High pressures - Import export

Grease lubrication of unsheltered parts subject to heavy loading and/or impacts, such as friction, rolling and pivoting bearings, splined shafts, knockout spindles, threaded spindles and sliding surfaces of all kinds For harsh operating conditions Advantages and benefits Excellently suited as a safety lubricating grease in mixed friction sector with especially good wear protection Effectively protects against corrosion Contains Mox-active to improve performance For best results clean the lubricating point carefully. Clean with solvents like OKS 2610/OKS 2611 Universal Cleaner. Remove the corrosion protection ahead of the initial filling. Fill the bearings in a way that all the functional surfaces for sure get the grease. Slow moving bearings(DN-value < 50,000) should be filled completely, normal moving bearings should be filled to 1/3 of the free inner housing space. Observe the instructions of the bearing or machine manufacturer. Relubrication with a grease gun on to the grease

Lubricating and sealing off tap cocks, labyrinth seals, stuffing boxes and packings Lubricating and sealing off fittings made of metal, plastic and ceramic, e.g. drain, cold- and hot-water fittings Long-term lubrication of heavily loaded press and guide plates, for example on telescope booms of mobile cranes As a lubricant for of threaded spindles on radiator thermostats Advantages and benefits Reduces wear Extension of the relubrication intervals High resistance to oxidation Noise and vibration-damping Resistant to cold and hot water, water vapour, lactic, formic, acetic and fruit acid, as well as alkaline and acidic cleaning agents and disinfectants Good elastomer and plastic compatibility For optimum adhesion, clean contamination and other lubricants from slide surfaces. Best way is to clean mechanically first and then with OKS 2610/OKS 2611 universal cleaner. Apply sufficient paste evenly with a brush, spatula, etc. The paste will also act as a sealant.

What you can expect from an APROVIS process gas heat exchanger: - Suitable for low and high temperature ranges - Operating pressures up to 160 bar - Compact design for use in confined spaces - Suitable for a wide range of gases - Implementation of customised solutions

Tried and tested release agent, which is qualified for glueing and welding of structural castings Temperature Range 130 °C to 350 °C Alloy Al, Mg, Zn Properties and Advantages • ideally suitable for conventional as well as micro-/minimal spraying • approved for glueing, welding, painting and powder coating • no build-up • die wetting already at lower temperatures

■ 1 and 2 channel drivers ■ Sensor protection class IP68 ■ Driver protection class IP40 or IP68 ■ Analog output ■ Low current consumption ■ High dynamics ■ High electromagnectic immunity

Rolling and friction bearing lubrication, even at high temperatures Lubrication for bearings with contact to cleaning agents or disinfectants For mechanical units such as levers, joints and hinges, also under strong water effect Advantages and benefits NSF H1 registered (OKS 480 & OKS 481) High shear stability prevents thinning out of the grease under extreme mechanical loads such as during vibrations Excellent wear protection and very good high-pressure properties The calcium sulphonate complex soap ensures excellent water resistance and very good corrosion protection Broad temperature application range (-30°C to +160°C) High temperature and oxidation stability through fully synthetic base oil Very high resistance to water-alkaline or acidic disinfectants and cleaning agents MOSH/MOAH-free

Rolling and friction bearing lubrication, even at high temperatures Lubrication for bearings with contact to cleaning agents or disinfectants For mechanical units such as levers, joints and hinges, also under strong water effect Advantages and benefits NSF H1 registered High shear stability prevents thinning out of the grease under extreme mechanical loads such as during vibrations Excellent wear protection and very good high-pressure properties The calcium sulphonate complex soap ensures excellent water resistance and very good corrosion protection Broad temperature application range (-30°C to +160°C) High temperature and oxidation stability through fully synthetic base oil Very high resistance to water-alkaline or acidic disinfectants and cleaning agents Also available as spray version OKS 481 MOSH/MOAH-free

Lubrication of friction and rolling bearings of all kinds at all permissible speeds and subject to high pressure loads, in particular of heavily loaded rolling and taper roller bearings, e.g. on rolling stands, hot and cold shearing systems, sliding blocks and spindles Advantages and benefits Excellently suited for long-term lubrication of grease lubricating points subject to heavy loading Highly effective due to outstanding EP additives and high resistance to water

