Switches - Import export

The electronic temperature switch of BEDIA is fitted with thin-film resistor Pt 1000 in a bridge circuit. This sensor element provides close switch point tolerances and a quick response. Switch point and reset hysteresis may be selected within the admissible operating range when ordering so as to allow the monitoring of both very wide and very close temperature ranges. The switching output is protected from short-circuit and overload. The short-circuit current is limited by the output transistor switching off inthe event of a fault. It will automatically reset as soon as the fault has been remedied. The switch is available with ground-connected, plus-connected or potential-free DC switching output. The switch is open in the event of power failure or disconnection of the power supply, independed of the switching function. It is available both as normally open (NO) or normally closed (NC) switch.

These high-power bimetal operated temperature switches are available either with normally closed (NC) or normally open (NO) contact configuration. The robust round metal enclosure accommodates a resilient preloading disk, a bimetal disk and a silver contact. The compact switch system is covered by means of a plate which also carries a silver contact and is isolated from the enclosure by means of an isolating washer. The resilient preloading disk ensures excellent performance. The resilient preloading disk keeps the contact pressure constant throughout the entire temperature range of the BEDIA switch until switching occurs. The mechanically and electrically unloaded bimetal disk snaps over at a preset temperature, with either opening or closing the contact arrangement. The bimetal will only snap back to its initial condition after the temperature has dropped significantly.

Compact braided round copper flexibles made from Cu-ETP1 and Cu-OF1, LEONI Histral® alloys upon request, in bare, tin-plated, nickel-plated or silver-plated, in hard or soft annealed. Single-wire diameter ranging from Ø 0.05 mm to Ø 0.10 mm. Cross-section ranging from 0.047 mm² to 25 mm² (bigger cross-sections upon request). Round copper braids are characterised by a very high degree of dimensional accuracy and a very high Flex life. They are absolute free from twist and support an automatic further processing. Compact braided round copper flexibles are particularly suitable for carbon brushes industry, connection technology, switches or aviation industry.

Inductive limit switches for the optional attachment to pneumatic diaphragm actuators. Self sufficient position detection for on/off and control valves.

Inductive and mechanical limit switches for the optional attachment to pneumatic piston actuators.

The electronic pressure switch DS 400 is the successful combination of — intelligent pressure switch — digital display and has been specially designed for numerous applications in various industrial sectors. As standard the DS 400 offers a PNP contact and a display module, which is mounted rotable in the ball housing. Additional optional versions like e.g. an intrinsically safe version, a second contact and an analogue output complete the profile. Features: — nominal pressure: 0 ... 100 mbar up to 0 ... 600 bar — accuracy: 0.35 % (opt. 0.25 %) FSO — indication of measured values on a 4-digit LED display — rotatable and configurable display module Optional Features: — IS-Version Ex ia = intrinsically safe for gases — pressure sensor welded — customer specific versions

Features: — nominal pressure: 0 ... 2 bar up to 0 ... 400 bar — accuracy: 1 % FSO — 1 or 2 contacts — configurable via PC or programming device P6 — diaphragm ceramic (96 %) Optional Features: — oil- and fat free application

The electronic pressure switch DS 400P is the successful combination of — intelligent pressure switch — digital display and has been developed for process industry; especially for food industry and pharmacy. As standard the DS 400P offers a PNP contact and a rotable display module with 4-digit LED display. Optional versions like e.g. an intrinsically safe version, max. 2 contacts and an analogue output complete the profile. Features: — nominal pressure: 0 ... 100 mbar up to 0 ... 40 bar — accuracy: 0.35 % (opt. 0.25 %) FSO — 1 or 2 independent PNP contacts, freely configurable — indication of measured values on a 4-digit LED display — rotatable and configurable display module — hygienic process connections with flush stainless steel diaphragm Optional Features: — IS-version Ex ia = intrinsically safe for gases

The electronic pressure switch DS 200P is the successful combination of — intelligent pressure Switch — digital Display and is suitable for the usage with viscous and pasty media. As standard the DS 200P offers a PNP contact and a rotatable display module with 4-digit LED display. Optional versions like e.g. an intrinsically safe version, max. 4 contacts and an analogue output complete the profile. Features: — nominal pressure: 0 ... 100 mbar up to 0 ... 40 bar — accuracy: 0.25 % / 0.35 % / 0.5 % FSO — rotatable and configurable display module — indication of measured values on a 4-digit LED display — configurable contacts (switch on / switch off points, hysteresis / window mode, switch on / switch off delay) Optional Features: — analogue output — IS-Version Ex ia = intrinsically safe for gases — customer specific versions

