Control switches - Import export

The DC-voltage converters developed for the electronic components in the motor car are characterised by their ease of installation in every vehicle. The high degree of stability, the compact design, sustained short-circuit resistance as well as the high level of operating safety are the quality hallmarks of this series. The areas of application span the mobile employment of 12-V-consumers in vehicles with a 24-V-onboard network. The devices are particularly suitable for operating car radios, stereo units, radios, cooler units, car telephones, computers, 12-V-trailer lighting etc. The voltage converter converts an input direct voltage into an output direct voltage. The input voltage must be greater than the output voltage. No base load is required at the output end. A 26 kHz PWM switching controller is used for this purpose. Input and output are not isolated. The common earth is connected with the voltage converter housing.

The sliding gate motor valve type 8030 in reinforced design is suitable for a wide range of process applicationsis suitable for a wide range of process applications. Media such as steam, liquids, gases, etc. can pefectly be controlled with this valve. Metal bellows Position electronics Analog stroke feedback Limit switch Control actuators or 3point actuators Thrust 0.9 kN; 2 kN; 4.5 kN Voltage 230 VAC, 24 VAC, 400 V, 24 VDC

The sliding gate motor valve type 8030 is suitable for a wide range of process applicationsis suitable for a wide range of process applications. Media such as steam, liquids, gases, etc. can pefectly be controlled with this valve. Metal bellows Position electronics Analog stroke feedback Limit switch . . . Control actuators or 3point actuators Thrust 0.9 kN; 2 kN; 4.5 kN Voltage 230 VAC, 24 VAC, 400 V, 24 VDC

The sliding gate control valve type 8043 in a reinforced version and long design with piston actuator and integrated positioner is due to its compact design universally applicable for neutral and aggressive media in the chemical industry, process engineering and plant design. Due to the direct and backlashfree installation of the positioner on that piston actuator, these valves have no exposed moving parts and are characterized by a high control quality and control dynamics. Digital positioner type 8049 Electropneumatic positioner type 8047 Pneumatic positioner Positioner with integrated process controller Metal bellows Limit switch Position feedback Pilot valve . . .

Experience the pinnacle of marking and coding efficiency with the MPERIA Controller. Seamlessly switch messages in seconds, enhance mark quality, and centralize coding control on your production lines regardless of equipment manufacturer. With over 170 years of expertise, we ensure ongoing support, making us your reliable partner today and beyond. Legacy Controller Challenges Companies grappling with outdated, inflexible marking systems face significant challenges in streamlining their product, case, or pallet marking processes. These systems are difficult to use, lacking automation features, and hinder seamless integration into existing production environments. The absence of user-friendly interfaces and manual code changeovers lead to increased errors, bottlenecks, and inefficient operations, resulting in unnecessary labor hours and costly recalls. There is a pressing need for an easier-to-use, automated marking solution that enables efficient integration, improves

Two in one: construction hoist with 500 kg loading capacity and transport platform for 3 persons max. Very innovative is the new foldable platform and a fork take-up point is included as standard. The GEDA 300 Z/ZP lift is perfect for operation in narrow driveways and backyards as the flat cable bin is saving even more space. There are different reasons to decide in favour of the GEDA 300 Z/ZP: The usage as construction hoist or transport platform (possible by using two separate controls), safety devices (limit switches, speed dependent safety brake, overload switch-off) and the using of the GEDA UNI-MAST are only a few convincing arguments for the GEDA 300 Z/ZP.

To view and download the brochure please click on the left image. This egglayer / block making machine is solid and productive. The COMPACT is suitable for the production of block elements up to a height off 330 mm. The stable, torsion-proof frame and the solid processing also enabel production under extreme climatic conditions. Control system Reliable control unit (Picture: semi-automatic version) for the precise control of the motion. Programming is possible according to desires of the client without programming unit. Inductive limit switches Contactless, space saving and wear resistant limit switches guarantee a secure and precise switching function. Control panel The control panel is easy to operate and was specially designed for the environment of concrete plants. Hydraulic Reliable, state of the art HAWE-hydraulic unit (picture: semi-automatic version). Security standrad High security standards in regards to working reliability and accident prevention. Frequency...

