Results for
SHENZHEN PROMOSTAR HARDWARE CO.,LTD
Germany
These are the pipes made from aluminum,which as the connector to connect the parts.
Request for a quoteIDG-DICHTUNGSTECHNIK GMBH
Germany
Face seal used for rotary and oscillating motion in pipe joints and rotary actuators
Request for a quoteSCHWEIZER GMBH & CO. KG
Germany
Stainless steel pipe connectors and ball joints are used for quick dismantling of two pipes. The ball joints offer the additional advantage of attaching the pipes at a special angle.
Request for a quoteIDG-DICHTUNGSTECHNIK GMBH
Germany
Face seal used for rotary and oscillating motion in pipe joints and rotary actuators. Used at low to high pressure and low speed
Request for a quoteTRACTO-TECHNIK GMBH & CO. KG
Germany
Quick click-shut coupling (QuickLock) without threads, no lubrication or elaborate screwing required Fast rod insertion and removal Approximately 40 % quicker installation than screwed rods Absolute stable connection Works around offset pipe bends and joints Minimal deformations Made from one piece of steel Rigid, low wear, as no clamping jaws required No slipping back of the bursting rods due to elastic pulling forces Bursting rod system with practical bursting rod accessories
Request for a quoteGRÜNING & LOSKE GMBH
Germany
Short description: Designed for smaller lines, with front jet In the case of the traction nozzle the patented fluid mechanics (patent no.: DE 19516780) and two different jet angles ensure a very high pulling efficiency, which leads to an efficient dirt transpoprt. This small maneuverable nozzle is ideal for cleaning smaller lines where good pulling properties are required. The traction nozzle is also available with front jet. It is successfully used in difficult pipes (set-off joints, bends etc.).
Request for a quoteGRÜNING & LOSKE GMBH
Germany
Short description: Designed for smaller lines, without front jet In the case of the traction nozzle the patented fluid mechanics (patent no.: DE 19516780) and two different jet angles ensure a very high pulling efficiency, which leads to an efficient dirt transpoprt. This small maneuverable nozzle is ideal for cleaning smaller lines where good pulling properties are required. The traction nozzle is also available with front jet. It is successfully used in difficult pipes (set-off joints, bends etc.).
Request for a quoteOKS SPEZIALSCHMIERSTOFFE GMBH
Germany
For mounting screwed connections, e.g. at combustion engines, threads on pipe fittings, flange joints and fittings of superheated steam lines, exhaust pipe and combustion chamber screwed connections, gas and oil burner mounting bolts To prevent burning together, seizing or rusting-on of screwed connections at water influence Suitable for brake systems of vehicles Advantages and benefits Excellently suited for preventing binding of threads exposed to high temperatures, corrosive environments and moisture Highly effective due to high level of pressure absorption Excellent corrosion protection Absolutely resistant to fresh water and sea water Extremely adhesive No classification according to (EG) No. 1272/2008 For best adhesion, clean contamination and other lubricants from thread and slide surfaces. Best way is to clean mechanically first (for example, with a wire brush) and then with OKS 2610/OKS 2611 universal cleaning agent. Use a brush, spatula or similar
Request for a quoteOKS SPEZIALSCHMIERSTOFFE GMBH
Germany
Assembling screw threaded connections subjected to high temperatures and corrosive influences Screwed connections at pipe fittings, flange joints and fittings in superheated steam lines Combustion chamber screwed connections and mounting bolts of gas and oil burners Screwed connections at combustion engines, exhaust systems, silencers and exhaust gas pipe connections Advantages and benefits Allows reliable non-destructive dismantling even after longer operating period under high operating and ambient temperatures Provides an optimal ratio of screw pretension and tightening torque Electrically conductive To achieve optimal adhesion clean the thread or the sliding surface first mechanically and then with OKS 2610/OKS 2611 universal cleaner to remove soiling as well as any lubricant residues. Use a brush, spatula or similar to apply a sufficient amount of paste to the head or nut contact surface and to the thread. Spray on evenly OKS 241 spray. The paste will also act as a sealant.