The various output sizes and temperature ranges up to 190 °C of the UT-M enable flexible operation for countless process heat and heating applications. — Efficient heat and process heat for low running costs and emissions — Compact design for easy positioning and quick heating — Flexible use for industrial, commercial and district heating applications with temperatures up to 190 °C — Project-specific control solutions and optional real-time monitoring — Complete system from a single source, low-emission or CO2-neutral customer-specific operation possible — Proven and maintenance-friendly construction for a long service life and reliability — Fuel: Oil, gas, multi-fuel firing, Biogas, bio-oil, hydrogen, special fuels

Two independent firing units and flue gas paths create a double control range for individual heat consumption. — Very high efficiency across all power ranges — Particularly suitable for highly fluctuating heat and process heat demand — Reliable solutions for heating plants and the manufacturing industry with temperature levels up to 225 °C — Heat supply for the future: Low-NOx or CO2-neutral operation possible — Complete system with intelligent control technology and protected remote connection — Proven and durable boiler technology Made in Germany — Fuel: Oil, gas, multi-fuel firing, Biogas, bio-oil, hydrogen, special fuels

The UT-H is suitable for processes in high temperature and pressure ranges. The boiler can also convert to climate-neutral fuels which makes it a future-proof solution. — High-pressure hot water boiler from 820 to 18,300 kW with very high efficiency levels — Versatile operation for the manufacturing industry and district heating grids with temperature levels up to 225 °C — Customer-specific design and future-proof technology — User-specific control which offers integration of other control systems and remote monitoring — Custom designs for heat recovery boilers — Proven and reliable construction Made in Germany

Concrete pavers and slabs as well as natural stone pavers are cleaned with it down to the joints and appear fresh and clean again. Joints soiled by moss and sediments are also easily cleaned with the special spray cans. A particular advantage here is the integrated splash guard, thanks to which there is no nuisance to passers-by or pollution of the adjacent environment. Protective clothing and subsequent cleaning operations, which are unavoidable with conventional cleaning equipment, are no longer necessary with the Easyclean EC-60. With the four large wheels of the Easyclean EC-60, pushing is also particularly easy.

Application The portable HD 2500 is designed for delivering high hydraulic pressure up to 2500 bar required for operating hydraulic tools, especially hydraulic tools for loosening and tightening the clamping connections provided at large diesel engines. Capacity hydraulic pressure up to 2500 bar. Drive medium Compressed air with at least 6 bar. Features The hydraulic pressure is adjustable up to 1500 bar. Up to four hydraulic tools can be supplied simultaneously.

Application The portable HD 1500 is designed for delivering high hydraulic pressure up to 1500 bar required for operating hydraulic tools, especially hydraulic tools for loosening and tightening the clamping connections provided at large diesel engines. Capacity hydraulic pressure up to 1500 bar. Drive medium Compressed air with at least 6 bar. Features The hydraulic pressure is adjustable up to 1500 bar. Up to four hydraulic tools can be supplied simultaneously.

Scope of application: -Suitable for heavy machining work, single pieces and small batches -Designed particularly for use on conventional milling machines Product features: -Clamping force preselection, 2 to 4 increments, allows accurate repetition (type 100 – 2 increments; types 125, 160 – 4 increments) -Our tried and tested HD vice enables problem-free working with high clamping force and long-term reliability -Particularly suitable for single-piece production if you wish to make your vice rotatable -Can be removed at any time -Swivel base supporting edge larger than the vice‘s maximum clamping range -Swivels 360° without indexing -Alignment on the machine with T-keys in slots in the swivel base -Clamping slots arranged in the form of a ring for machines with different slot spacings

Scope of application: -Horizontal installation – suitable for vertical CNC-controlled milling machines -Lateral installation is also possible Product features: -Extreme accuracy for your machining -Clamping force can be preset in 11 increments; fine gradations for delicate workpieces. At most, 1 revolution is required max. to reach the max. clamping force -Preselectable and reproducible clamping forces enable the workpiece position to be repeated within a tolerance of less than 0.01 mm