Machine Base Heavily ribbed cast iron structure for vibration-free performance. Adjustable slideways for wheelhead infeed and workhead traverse. Wheelhead Box type monobloc noted for its excellent vibration dampening characteristics. The precision motor grinding spindle is permanently sealed and lubricated. Workhead Located on a swivel plate which can be set to the required angular position by means of a wide-spaced scale. Collets for perfect valve alignment. Dressing Attachment The dressing attachment is permanently mounted on the worktable for rapid wheel dressing. Wet Grinding Coolant is delivered by an industrial type flood pump. The baffled coolant tank is easily removed from the machine base for cleaning. Electrical System Individual grinding spindle motor, work spindle motor and coolant pump motor all controlled by switches grouped in front of the wheelhead for ease of operation.

Rack mounting power supply, primary switched, remote controllable Input AC 100 - 240 V (wide range), Active-PFC For use in switch cabinets (TS35-rail acc. to EN 60715) Electrical safety / test report: IEC 60950-1, EN 60950-1, UL 60950-1, CSA 22.2 No. 60950-1, UL 508, IEC 62103, EN 50178 etc. EMC: EN 55011 Class B, EN 61000-3-2, EN 61000-6-2, EN 61204-3 No inrush current Floating relay contact Digital-I/O, Analog-IN (0 - 10 V or 4 - 20mA) Interface: RS-232 Very low stand-by-power, high efficiency (smooth behaviour across total input voltage range) Extensive protection for power output: short circuit, no-load, overvoltage, overtemperature

Rack mounting power supply, primary switched, remote controllable Input 380 - 500 V; 3 AC (wide range), Active-PFC For use in switch cabinets (TS35-rail acc. to EN 60715) Electrical safety / test report: IEC 60950-1, EN 60950-1, UL 60950-1, CSA 22.2 No. 60950-1, UL 508, IEC 62103, EN 50178 etc. EMC: EN 55011 Class B, EN 61000-3-2, EN 61000-6-2, EN 61204-3 No inrush current Floating relay contact, Digital-I/O, Analog-IN (0 - 10 V or 4 - 20 mA) Interface: RS-232 Very low stand-by-power, high efficiency (smooth behaviour across total input voltage range) Extensive protection for power output: short circuit, no-load, overvoltage, overtemperature

Rack mounting power supply, primary switched, remote controllable Input AC 100 – 240 V (wide range), Active-PFC For use in switch cabinets (TS35-rail acc. to EN 60715) Electrical safety / test report: IEC 60950-1, EN 60950-1, UL 60950-1, CSA 22.2 No. 60950-1, UL 508, IEC 62103, EN 50178 etc. EMC: EN 55011 Class B, EN 61000-3-2, EN 61000-6-2, EN 61204-3 Very low stand-by-power, high efficiency (smooth behaviour across total input voltage range) No inrush current Floating relay contact, Digital-I/O, Analog-IN (0 - 10 V or 4 - 20 mA) Interface: RS-232 Extensive protection for power output: short circuit, no-load, overvoltage, overtemperature

Rack mounting power supply, primary switched, remote controllable Input 380 - 500 V; 3 AC (wide range), Active-PFC For use in switch cabinets (TS35-rail acc. to EN 60715) Electrical safety / test report: IEC 60950-1, EN 60950-1, UL 60950-1, CSA 22.2 No. 60950-1, UL 508, IEC 62103, EN 50178 etc. EMC: EN 55011 Class B, EN 61000-3-2, EN 61000-6-2, EN 61204-3 Very low stand-by-power, high efficiency (smooth behaviour across total input voltage range) No inrush current Floating relay contact, Digital-I/O, Analog-IN (0 - 10 V or 4 - 20 mA) Interface: RS-232 Extensive protection for power output: short circuit, no-load, overvoltage, overtemperature

