads (depending on the version). In a configuration where the ball transfer units are offset from the vertical with overhead mounting, it is possible to achieve a reduction in the load-carrying capacity of up to 50%. Many of our ball transfer units are low-maintenance and feature an oil-soaked felt seal against contamination. Ball transfer units with plastic load balls are excellent for moving loads with delicate surfaces (such as glass, polished aluminum, brass and steel sheet).
Request for a quoteALFRED SCHÜTZE APPARATEBAU GMBH
Germany
SCHÜTZE ZIP 52 double diaphragm pump Pump made from plastics, balls made from stainless steel. Incl. all necessary fittings as: air pressure regulator for pump pressure, air pressure regulator for atomizing air, material pressure regulator, anti-pulsation tank, reflow faucet max. pressure: 6 bar.
Request for a quoteROS ROLLENTECHNIK GMBH
Germany
Conveyor rollers made off — Plastic (with steel balls or stainless steel balls) — Steel, galvanized (with steel balls) Roller diameter: 48 mm For axis diameter: 6 mm, 8 mm
Request for a quoteROS ROLLENTECHNIK GMBH
Germany
Spare parts for conveyor systems Bearing inserts from — galvanized sheet steel (with oiled ball bearing, in antistatic design) — Plastic, grey (polypropylene), with black plastic seal (polyamide) and stainless steel balls — Plastic, black (polypropylene), with black plastic seal Labyrinth (polypropylene) and RS deep groove ball bearing (in antistatic design) — Plastic, blue (polypropylene) with blue (polypropylene) and double stainless steel ball row Pipe diameter: — 20x1.5 mm — 30x1.5 mm — 30x2 mm — 40x1.5 mm — 40x2.3 mm — 50x1.5 mm — 50x2.8 mm — 60x2 mm Axle diameter: — 6 mm — 8mm — 10mm — 12mm
Request for a quoteResults for
Plastic balls - Import exportNumber of results
23 ProductsCountries
Company type
Category