Scope of application: -Horizontal and vertical installation – suitable for both vertical and horizontal CNC-controlled milling machines -Lateral installation is also possible Product features: -Extreme accuracy for your machining -The TC vice is ground and polished on all sides -Clamping force can be preset in 11 increments – fine gradations for delicate workpieces. At most, one revolution is required to reach the max. clamping force -Preselectable and reproducible clamping forces enable the workpiece position to be repeated within a tolerance of less than 0.01 mm

Scope of application: -Can be applied horizontally or vertically – therefore suitable for vertical and horizontal CNC milling machines -Conventional clamping, gripper clamping or pull-down clamping are all possible -Clamping unmachined parts, saw-cut or flame-cut material by penetration of hardened, replaceable gripper elements into the workpiece -With the support jaws, unmachined parts in highly varied materials, or with complex geometries, can be clamped securely and economically. Product features: -High versatility – the modular clamping system combines practically all the possibilities of our tried-and-tested model -High-pressure spindle with power intensification. -Enlarged clamping span for secure clamping of unmachined parts -Lost clamping margin 8 mm with pull-down, 3 mm with GRIPPER -Clamping near to neutral axes -Clamping jaws of forerunner are compatible -Clamping range of the middle fixed jaw groove: Max clamping width -176 mm

Scope of application: -Horizontal & vertical use - therefore suitable for vertical & horizontal CNC milling machines -Conventional clamping, grip clamping and low tension clapping possible -Titanium 2 K - ideal for use on 5-axis machining centers -Clamping of raw, thermal & saw cut parts by penetrating hardened & interchangeable grip elements into the work piece -The support jaws safely & cost effectively allow raw part, different types of materials & complex geometries to be handled Product features: -To monitor & optimize milling processes -Safety for people & machines -High flexibility - the modular clamping system combines almost all possibilities of our tried & tested models -Titanium 2 M - finely polished sides so that all sides can be used -Titanium 2 K and M can be vertically used -Force translated high-pressure spindle. -Increased power stroke for safe clamping of raw parts -Loss of 8 mm clamping edge in low tension, 3 mm with GRIPP

Scope of application: -Horizontal installation – suitable for vertical CNC-controlled milling machines Product features: -Extreme accuracy for your machining Clamping force can be preset in 4 to 11 increments. At most, 2 revolutions are required to reach the max. clamping force -Preselectable and reproducible clamping forces enable the workpiece position to be repeated within a tolerance of less than 0.01 mm

Scope of application: -Horizontal installation – suitable for vertical CNC-controlled milling machines Product features: -Extreme accuracy for your machining -Clamping force can be preset in 4 to 11 increments. At most, 2 revolutions are required to reach the max. clamping force - Preselectable and reproducible clamping forces enable the workpiece position to be repeated within a tolerance of less than 0.01 mm

Scope of application: -Suitable for heavy machining work, single pieces and small batches -Designed particularly for use on conventional milling machines Product features: -Clamping force preselection, 2 to 4 increments, allows accurate repetition (type 100 – 2 increments; types 125, 160 – 4 increments) -Our tried and tested HD vice enables problem-free working with high clamping force and long-term reliability

Scope of application: -For horizontal & vertical usage-suitable for CNC controlled milling machines & large machining centres -Clamping unmachined parts, saw-cut or flame-cut material by penetration of hardened, replaceable gripper elements into the workpiece -With the support jaws, unmachined parts in highly varied materials, or with complex geometries, can be clamped securely -Gripper studs suitable for materials with a strength of up toapprox. 1000N/mm² Product features: -High versatility – the modular clamping system combines practically all the possibilities of our tried-and-tested models -Fully compatible with the accessories of the LC/TC 160 series, for example gripper studs, universal gripper set & pull down sets -Grounded sides so that all sides can be used High-pressure spindle with mech. force amplifier for the safe clamping of raw parts in combination with gripping & pull down spring function -Lost clamping margin 8 mm with pull-down, 3 mm with GRIPPER