Rack mounting power supply, primary switched, remote controllable Input AC 100 - 240 V (wide range), Active-PFC For use in switch cabinets (TS35-rail acc. to EN 60715) Electrical safety / test report: IEC 60950-1, EN 60950-1, UL 60950-1, CSA 22.2 No. 60950-1, UL 508, IEC 62103, EN 50178 etc. EMC: EN 55011 Class B, EN 61000-3-2, EN 61000-6-2, EN 61204-3 Extensive protection for power output: short circuit, no-load, overvoltage, overtemperature Very low stand-by-power, high efficiency (smooth behaviour across total input voltage range) No inrush current Floating relay contact Digital-I/O, Analog-IN (0 - 10 V or 4 - 20mA) Interface: RS-232

Rack mounting power supply, primary switched, remote controllable Input AC 100 – 240 V (wide range), Active-PFC For use in switch cabinets (TS35-rail acc. to EN 60715) Electrical safety / test report: IEC 60950-1, EN 60950-1, UL 60950-1, CSA 22.2 No. 60950-1, UL 508, IEC 62103, EN 50178 etc. EMC: EN 55011 Class B, EN 61000-3-2, EN 61000-6-2, EN 61204-3 Extensive protection for power output: short circuit, no-load, overvoltage, overtemperature Very low stand-by-power, high efficiency (smooth behaviour across total input voltage range) No inrush current Floating relay contact Digital-I/O, Analog-IN (0 - 10 V or 4 - 20 mA) Interface: RS-232

Rack mounting power supply, primary switched, remote controllable Input AC 100-240V, Active-PFC wide range For use in switch cabinets (TS35-rail acc. to EN60715) Electrical safety / test report: IEC 60950-1, EN 60950-1, UL 60950-1, CSA 22.2 No. 60950-1, UL 508, IEC 62103, EN 50178 etc. EMC: EN 55011 Class B, EN 61000-3-2, EN 61000-6-2, EN 61204-3 Very low stand-by-power, high efficiency (smooth behaviour across total input voltage range) Floating relay contact, Digital-I/O, Analog-IN (0 - 10 V or 4 - 20 mA) Interface: RS-232 Extensive protection for power output: short circuit, no-load, overvoltage, overtemperature

Inherently RFI/EMC immune and most flexible in its class The joysticks of the series 842 exhibit properties, which are normally found in bigger joystick models only, even though it is a very compact finger joystick. Particularly worth mentioning is the possibility to configure the three axes independently and the option for a friction clutch in x and/or y-axis. The series is equipped with potentiometers, because potentiometers are still the best choice if EMI/RFI resistance requirements are very high. The joysticks are available with up to 3 axes, and exhibit a robust mechanical metal mechanism. This way the return properties of the x and y-axis can be changed by e.g. using a stronger or weaker spring, or by using a friction clutch.

The joysticks of the TRY100 series cover a great variety of different applications due to their high number of configuration options, and convince technically in every respect The TRY100 is the all-rounder in the field of finger joysticks because of the extensive selection of handles, limiters and output options. Optionally, redundant sensors are available. Thus, the joysticks can be optimized for almost all possible applications. With the convenient plug-in contact and the small installation depth of < 26 mm, the joystick offers unequalled opportunities in case of space-limitations below the panel. Due to its modern contact-less hall-sensors, the electro mechanics guarantee for a long mechanical life expectancy of 5 million operations. The construction is laid-out for a load resistance up to 200 N, and improved handle options offer protection up to IP67 above the panel.

High-quality haptics for one-dimensional control tasks The proportional rockers of the PW30 series meet the highest demands on quality and reliability for long-term use in industrial environments. With the look of a rocker switch but the sensor technology of industrial joysticks, the PW30 series combines the advantages of joysticks (for transmitting an analogue control variable) with those of toggle switches (flat design, low space requirement). In addition to two different rocker shapes, choices between potentiometric or Hall-effect sensor technology, as well as between spring return to the centre position or to the end position, are possible. Redundant versions are also available on request.

