Steel - Import export

Wrapped spring steel plain bearing | Requires maintenance | DIN 1498 | DIN 1499 FER-MET® is a spring steel plain bearing without integrated sliding material. Lubrication of the bearing point is necessary. Very high load capacity and impact resistance for heavy-loaded applications with impact loads. Very wear-resistant. A standard gap design with a straight slot and without chamfer inside [EG], but can also be manufactured with other slot shapes if required. For technical details, please visit the product page on our website!

Solid, turned, grinded and hardened steel plain bearing | Requires maintenance FER-MAS® is a steel plain bearing without integrated sliding material. Good lubrication is required! Suitable for highest loads, insensitive, long service life. For technical details, please visit the product page on our website!

Wrapped composite sliding bearing with lubrication pockets/ copper-plated steel & CuSn10Pb10 | Low-maintenance | DIN 1494 / ISO 3547 BIV-MET® is a low-maintenance bronze plain bearing. However, initial lubrication is required—both oil and grease lubrication are possible. Due to the lubricant depots, the relubrication intervals are greatly reduced! For high loads and oscillating movements as well as for rough operation and temperature load. For high load capacity and oscillating movement, as well as for rough operation and temperature load. Long-run lubrication because of lubricant storage. For technical details, please visit the product page on our website!

Wrapped composite sliding bearing with lubrication pockets/ copper-plated steel & AlSn20Cu | Low-maintenance | DIN 1494 / ISO 3547 For high sliding speeds, optimum sliding behaviour with good lubricant supply. BIV-MET®/A is a composite sliding bearing requiring maintenance; oil or grease lubrication is needed. For technical details, please visit the product page on our website!

Wrapped composite sliding bearing with lubrication pockets/ copper-plated steel & CuSn10Pb10 & graphite | maintenance-free | DIN 1494 / ISO 3547 BIV-LUB® is a maintenance-free composite plain bearing with solid lubricant depots. Initial lubrication is necessary! High load capacity with low wear, very suitable for low sliding speeds and oscillating movements. For technical details, please visit the product page on our website!

Rolled composite plain bearing | Maintenance-free | Steel / graphite bronze | With embedded solid lubricants GAP-MET®/S is a maintenance-free composite plain bearing. However, oil or grease lubrication is possible. High load capacity and strength, for all slow movement types, suitable for contaminated environments, no moisture absorption, good chemical resistance. For technical details, please visit the product page on our website!

For your specific requirements we customize the filter cartridge housings made of stainless steel, brass or chromed exactly Filtertechnik Jäger offers you custom-made multi cartridge housings made of polypropylene.

For your specific requirements we customize the filter cartridge housings made of stainless steel, brass or chromed exactly Filtertechnik Jäger offers you custom-made single cartridge housings made of polypropylene.

The single cartridge housings of Filtertechnik Jäger are customized to your specifications and are made of stainless steel.

For your specific requirements we customize the filter cartridge housings made of stainless steel, brass or chromed exactly Filtertechnik Jäger offers you custom-made multi cartridge housings made of stainless steel.

Robust stainless steel check valve with high flow capacity for aggressive media and high operating temperatures.

Pneumatic actuated threeway valve with an integrated positioner for demanding applications. Due to the stainless steel design suitable for neutral and aggressive media Whitworth pipe thread NPT thread Digital positioner type 8049 Pneumatic and electropneumatic positioner type 8047 Positioner with integrated process controller type 8049 IPC Positioner type 8047 and type 8049 also in explosionproof version Piston actuator of Brass (chrome plated) Stainless steel Polymer Stainless steel diaphragm actuator Different control functions such as distributing and mixing function Low temperature version Degreased version, Silicon or PTFEfree version …

Pneumatic control valve in flange design. The integrated positioner Type 8049 offers a compact design. All wetted parts are made of stainless steel. Flanges acc. DIN EN 10921 Flanges acc. ANSI #150 Digital positioner type 8049 Pneumatic and electropneumatic positioner type 8047 Positioner with integrated process controller type 8049 IPC Positioner type 8047 and type 8049 also in explosionproof version Piston actuator of Brass (chrome plated) Stainless steel Polymer Stainless steel diaphragm actuator Low temperature version Pressure balanced version Degreased version, Silicon or PTFEfree version …

Flanged valve with stainless steel body for normal and aggressive media. Installation length and flange pattern according to DIN and ANSI.Flanges acc. to DIN EN 10921 Length acc. to DIN EN 5581 series 1 Limit switch Pilot valve Manual override . . . Piston actuator of Brass (chrome plated) Stainless steel Polymer Stainless steel diaphragm actuator Low temperature version Pressure balanced version Degreased version, Silicon or PTFEfree version …