Scope of application: -Horizontal installation – suitable for vertical CNC-controlled milling machines Product features: -Extreme accuracy for your machining -Clamping force can be preset in 4 to 11 increments. At most, 2 revolutions are required to reach the max. clamping force -Preselectable and reproducible clamping forces enable the workpiece position to be repeated within a tolerance of less than 0.01 mm Important: -LC 200: jaw width 200 mm, width of vice base 164 mm

Scope of application: -Suitable for heavy machining work, single pieces and small batches -Designed particularly for use on conventional milling machines Product features: -Clamping force preselection, 2 to 4 increments, allows accurate repetition (type 100 – 2 increments; types 125, 160 – 4 increments) -Our tried and tested HD vice enables problem-free working with high clamping force and long-term reliability

Scope of application: -Horizontal and vertical use - therefore suitable for vertical and horizontal CNC milling machines -Conventional clamping, grip clamping and low tension clapping possible -Titanium 2 K - ideal for use on 5-axis machining centers -Clamping of raw, thermal and saw cut parts by penetrating hardened and interchangeable grip elements into the work piece -The support jaws safely and cost effectively allow raw part, different types of materials and complex geometries to be handled Product features: -To monitor and optimize milling processes -Safety for people and machines -High flexibility - the modular clamping system combines almost all possibilities of our tried and tested models -Titanium 2 M - finely polished sides so that all sides can be used -Titanium 2 K and M can be vertically used Force translated high-pressure spindle -Increased power stroke for safe clamping of raw parts -Loss of 8 mm clamping edge in low tension, 3 mm with GRIPP

Scope of application: -Horizontal and vertical use - therefore suitable for vertical and horizontal CNC milling machines -Conventional clamping, grip clamping and low tension clapping possible -Titanium 2 K - ideal for use on 5-axis machining centers -Clamping of raw, thermal and saw cut parts by penetrating hardened and interchangeable grip elements into the work piece -The support jaws safely and cost effectively allow raw part, different types of materials and complex geometries to be handled Product features: -To monitor and optimize milling processes -Safety for people and machines -High flexibility - the modular clamping system combines almost all possibilities of our tried and tested models -Titanium 2 M - finely polished sides so that all sides can be used -Titanium 2 K and M can be vertically used -Increased power stroke for safe clamping of raw parts Loss of 8 mm clamping edge in low tension, 3 mm with GRIPP

Scope of application: -Can be applied horizontally or vertically – therefore suitable for vertical and horizontal CNC milling machines -Conventional clamping, gripper clamping or pull-down clamping are all possible -TITAN 2 K – ideal for use on five-axis machining centres -Clamping unmachined parts, saw-cut or flame-cut material by penetration of hardened, replaceable gripper elements into the workpiece -With the support jaws, unmachined parts in highly varied materials, or with complex geometries, can be clamped securely and economically. Product features: -High versatility – the modular clamping system combines practically all the possibilities of our tried-and-tested models -High-pressure spindle with power intensification. Clamping force does not slacken -Enlarged clamping span for secure clamping of unmachined parts -Lost clamping margin 8 mm with pull-down, 3 mm with GRIPPER -Clamping near to neutral axes -Clamping jaws of forerunner are compatible

Scope of application: -Can be applied horizontally or vertically – therefore suitable for vertical and horizontal CNC milling machines -Conventional clamping, gripper clamping or pull-down clamping are all possible -Clamping unmachined parts, saw-cut or flame-cut material by penetration of hardened, replaceable gripper elements into the workpiece -With the support jaws, unmachined parts in highly varied materials, or with complex geometries, can be clamped securely and economically. Product features: -High versatility – the modular clamping system combines practically all the possibilities of our tried-and-tested models -The TITAN 2 M is ground an polisched on all sides -High-pressure spindle with power intensification -Enlarged clamping span for secure clamping of unmachined parts -Lost clamping margin 8 mm with pull-down, 3 mm with GRIPPER -Clamping near to neutral axes -Clamping jaws of forerunner are compatible