The thumb joysticks of the TRY14 series cover a great variety of different applications due to their high number of configuration options The TRY14 is the all-rounder in the field of thumb joysticks because of the extensive selection of handles, limiters and output options. The size of these joysticks can be compared with the ones that are widely used in gamepads, but the TRY14 is integrated into an industrial-suited housing with a reliable mechanism. Typical applications range from remote controls, arm rest integration or integration into larger joystick handles to industrial or medical robot arms.

The medium-sized hand joysticks of the 870 series with stock grip handle were specially developed for the multi-axis control of machines in demanding applications with highest requirements on quality and feel. The joysticks are a guarantee for success in demanding applications with up to three axes, where quality, durability and reliability are paramount. The precision manufacturing of the joystick results in a particularly high-quality feel that conveys a safe operating feeling and enables the user to precisely control movements in several dimensions. Thanks to the non-contact Hall effect technology and the optional double outputs, the joysticks are extremely reliable and safe to use even in the toughest conditions. The joystick is electrically connected via a 12-pin connector, which enables easy installation. The installation depth of <49 mm is particularly advantageous when space is limited.

Finger Joystick Series TRY22 Industrial joystick for three axes of the highest quality in terms of mechanics, materials and workmanship Exceptional quality of mechanics and sensors For demanding applications Contact-less, wear-free Hall Effect technology Redundant outputs available Protection available up to IP65 (above panel) The TRY22 series was developed strictly following criteria such as cost efficiency, high quality level, high IP classes und easy installation.

Reliable switching with spring return mechanism thanks to the 851 joystick with good price/performance ratio The series 851 switch sticks feature a functional but space-saving design. The optimized mechanics, including a stainless steel metal shaft, combined with micro switches allow for reliable switching for currents up to 10 A and voltages up to 240 V, while only taking less than 24 mm space below the panel. The spring return mechanism guarantees for safe control of the application. A cross- and one-dimensional limiter are both supplied with the shipment. The protection is IP65 above the panel. On request, switches with gold-plated contacts are available for corrosive surroundings.

The adaptability of the sensors in the premium joystick series 826 is unequalled in the field of joysticks The joystick series 826 fulfils the highest demands on quality. It shows its strengths at challenging applications with up to 2 axes, where no compromises are made when it comes to endurance and reliability, and the application asks for special sensor configurations. Die configuration options of the series 826 are unique: both axes exhibit a separated shaft for the sensors, so that the sensors, micro switches and return mechanism (spring return/friction clutch) can be adjusted individually. Especially for safety critical applications, this series is often the only series that offers the necessary options to fulfil the requirements.

Unique: The TRY20 offers 3 axes and is still a compact thumb joystick The joysticks of the TRY20 series are unique in their class thanks to their rotatable knob, which, as a z-axis, offers an additional third, proportional degree of freedom for controlling the application. The industrial joysticks achieve the highest level of quality in terms of mechanics, materials and workmanship. The high-quality haptics convey a secure operating feeling and enable the user to precisely control movements in several dimensions. Double (redundant) outputs are optionally available, which enable use in safety-critical applications. Variants with protection class IP40 (hardcover) and sealed variants (rubber bellows) with protection class IP54 are available. If the z-axis (the rotatable knob) is not required, the 2-axis version with protection class IP65 can be implemented as a special version.

Space-saving, compact – but rugged nonetheless The TRY50 series covers the transition from finger- to hand-size joysticks. This is realized by a construction of the very robust mechanism combined with space-saving Hall sensors. The TRY50 was specifically developed for applications, where a rugged hand joystick is needed, but space is limited. The optimized dimensioning of the mechanism and control lever make it possible to use the joystick in environments, where only finger joysticks would fit, but lack the needed load resistance. The joystick is equipped with Hall sensors and thus shows only minimal drift of the output signal over many years of operation. Optionally, redundant sensors can be chosen to further increase reliability.