SPIROL offers a line of austenitic stainless steel Disc Springs in diameters ranging from Ø8mm to Ø71mm. Austenitic stainless steel is typically used for static and low cycle applications that require a heightened level of corrosion resistance. It withstands fresh water and atmospheric marine conditions very well, and is suitable for many other industrial conditions including acidic environments. This material will continue to work harden with use so cycle life is limited, but creep resistance is good. SPIROL supplies both single Disc Springs as well as Pre-Stacked Disc Springs in custom configurations, packaged in shrink wrap with a perforated tab for easy of assembly.

SPIROL manufactures Coiled Spring Pins out of 316 stainless steel to meet specific application requirements. Type 316 stainless steel is similar to 302/304 stainless steel with a slightly higher nickel content and the addition of molybdenum. The molybdenum content increases the chemical resistance of this alloy greatly. 316 exhibits superior pitting resistance against sea water, acetic acid vapors, chlorides, sodium and calcium brines, hypochlorite solutions, phosphoric acid, and the sulfite liquors and sulfurous acids used in the paper and pulp industry. This alloy is also austenitic, non-magnetic and non-hardenable using conventional methods. 316 stainless steel has better mechanical properties at elevated temperatures than 302/304 and offers excellent mechanical integrity at subzero temperatures. Typical applications for SPIROL's 316 Stainless Steel Coiled Pins include the following: marine, processing equipment, industrial, oil and gas and medical.

“A brewhouse should be worth showing off” —but not only that. When choosing the central component of a brewery, one shouldn’t compromise in terms of quality and longevity. After all, this is an investment in the future. An investment that will ideally bring you success for a generation or more! You can look forward to a streamlined production system without the malfunctions. That means better beer and the satifaction of your customers, ultimately the key to your success. We have the right equipment for the task: • The highest manufacturing quality and energy efficiency • Absolutely reliable, lifetime performance • Easy operation and maintenance • High aesthetic standards for the brewery’s outer appearance

ELKY special cables pass a strict manufacturing and cleaning process, in accordance with medical industry standards. Fundamentally, we only supply low twist and low tension wires and cables with a clean, high sheen, regular surface finish. We deliver manufactured products with extruded insulation made from bio-compatible materials. As well as the standard materials 1.4301 (AISI 304), 1.4310 (AISI 301), 1.4401 (AISI 316), 1.4404 (AISI 316L) and 1.4441 (AISI 316LVM), all other cabling materials authorised for use can be supplied coated and un-coated. Applications: - Guide cables e.g. for stomach tubes - Hollow cables - Strands for Temporary Myocardial Pacing Wires (monopolar, bipolar and quadripolar) - Surgial cutting strand for example for sternal closure - Strands for vein eraser - Surgical cutting strands - Wire and cables for endoscopic applications - Wire and cables for orthopaedic applications

Coated and un-coated manufactured special cables and wires made from a variety of raw materials can be used in various safety, control and attenuator elements in automotive engineering. We stock a wide, extremely varied, range of connection components in a variety of designs, sizes and materials, such as brass, tinplated copper, aluminium and stainless steel. Our products are made to customer specifications, in order to best meet their requirements (including breaking strength, elongation, flexing properties, corrosion resistance, DC resistance, low twist and low tension design, workability). Our manufacturing processes are permanently monitored and secured using appropriate procedures. As standard, we use both galvanised and stainless steel wire in accordance with DIN EN 10 264 with nominal strength of over 3000 Mpa with adequate ductility. We also use the non-corroding materials 1.4301 (AISI 304), 1.4310 (AISI 301) and 1.4401 (AISI 316) as standard.

Special application ELKY offers customer-oriented individual solutions for a wide variety of purposes. ELKY offers customer-oriented individual solutions for a wide variety of purposes; we deliver to the - Lighting technology (holding, tensioning, securing elements) - Equipment technology (telescopic pull-out safeguards) - jewelry industry Tell us your application and your specification and we will develop and manufacture a tailor-made product based on our production spectrum.

In close cooperation with machine manufacturers from all over the world, thodacon GmbH develops, manufactures and improves telescopic steel covers for all requirements, suitable for a wide range of different machine tools. Whether horizontal, vertical, oblique or transversal - there is no installation situation for which there is no optimum thodacon cover. Difficult guidance geometries or unfavorable space conditions in special machines are solved by individual constructions. The covers impress with their robustness and reliability.