Results for
SPIROL
Germany
SPIROL’s GD100 Ground Hollow Dowels are designed to be direct replacements for Ground Solid Dowels manufactured per ISO 8734 when used in alignment applications. This innovative product is manufactured from strip steel, and then OD ground to achieve extremely tight diameter tolerances that enable critical alignment up to 20µm. The main advantage of the GD100 Ground Hollow Dowel is its ability to achieve the same alignment as the Ground Solid Dowel with a significant reduction in cost due to its hollow construction. In most scenarios, the Ground Hollow Dowel is approximately 50% lighter and at least 30% less expensive than the solid equivalent. If installation equipment is required, SPIROL also offers a standard comprehensive line of Installation Equipment from manual to fully automatic modules, with or without out fixturing, to support your assembly requirements.
Request for a quoteSPIROL
Germany
SPIROL’s Dowel Bushings and Spring Dowels are designed to maintain alignment and are used to locate components with respect to each other. These roll-formed, hollow Alignment Dowels have lead-in chamfers that facilitate insertion into the holes of both mating components. The Dowel's flexibility enables absorption of wide hole tolerances and the staggered seam prevents interlocking. Dowel Bushings are designed with an inside diameter clearance that allows the passage of a bolt for fastening, thereby eliminating the need to drill an additional hole. They are also heat treated to isolate the bolt from shear loads.
Request for a quoteSYSKOMP GMBH - EMICO
Germany
Flat washers ~DIN 125 (~DIN EN ISO 7089) Material: PP Colour: natural
Request for a quoteSYSKOMP GMBH - EMICO
Germany
Flat washers ~DIN 9021 (~DIN 34816) Material: PA Colour: natural
Request for a quoteSYSKOMP GMBH - EMICO
Germany
Flat washers ~DIN 433 (~DIN EN ISO 7092) Material: PA Colour: natural
Request for a quoteSYSKOMP GMBH - EMICO
Germany
Flat washers ~DIN 125 (~DIN EN ISO 7089) Material: PVDF Colour: natural
Request for a quoteSYSKOMP GMBH - EMICO
Germany
Flat washers ~DIN 125 (~DIN EN ISO 7089) Material: PA Colour: natural
Request for a quoteSYSKOMP GMBH - EMICO
Germany
Suitable for all rotating and moving parts. Ideal for silent hinges and low-speed machines. Electrical insulation between shaft and bearing housing. Material: PA 6.6 Colour: natural Due to its gliding properties and high wear resistance, polyamide is also very applicable during dry running. Resistant to fouling, atmospheric influences and to the majority of chemicals. After assembly the bearing clearance is approx. 1% of the shaft diameter. Further types or materials on written request.
Request for a quoteSYSKOMP GMBH - EMICO
Germany
Suitable for all rotating and moving parts. Ideal for silent hinges and low-speed machines. Electrical insulation between shaft and bearing housing. Material: PA 6.6 Colour: natural Item with last digits 599 = dyed black by emico Due to its gliding properties and high wear resistance, polyamide is also very applicable during dry running. Resistant to fouling, atmospheric influences and to the majority of chemicals. After assembly the bearing clearance is approx. 1% of the shaft diameter. Further types or materials on written request.
Request for a quoteSYSKOMP GMBH - EMICO
Germany
For the protection of surfaces like enamel, paint, textile, glass, ceramic etc. Also suitable for decoration purposes. Material: PA 6 Colour: black
Request for a quoteSYSKOMP GMBH - EMICO
Germany
For the protection of surfaces like enamel, paint, textile, glass, ceramic etc. Also suitable for decoration purposes. Material: PA 6 Colour: Last digits 599 = black Last digits 500 = white
Request for a quoteSYSKOMP GMBH - EMICO
Germany
For the protection of surfaces like enamel, paint, textile, glass, ceramic etc. Also suitable for decoration purposes. Material: PA 6 Colour: Last digits 599 = black Last digits 500 = white
Request for a quoteSYSKOMP GMBH - EMICO
Germany
For the protection of surfaces like enamel, paint, textile, glass, ceramic etc. Also suitable for decoration purposes. Material: PA 6 Colour: Last digits 599 = black Last digits 500 = white
Request for a quoteSYSKOMP GMBH - EMICO
Germany
For the protection of surfaces like enamel, paint, textile, glass, ceramic etc. Also suitable for decoration purposes. Material: PA 6 Colour: Last digits 599 = black Last digits 500 = white
Request for a quoteSYSKOMP GMBH - EMICO
Germany
For the protection of surfaces like enamel, paint, textile, glass, ceramic etc. Also suitable for decoration purposes. Material: PA 6 Colour: Last digits 599 = black Last digits 500 = white
Request for a quoteSYSKOMP GMBH - EMICO
Germany
For the protection of surfaces like enamel, paint, textile, glass, ceramic etc. Also suitable for decoration purposes. Material: PA 6 Colour: Last digits 599 = black Last digits 500 = white
Request for a quoteSYSKOMP GMBH - EMICO
Germany
These insulating cases combine electrical insulation with high mechanical strength. As they are resistant to electrolytic corrosion, they are essential for connections between incompatible metals. Material: PA-glass fibre reinforced Colour: black Colour white on written request.
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
SYSKOMP GMBH - EMICO
Germany
Washers with flange Wall thickness: 8.13 mm Material: LDPE Colour: yellow
Request for a quoteSYSKOMP GMBH - EMICO
Germany
Prevent electrolytic corrosion of screws with counter-sunk heads. Frequently applied in the lighting and electrotechnical industry. Compulsory by law in many countries. Furthermore a good protection for countersunk screws. Absorb vibrations. Material: PA 6 Colour: natural Further types on written request.