Features: — nominal pressure: 0 ... 1 bar up to 0 ... 10 bar, -1 bar ... 0 bar — compact design — 1 or 2 contacts — configurable via PC or programming device P6 — silicon sensor, RTV — accuracy: 1 % FSO

The electronic pressure switch DS 214 for very high pressure up to 2200 bar has been designed especially for use in plant and machine engineering as well as in mobile hydraulics. The DS 214 has one 1 contact with standard version, this can optionally be upgraded up to four independent contacts. Via the rotatable modul with an integrated 4-digit display the DS 214 can be programmed easily and comfortably. Features: — nominal pressure: 0 ... 600 bar up to 0 ... 2200 bar — accuracy: 0.35 % FSO — indication of measured values on a 4-digit LED display — rotatable and configurable display module — 1, 2 or 4 independent PNP contacts, freely configurable — pressure sensor welded — extremly robust and excellent longterm stability Optional Features: — adjustability of span and offset (4 ... 20 mA / 3-wire) — customer specific versions

The electronic pressure switch DS 200 is the successful combination of — intelligent pressure switch — digital display and has been specially designed for applications in various industrial sectors. As standard the DS 200 offers a PNP contact and a rotatable display module with 4-digit LED display. Optional versions like e.g. an intrinsically safe version, max. 4 contacts and an analogue output complete the profile. Features: — nominal pressure: 0 ... 100 mbar up to 0 ... 600 bar — accuracy: 0.35 % (opt. 0.25 %) FSO — indication of measured values on a 4-digit LED display — rotatable and configurable display module — 1, 2 or 4 independent PNP contacts, freely configurable — configurable contacts (switch on / switch off points, hysteresis / window mode, switch on / switch off delay) Optional Features: — IS-version Ex ia = intrinsically safe for gases — pressure sensor welded — customer specific versions

Features: — nominal pressure: 0 ... 6 bar up to 0 ... 600 bar — accuracy: 0.5 % FSO — 1 analog output and up to 2 contacts — display and housing rotatable — perfect for oxygen applications

The electronic pressure switch DS 202 is the successful combination of — robust pressure transmitter — digital display and has been specially designed for numerous applications in various industrial sectors. As standard the DS 202 offers a PNP contact and a rotable display module with 4-digit LED display. The transmitters are suitable for an unrestricted use in oxygen applications up to 600 bar and an intrinsically safe IS-Version. Features: — nominal pressure: 0 ... 6 bar up to 0 ... 600 bar — accuracy: 0.5 % FSO — indication of measured values on a 4-digit LED display — rotatable and configurable display module — 1, 2 or 4 independent PNP contacts, freely configurable Optional Features: — IS-Version Ex ia = intrinsically safe for gases — oxygen application — customer specific versions

The DS 233 is a differential pressure switch with digital display for non-aggressive gases and compressed air. Because of its compact and robust aluminium housing it is particularly suited for machine and plant engineering. Basic element of the DS 233 is a piezoresistive silicon pressure sensor, which features high accuracy and excellent long term stability. As standard the DS 233 offers a PNP contact and a rotatable display module with 4-digit LED display for representing the differential pressure. Optional up to 2 freely configurable contacts are available. Features: — nominal pressure: 0 ... 6 mbar up to 0 ... 1000 mbar — accuracy: 0.35 % FSO — aluminium housing — rotatable and configurable display module — 4-digit LED display — suited for non-aggressive gases and compressed air Optional Features: — 1 / 2 PNP contacts — customer specific versions

The electronic pressure switch DS 201 is the successful combination of — intelligent pressure switch — digital display and has been specially designed for universal usage in industry applications. The DS 201 is available with flush pressure ports for viscous, pasty and highly contaminated media. As standard the DS 201 offers a PNP contact and a rotable display module with 4-digit LED display. Optional versions like e.g. an intrinsically safe version, max. 4 contacts and an analogue output complete the profile. Features: — nominal pressure: 0 ... 400 mbar up to 0 ... 600 bar — accuracy: 0.5 % FSO — indication of measured values on a 4-digit LED display — rotatable and configurable display module — 1, 2 or 4 independent PNP contacts, freely configurable Optional Features: — IS-version Ex ia = intrinsically safe for gases — pressure port PVDF — customer specific versions

The electronic pressure switch DS 201P is the successful combination of — intelligent pressure switch — digital display and is designed for universal applications in the mechanical engineering and other industries where a flush stainless steel diaphragm is necessary. This can be the case, for example, with higher viscous or slightly contaminated fluids. For usage with higher media temperature optionally a cooling element up to 300 °C is available. Features: — nominal pressure: 0 ... 60 bar up to 0 ... 400 bar — accuracy: 0.5 % FSO — 1, 2 or 4 independent PNP contacts, freely configurable — rotatable and configurable display module — indication of measured values on a 4-digit LED display Optional Features: — IS-version Ex ia = intrinsically safe for gases — cooling element up to 300 ° C — customer specific versions