Request for a quoteOKS SPEZIALSCHMIERSTOFFE GMBH
Germany
Assembling screw threaded connections subjected to high temperatures and corrosive influences Screwed connections at pipe fittings, flange joints and fittings in superheated steam lines Combustion chamber screwed connections and mounting bolts of gas and oil burners Screwed connections at combustion engines, exhaust systems, silencers and exhaust gas pipe connections Advantages and benefits Allows reliable non-destructive dismantling even after longer operating period under high operating and ambient temperatures Provides an optimal ratio of screw pretension and tightening torque Electrically conductive Also available as spray version OKS 241 To achieve optimal adhesion clean the thread or the sliding surface first mechanically and then with OKS 2610/OKS 2611 universal cleaner to remove soiling as well as any lubricant residues. Use a brush, spatula or similar to apply a sufficient amount of paste to the head or nut contact surface and to the thread.
Request for a quoteOKS SPEZIALSCHMIERSTOFFE GMBH
Germany
Assembly lubrication of screw connections of high-strength steel subject to high temperatures, corrosive influences in chemically aggressive environments, e.g. on gas and steam turbines in power plants, combustion engines, threads on pipe fittings, flange joints and fittings in superheated steam lines, exhaust pipe and combustion chamber screwed connections etc. Parting lubrication of materials with a tendency to seize up, e.g. V2A, V4A and high-temperature steels Advantages and benefits Excellently suited for preventing seizing and binding Highly effective against corrosion affects Free of lead compounds, sulphides, chlorides and fluorides For best adhesion, clean the threads and sliding surfaces from dirt and other lubricants. Best way is to clean mechanically first and then with OKS 2610 or OKS 2611 universal cleaner. Apply paste evenly in sufficient amount onto head/nut support and thread or onto the sliding areas with brush, spatula, etc.
Request for a quoteKOREMA® GMBH & CO.KG
Germany
This is the most installed version of the fabric expansion joints (KOREMA® type A3 or AC3 as well as B3 or BC3). The name »flange-type« is used for expansion joints located between pipe or duct end flanges. For existing plants, the flange design varies according to customers’ requirements or depending on the constructed steel design. For innovative designs KOREMA® will identify the suitable technical and economical solution. Special design: supplied as »open« multilayer expansion joint. On-site service available exclusively from the KOREMA® service team. Insulation is incorporated to protect the expansion joint against abrasion as well as for thermal insulation. The choice of insulating material, either mineral wool or ceramic felt, depends on the design temperature. For operation at or below dew point, a vulcanized elastomeric layer is available. Pre-assembled units, complete with liners and clamp bars, are available.
Request for a quoteR&S PAPIERVERARBEITUNGS-GMBH
Germany
You will find: crevice nozzle in two lengths and pipe diameters Upholstery nozzle, with thread lifter in different pipe diameters Suction brush, with swivel joint in various pipe diameters Suction hose, complete with connections and hand tube Telescopic tube, various telescopic tubes in different tube diameters for vacuum cleaners of well-known manufacturers
Request for a quoteGRÜNING & LOSKE GMBH
Germany
Short description: For pipes and sewers from 75 to 250 mm The DN 75 mini chain cutter is used in pipes and sewers from 75 mm to 200 mm in diameter. It is equipped with two chain inserts which are adjustable to the particular diameter of the pipe. Without HP swivel joint the mini chain cutter can be used in pipes from 100 mm in diameter with elbows up to 90º. New: with stainless steel penetrator. With 2 year warranty according to KEG´s Terms of Guarantee.
Request for a quoteGRÜNING & LOSKE GMBH
Germany
Short description: For pipes and sewers from 50 to 100 mm The DN 50 hummingbird cutter is used in pipes and sewers from 50 mm to 100 mm in diameter. It is equipped with two chain inserts which are adjustable to the particular diameter of the pipe. Without HP swivel joint the hummingbird cutter can be used in pipes from 50 mm in diameter with elbows up to 90º. New: with stainless steel penetrator. With 2 year warranty according to KEG´s Terms of Guarantee.