Request for a quoteSYSKOMP GMBH - EMICO
Germany
Protection of transformers, installations, lighting fixtures etc. Material: PA 6 Colour: natural Further types on written request.
Request for a quoteSYSKOMP GMBH - EMICO
Germany
Flat washers ~DIN 125 (~DIN EN ISO 7089) form A Material: zinc-plated steel (final digits 52) stainless steel (final digits 53)
Request for a quoteHORTON EUROPE GMBH & CO. KG
Germany
Suspension Products Horton Roller Bushings Suspension Product last for hundreds of thousands of miles so they rarely need to be replaced — saving you costly downtime and repair costs. Traditional spring pins and bushings aren't designed to withstand the daily abuses of the road. Roller Bushings from Horton provide a long-term lubrication necessary for a properly maintained suspension system. Now you can eliminate the worry of seized pins and front wheel hop. Benefits - Smoother ride - Improved handling - Less chassis stress - Trouble-free solution Features - Special ribbed casing for easier installation - Patented needle bearings provide maximum lubrication - Dual lip seals keep dirt out Links - Order or View Literature - Roller Bushings Suspension Product Catalog
Request for a quoteFATH GMBH
Germany
To fit leveling feet to round, non-threaded tubes or to fit levelling feet to profiles at right angles Threaded plug/threaded bush: To accommodate adjustable feet on the end face of square tubes or round tubes. Threaded sleeve: To accommodate adjustable feet at right angles to the profile; a hole must be drilled with Ø 17 mm through the profile to allow application Threaded plug/sleeve: Material: : PA plastic, glass-fibre reinforced / threaded insert: nickel-plated brass Colour: black, silver Extras: conductive, other sizes, other colours on request Threaded sleeve: Material: steel Colour: silver Extras: further sizes and surfaces on request
Request for a quoteIWIS ANTRIEBSSYSTEME GMBH & CO. KG
Germany
Bush conveyor chains are often used for conveying tasksinvolving long transport distances at relatively low speeds. Since only a small minority of chains used in the industry are totally compliant with one specific standard, ELITE conveyor chains are custom-made to a specific customer order and consequently fulfil a large number of special requirements. ELITE highlights: • Pins usually made of heat-treated alloy steel, inductionhardened • Bushes made from seamless precision steel tube, case-hardened • Link plates made of high-strength tempered steel or case-hardened steel alloy • Rollers (where present) made of case-hardened steel, case-hardened
Request for a quoteIWIS ANTRIEBSSYSTEME GMBH & CO. KG
Germany
Many ELITE hollow pin chains are constructed to the dimensionsof standard ISO 606. Since customer requirements are so diverse, the ELITE product range has also been adapted to include various versions of this chain type: • Hollow pin roller chains • Hollow pin bush chains • Bushless hollow pin roller chains ELITE highlights: • Available based on the same chains manufactured to ISO 606 or as special chains • All ELITE chain plates 1 are manufactured using processes such as fine blanking and ball-drifting, so a particularly high contact ratio is guaranteed. • Solid, case hardened rollers 2 with good wear resistance • In general, hollow pins 3 made of seamless precision steel tube for improved precision and wear resistance • Many of these chains are supplied pair-matched to ensure exact parallel running, one of the main requirements that these chains must fulfil.
Request for a quoteIWIS ANTRIEBSSYSTEME GMBH & CO. KG
Germany
iwis not only manufactures sprockets and plate wheels according to ISO 606 but also customized versions built in accordance with your specifications, drawings or samples. Sprockets Our standard range of sprockets includes sprockets according to ISO 606 from size 05B-1 to 32B-3. Sprockets with taper-lock bushes Taperlock-bushes for fixing hubs precisely and axially centered on a shaft. Plate wheels Standard plate wheels for the complete iwis product program: sizes 05B-1 to 32B-3. Drive sprockets and idler wheels For the FLEXON Flat Top Chain program. Our drive components program consists of torque limiters, Couplings, Tensioners, Chain tools and etc.
Request for a quoteIWIS ANTRIEBSSYSTEME GMBH & CO. KG
Germany
the context of the ELITE conveyor chain range, iwis suppliesa wide variety of chains according to standards DIN 8165 and DIN 8167, as well as models manufactured according to British Standard with dimensions in inches, and highly diverse special versions. Bush conveyor chains are often used for conveying tasks involving long transport distances at relatively low speeds. Since only a small minority of chains used in the industry are totally compliant with one specific standard, ELITE conveyor chains are custom-made to a specific customer order and consequently fulfil a large number of special requirements. Product range: • Bush conveyor chains according to DIN 8167 – M Series • Carrier chains with rollers according to DIN 8167 – MT Series • Hollow pin chains according to DIN 8168 – MC Series • Hollow pin chains according to DIN 8165 – FVC Series • Scraper chains according to DIN 8165/DIN 8167 • Conveyor chains for the paper industry • Rotary chains
Request for a quoteETTINGER GMBH
Germany
Insulating Bushings, Bearing Sleeves, Molded Insulators, Insulating Washers Since 1964 the innovative family business Ettinger GmbH has been your dependable partner for electronic and mechanical components. Customers benefit from our wide one-stop product range, excellent stock availability and reliable delivery. Our range covers everything from spacers to switches in many designs. We have more than 28,000 products available from stock. Nationally and internationally many manufacturers have classed us as an A-supplier of the category C parts they require daily. Long-standing collaboration with leading manufacturers guarantees consistently high product quality which is also constantly controlled by our quality assurance system, certified in accordance with DIN EN ISO 9001:2008.
Request for a quoteResults for
Bushings - Import exportNumber of results
29 ProductsCompany type