Vacuum dryers - Import export

KET energy-efficient dryer with heat pump and buffer 20 m³ - 60 m³ stacking space The KET has an energy-saving heating system. The heat pump is the heart of the plant, it heats and cools. The cooling system condenses the moisture escaping from the wood and uses the heat this produced to heat the system. The system is supplemented by a buffer which makes use of the stored heat to heat up the vacuum dryer. Increases energy efficiency by 25 % Surplus energy from drying is used for heating The heat pump is used in the heating up phase for heating and demoisturizing No water connection required No heating connection required Areas of application: Sawmills, lumber and hardwood trade, wood industry

KCT circular vacuum dryer 20 m³ - 60 m³ of stacking space The KCT is characterizedby the advantageous arrangement of its valves. It can easily be connected to existing heating systems and requires but very little heating power. Energy: hot water or electric heating Putting fan on side enhances its performance Measuring point cables on carriage Active cooling in the equalization phase Detection of condensed water Heat and cold registers made of stainless steel Areas of application: Sawmills, lumber and hardwood trade, wood industry

KVT vacuum dryer with 5 m³ - 10 m³ of stacking space The KVT is characterized by its simply demoisturizing system by way of the vacuum pump. Putting the fans on the size – as in the larger circular dryer – enables the side stakes of the stored wood to be used. Re-stacking is no longer necessary. The vacuum dryer is connected to the hot water heating system already in place or run by direct electric heating. Dries valuable wood thicker than 50 mm 3-5 times as fast Lower energy requirement thanks to short drying times No cracking and no distortion owing to low temperatures in the vacuum No emissions thanks to environmentally compatible drying Uniform ventilation thanks to fans on side No re-stacking on special stakes through cross-ventilation Areas of application: Furniture industry, carpenters

The KCT, KET, KVT and KIT model vacuum dryers with additional equipment for heat treatment in compliance with IPPC All vacuum dryers from Kronseder can be additionally equipped to perform heat treatment in compliance with IPPC. Up to 6 sensors are available for heat treatment, whose measured values are stored for a protocol by the visualization of the Kronseder MK 200 control.

KCT circular vacuum dryer with additional equipment for smoking oak 10 m³ - 40 m³ of stacking space The KCT Eurovac circular vacuum dryer conforms to the requirements for smoking. The measuring equipment and the control valves are made of stainless steel. As is the carriage with rollers. The vacuum pump meets ATX requirements. The vacuum chamber is equipped with a ventilation system so that you can evacuate the ammonia at the end of the smoking process. The MK 200 control from Kronseder meets the requirements of the smoking process and controls the process for optimum coloring.

Braid of ePTFE yarn with Incorporated Graphite and Run-In Lubricant Characteristics Excellent heat conductivity Maximum protection of shaft against wear (HRC 25 is sufficient) Extended MTBF Easy and safe installation and handling No ageing process Operating range Pressure [p max]: 25 bar, Velocity [v max]: 25 m/s Pressure [p max]: 250 bar, Velocity [v max]: 2 m/s Pressure [p max]: 100 bar Temperature: t = -100… +280 °C pH: 0 - 14 Density: 1.50 g/cm³ Main application Centrifugal pumps Mixer Agitators Autoclave Filter Refiner Kneader Paddle dryer Vacuum pumps Suitable for Universal use Waste water technology Acids Alkaline solutions Oil and grease Form of delivery This packing can be manufactured in dimensions from 10 to 40 mm as well as in intermediate, inch sizes and special measurements. Available from 4 to 9 mm in square X-Section as Style P1P. 04 - 09 mm on 1kg spool 10 - 15 mm on 2,5 kg spool 16 - 25 mm on 5 kg spool Special length, pre-cut or die formed rings on...

KIT vacuum interval dryer 1,5 m³ - 4,50 m³ of stacking space This energy-saving system works on the principle of conventional drying with an inlet air flap and outlet air flap. Used for quickly demoisturizing the vacuum pump. Dries valuable wood thicker than 50 mm 3-5 times as fast Dries valuable wood thicker than 50 mm 3-5 times as fast Lower energy requirement thanks to short drying times No cracking or distortion through lower temperatures in the vacuum Longitudinal layout makes best use of space Areas of application: Carpenters, musical instrument makers, weapons industry, lathe work