Alarm device - Import export

Statox 501 PID - the Allrounder PIDs (Photo – Ionisation – Detectors) detect VOCs (Volatile Organic Compounds) in the ppm range, which other sensor types are unable to monitor, like solvents and fuels. A PID sensor uses high energy ultra violet light radiation to break gas molecules into radicals, which are discharged while passing a condenser. The discharge current increases proportional to the number of molecules, i. e. the gas concentration. The standard Statox 501 PID will detect all substances with a ionization energy below 10,6 eV PIDs are normally calibrated with Isobutene. Other gases will be detected with different sensitivity. These so - called response factors must be multiplied with the displayed concentration when adjusting span. Compur Monitors will adjust your Statox 501 PID individually to your application ex works. A magnetic pin gives access to simple parameter setting and calibration menu. A multi - color LED signalises the status of the system. The Statox 501 PID voltage output signal is similar the the signal of a catalytic sensor. The Statox 501 control module displays the measured value and provides an analog output and 3 powerful relay outputs for alarm devices or pcs. Technical Data Material: Housing Interface Cast aluminum, Stainless steel

Fixed gas detection system for oxygen, toxic and combustible gases This DIN – rail mounted modern control module saves space, money and installation time. One safe controller for all gases: Any combination of a sensor head plus control module is a complete gas detection system. This makes the Statox 501 so safe and reliable. The Statox 501 also gives you the opportunity to alter or expand existing systems with minimum cost and labor. Programs for all gases and measuring ranges are permanently stored in the memory of the controller. The user-friendly software program allows authorized personnel to select different configurations by a simple push of a button. Easy to install and easy to use The controll modules as well as the power supply and the common alarm module clip on to a DIN rail. The remote sensor heads and any alarm or recording devices connect to terminals on the front of the module. Each Statox 501 control module has three relays for alarm 1 and 2 and system failure (115 / 230 V AC / 2 A). An analog output for recorder or process control systems is also included. Measured values are displayed on a 4 digit LED-display. It is easy to program or calibrate the Statox 501! Just follow the menu! If intrinsically safe transmitters are to be installed in division 1 areas, they can be connected via intrinsically safe repeaters. 24 V power supply as well as the signals for the common alarm module are transmitted via bus from one module to the next. All terminals are easily accessible from the front. Field proven sensors for reliable gas detection Compur manufactures electrochemical sensors for the detection of oxygen deficiency and toxic gases. These sensors generate an electrical current proportional to the actual gas concentration. The remote sensor heads are designed as intrinsically safe certified 4 - 20 mA transmitters and have an integrated concentration display. Combustible gases can be detected with a variety of catalytic beads (pellistors) or infrared technology. The sensor heads are certified "Ex d" or "Ex de" and can be connected directly to the control module, even if they are to be used in classified areas. The control module can supply and operate different designs of catalytic sensors. With so many possibilities, the system can easily be tailored to suit your individual application needs. Easy maintenance saves time and money Maintenance of the 4 – 20 mA transmitters is very easy. A one-man calibration or replacement of the sensors can be done without further precautions, even in classified areas. Accessories A range of wall-mount cabinets for a maximum of 5, 8 or 32 controllers as well as a 19”-carrier, ensure an easy professional installation. -20 - +60 °C

Compur Statox 502 Control - and Common Alarm Module The All – Rounder in Gas Detection No matter if you want to detect toxic or combustible gases: This control module works with any sensor head. It provides the power supply and processes the signal. Three highly rated relays and a 4 – 20 mA output are the interfaces to peripheral instrumentation. Potential front ends may be the Statox 501 or Statox 505 transmitters with electrochemical or infrared sensors, or sensor heads with a Wheatstone bridge signal such as Statox 501 PID, catalytic or the Statox 501 LC and MC series with infrared sensors. Just by the push of a button you can program the module to handle 4 – 20 mA sink or source. Even the bridge voltage can be set to any value between 2 and 5.2 V, it even works with sensor heads of other manufacturers. So there is no restriction at all when selecting the appropriate sensor head for you application. With its two “sense” lines it can even compensate the voltage drop in the cable for very remote sensor heads or if there are extreme temperature variations. For maximum flexibility the measuring range is user programmable. You can also select the unit, no matter if it is ppb, ppm, % LEL or % volume. Easy installation The control module is mounted on a standard DIN rail. With an optional power rail you can interface the 24 V DC power and the alarm signals. This way you can program one of the modules to operate as a common alarm module. Even this function can be programmed just by push button. The application of a control module as a common alarm module is a very useful feature. It displays when any of the modules goes into Alarm 1, 2 or system alarm, and controls peripheral alarm devices. All electrical contacts are located easily accessible on the front side. The terminals for alarm signals, analog output, sensor head connection run into 6 pluggable terminal blocks. This makes not only the first installation quick and easy, but also any service event or system modification. A module can easily be removed out of its row, without interrupting its neighbors or disconnecting wires. Intuitive User Interface You want a gas detection system that needs little or no attention. No matter if setting the initial parameters or performing scheduled calibrations or proof tests: The handling shall be safe, quick and easy. The password - protected Statox 502 software structure is so clear that most menu items are self - explanatory. The “Reset” button brings you time back into the measuring mode at any time. Even if you have to interrupt your work and forget to reset, the watchdog function returns the system into the measuring mode, if no button has been pushed for a while. Functional safety paired with utmost system flexibility The Statox 502 complies with the standards DIN EN 61508 and 61511 functional safety, level SIL 2. In context with the HRC or ARE sensor heads you can create a complete gas detection system for combustible gases complying with SIL 2 standard. In larger installations signals of gas detectors often run into SIL certified process control systems, in smaller plants there is a need for a control module complying with SIL requirements. As any combination sensor head / control module forms a complete gas detection system, this system closes the gap. It is expandable without limits, and there is no restriction to the mix of sensor heads connected. Connecting other front ends The versatility of the Statox 502 does not end with gas detection. You can connect any front end providing a 4 – 20 mA analog signal or a Wheatstone bridge signal. So you can create your own compact control system for a variety of sensors with just one type control device. Accessories Useful accessories such as calibration adapters, intrinsically safe repeaters, Power supplies etc. complete the system. 205 VAC, 8 A min. make or break power >/= 12 V, 10 mA, contakte silver / nickel