Features: — nominal pressure: 0 ... 2 bar up to 0 ... 400 bar — accuracy: 1.5 % FSO — display and housing rotatable — up to 2 contacts — configurable via display Optional Features: — analog output

The electronic pressure switch DS 350 is interesting for all users in plant and machine engineering, due to the integrated IO-Link interface to exchange process data, diagnostic reports and status messages with a superordinate control level, as standard. In addition, further information can be retrieved that allow conclusions to the application process. Especially in mechanical engineering, great demand for flexible operating conditions have to be satisfied. Features — Nominal pressure from 0 ... 100 mbar up to 0 ... 600 bar — accuracy: 0.5% / 0.35 % (opt. 0.25 %) FSO — IO-Link according to specification V 1.1 — smart sensor profile — data transfer 38.4 kBaud — indication of measured values on a 4-digit LED display — rotatable and configurable display module — parameter settings via IO-Link or menu (VDMA-conform) — additional information via IO-Link accessible Optional features — different mechanical connections

■ Configurable output signal (4...20 mA, 0...20 mA, 0...5 V, 0...10 V, ±5 V, ±10 V) ■ DIN rail mounting ■ Low residual noise ■ Built-in cable break detection with alarm-output

Temperature is one of the most measured physical parameters. Despite this, precise temperature measurement is one of the most difficult tasks in motor technology. To meet the constantly increasing requirements for improved motor performance, higher efficiency and reduced emissions, it is necessary to use reliable and precise sensors in modern motor control systems. The increased requirements over the last few years regarding measurement accuracy and reliability of temperature measurements has meant that many equipment operators must reconsider the suitability and performance capacity of their temperature measurement equipment. Resistant thermometers can be used between -200 °C and +850 °C. An important common property is that their output parameters are available in the form of electric signals that can be relatively easily transferred to measurement and control instruments for processing, storage and display.

This temperature sensor is for measuring the temperature of liquid and gaseous media in engines, sets of machines and utility vehicles. A Pt 1000 thin-film precision resistor is used as the measuring element. The temperature-dependent resistance of the Pt 1000 is evaluated by an electronic circuit and outputted as a temperature-dependent voltage at the sensor‘s output. The interrelationship between temperature and voltage corresponds to the characteristic curve for the Pt 1000 and is thus nearly linear. The assignment between temperature and output voltage is nearly freely selectable, the lesser temperature corresponding to the lesser output voltage. The sensor‘s lowest possible output voltage is 0.1 V and its greatest is 10 V. The output is overload-proof and short-circuit-proof. The sensor has no mechanical moving parts and so is not susceptible to vibration and soiling.

i/p converter for the electrical control of pneumatic positioners. Suitable for field and switch cabinet assembly. Suitable for remote control of valves in hazardous areas. Also in Ex version II 2 G EEx ib IIC T6.

3DInspect is a uniform and user-friendly software tool for all 3D sensors from Micro-Epsilon. Parameter setting of the 3D sensors and recording of the measurement data are done directly in the 3DInspect software. Powerful tools allow point cloud alignment and filtering, intuitive detection and selection of relevant areas, and program combination. The 3D point clouds can be processed as required and measured values can be output to the controller.

Characteristics: — nominal pressure ranges from 0 ... 1 bar up to 0 ... 10 bar also -1 ... 0 bar — accuracy: 0.5 % FSO — compact design — IO-Link according to specification V 1.1 — silicon sensor, RTV Applications: — Pneumatics — Vacuum technology

DM-VMS

Electrical cabinets contain the electrical and electronic components of a process engineering system, a machine tool, or production equipment that is not directly located in the machine. They are manufactured by special switch cabinet builders or by the machine manufacturers themselves. To save costs, there are automation solutions that are not only worthwhile for large production series, but are also suitable for the more efficient and economical production of individual and small series. Metzner offers a unique and comprehensive system solution to reduce your expenses in switchgear construction. Depending on your requirements, different stripping and crimping machines are available, which differ in terms of design, performance and degree of automation. METZNER TRIATHLON SERIES - for precise cutting to length and one- or two-sided stripping - for crimping the ferrules (single- and double-sided) - for individual labelling of strands with different printing method

DPWL 11 waterproof IP 67

TMSE 10 4.9x4.5 -55 C to +125 C