Request for a quotePROPACK DICHTUNGEN UND PACKUNGEN AG
Germany
Non flamable High electric- and thermal isolation capability Dimensionally stabil Good mechanical structural strength Technical parameters pH 3 - 9 Temperature: t = -100 … +700 °C, short term up to 800 °C Main application Furnace, boiler and chimney doors Expansion joints Exhaust pipes Suitable for Power plant Furnace construction
Request for a quotePROPACK DICHTUNGEN UND PACKUNGEN AG
Germany
Universal fiber based high pressure gasket Characteristics A perfect selection of gasket material is based on operating conditions like pressure, temperature, media, surface pressure, Nonstick coating assures quick and scaling free disassembling Do not use any surface treatment! Technical parameters Temperature: t = -100 … +200 °C, short term up to 280 °C Pressure: p = 120 bar mainapplication Tube and pipe flanges Vessels Boilers Cylinders Joints Casings Lids Suitable for All Industries Approvals DVGW KTW BAM Form of delivery Sheets 1500 x 1500 mm in thickness of 0.5/0.8/1.0/1.5/2.0/3.0 mm or cut gaskets according to drawing or EN and international Standards Special dimensions and further gasket material styles from recognised manufacturers on request.
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
WHITE STEEL GMBH
Germany
DESCRIPTION High stability on high capacity. Can handle multiple ointment viscosity and types Type of metal used S.S 316 / 304 Certifications ISO 90012015, OHSAS 180012007, ISO 500012011, ISO 450012018 SPECIFICATION Preparation unit tanks for first and second phase Storage tank equipped with flowmeter system Homogenizer Sanitary centrifugal pump Mechanical filter Filter platform collector Pipes and fittings All joints are tic and orbital welded, polished and treated Stainless steel Teflon check valves, Pipe tri clamp joints. The production capacity varies depending on the type of products Gear pump cycle of the feeding device can speed up product forming and rapid discharge Semiautomatic weigh filling machine for gallons. Monoblock filling and capping machines feeding and collecting tables HMI and SCADA with touch screen system. Available certification up on your request UL, CE, GMP, FDA, ASME.
Request for a quoteCBG COMPOSITES GMBH
Germany
High-temperature vacuum-formed products made from biosoluble ceramic fibres are lightweight and solid parts or structural elements that can be used at temperatures up to 1.400 °C in air and in aggressive environments, including direct contact with liquid metals. — 100% biosoluble — high temperature resistance — low thermal conductivity — high chemical resistance * — low weight — good tear resistance — high flexibility — easy processing — complicated geometries can be produced — recyclable * to achieve higher acid resistance, a special coating is required. Available from manufacturer. Application: Burner plant components, crucibles, thermocouple housings, coupling devices in continuous casting plants, channel elements of metal troughs, inlet device in the melting of non-ferrous and ferrous metals, gasket in aluminium foundries, gaskets in blast furnaces, expansion joints, pipe insulation, catalyst insulation, repair work in the high temperature range.
Request for a quoteHEXPOL TPE GMBH
Germany
Introduction Dryflex PS are a range of thermoplastic elastomer (TPE) compounds designed for seals and pipe joints used in waste water applications. What are TPEs? TPEs are a family of polymer compounds which display elastic and rubber-like properties at their service temperature. Like thermoplastics, when heated and with the application of shear force, TPEs become free-flowing and when cooled regain their original structure and stability. Unlike the chemical cross-linking which occurs in thermoset rubbers, TPE involves purely physical cross-linking, which can be reversed via the further application of heat, this makes it possible to re-use all production waste and end of life products can be easily reprocessed. Product Assurance We support our customers by proving the performance of our products via relevant testing and working with industry standards. The Dryflex PS grades meet the requirements of EN 681-2:2000, the European Standard EN 681-2, Type WT. This testing allows our cus
Request for a quoteResults for
Pipe joints - Import exportNumber of results
21 ProductsCountries
Company type